﻿<?xml version="1.0" encoding="utf-8"?><Search><pages Count="146"><page Index="1" isMAC="true"><![CDATA[        2021 Yamaha Boat 210FSH SPORT 210FSH DELUXE
 OWNER’S/OPERATOR’S MANUAL
U.S.A. Edition
LIT-18626-13-02 F4A-F8199-13
  Read this manual carefully before operating this boat.
 ]]></page><page Index="2" isMAC="true"><![CDATA[  WARNING: Operating, servicing and maintaining a recreational marine vessel can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, service your vessel in a well-ventilated area and wear gloves or wash your hands frequently when servicing this vessel.
For more information go to www.P65warnings.ca.gov/marine
Read this manual carefully before operating this boat. This manual should stay with the boat if it is sold.
]]></page><page Index="3" isMAC="true"><![CDATA[To the owner
Thank you for choosing a Yamaha boat. This owner’s/operator’s manual contains informa- tion you will need for proper operation, main- tenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your new Yamaha. If you have any questions about the operation or maintenance of your boat, please consult a Yamaha Boat Dealer.
In this manual, information of particular im- portance is distinguished in the following ways:
This is the safety alert symbol. It is used to alert you to potential personal injury haz- ards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING
A WARNING indicates a hazardous situa- tion which, if not avoided, could result in death or serious injury.
NOTICE
A NOTICE indicates special precautions that must be taken to avoid damage to the boat or other property.
TIP:
A TIP provides key information to make pro- cedures easier or clearer.
Important manual information
Engine data recording
This model’s ECM stores certain engine data to assist in the diagnosis of malfunctions and for research, statistical analysis and develop- ment purposes.
Although the sensors and recorded data will vary by model, the main data points are:
  Engine status and engine performance
data
This data will be uploaded only when a spe- cial Yamaha diagnostic tool is attached to the engine, such as when maintenance checks or service procedures are performed.
Yamaha will not disclose this data to a third party except in the following cases. In addi- tion, Yamaha may provide engine data to a contractor in order to outsource services re- lated to the handling of the engine data. Even in this case, Yamaha will require the contrac- tor to properly handle the engine data we provided and Yamaha will appropriately manage the data.
  With the consent of the boat owner
  Where obligated by law
  For use by Yamaha in litigation
  For general Yamaha-conducted research
purposes when the data is not related to an individual engine or owner
       ]]></page><page Index="4" isMAC="true"><![CDATA[Important manual information
 Because Yamaha has a policy of continuing product improvement, this product may not be exactly as described in this owner’s/oper- ator’s manual. Specifications are subject to change without notice.
This manual should be considered a perma- nent part of this boat and should remain with it even if the boat is subsequently sold.
   210FSH SPORT/210FSH DELUXE OWNER’S/OPERATOR’S MANUAL ©2021 by Yamaha Motor Corporation, U.S.A.
1st Edition, June 2020
All rights reserved.
Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in U.S.A.
P/N LIT-18626-13-02
 ]]></page><page Index="5" isMAC="true"><![CDATA[ General and important labels...........1
Identification number records .......... 1 Primary Identification (PRI-ID)
number ....................................... 1 Hull Identification Number (HIN) ... 1 Engine serial number .................... 1
Emission control information ........... 2
Approval label of emission
control certificate ....................... 2
Manufactured date label ............... 3
Important labels ............................... 4
Warning labels ..............................6 Other labels...................................9
Safety information...........................10
Limitations on who may operate
the boat.......................................10 Cruising limitations......................... 11 Operational requirements .............. 12 Required equipment....................... 13
Additional equipment recommendations ....................... 13
Hazard information......................... 14 Boat characteristics ....................... 14 Night operation .............................. 15 Wakeboarding and water-skiing .... 16 Rules of the road............................ 17 To get more boating safety
information .................................. 21 Enjoy your boat responsibly........... 21
Description....................................... 22
Boat glossary ................................. 22 Location of main components ....... 23 Exterior components................... 23
Stern components ...................... 26 Helm components....................... 27 Engine components .................... 29
Control function operation ............. 30
Boat control functions.................... 30
Engine shut-off switch ................ 30 Battery switches ......................... 30 Main switches ............................. 31
Table of contents
Remote control levers................. 32 Steering ...................................... 34 Tilt lever ...................................... 34
Instrument operation ....................... 36
Tachometers .................................. 36 Multi-function display unit
operation..................................... 36 Multi-function display elements..... 37 Static bar .................................... 37
Screen tab bar ............................ 38 Center display............................. 38 Warning bar ................................ 39
Home screen ................................. 39 Trip screen ..................................... 39 Setting screen................................ 41
Time setting screen .................... 41 Brightness setting screen ........... 41 Unit setting screen...................... 42 Aerator setting screen ................ 42 Maintenance setting screen ....... 43 Language setting screen ............ 43 Factory reset screen ................... 43
Warnings........................................ 45
Check engine warning ................ 46 Low oil pressure warning............ 46 Over temperature warning .......... 47 Communication error warning .... 48 No-wake mode/cruise assist
switch ...................................... 48 Operating the boat with a
minimal wake
(no-wake mode)....................... 48 Operating the boat at a steady
speed (cruise assist) ................ 48 Operating the boat in reverse
with more thrust
(reverse RPM control) .............. 49
Switches ........................................ 50
Courtesy light switch .................. 51 Navigation and anchor lights
switch ...................................... 51 Aerator switch............................. 52 Switch circuit breakers ............... 53
Accessory outlet ............................ 54 Stereo system................................ 54
]]></page><page Index="6" isMAC="true"><![CDATA[Table of contents Equipment operation ...................... 55
Seats .............................................. 55 Leaning post ............................... 55 Jump seats.................................. 55 Removable backrest ................... 56
Engine hood ................................... 56 Storage compartments .................. 57 Anchor storage compartment ..... 57
Bow storage compartment ......... 57 Insulated fish box........................58 Stern storage compartment........58 Lockable storage
compartment............................ 59 Glove compartment .................... 62 Storage pocket ........................... 62 Wet storage compartment .......... 63 Bucket storage compartment ..... 63 Rod holders................................. 64 Livewell ....................................... 65 Battery compartment .................. 66
Windshield...................................... 67 Anchor light (210FSH SPORT) ....... 67 Anchor light (210FSH DELUXE) ..... 68 Swim platform................................70
Ladder ......................................... 70 Jet wash.........................................71
T-top (210FSH SPORT).................. 73 Bimini top (210FSH SPORT) .......... 74 Bimini top (210FSH DELUXE) ........ 75
Setting up the bimini top.............75 Storing the bimini top in the
upright position ........................ 76 Storing the bimini top in the fully
collapsed position....................76 Trailering with the bimini top.......77
Operation and handling requirements......................................78
Fuel requirement ............................ 78
Fuel ............................................. 78 Engine oil requirement ................... 79
Engine oil..................................... 79 Draining the bilge water ................. 81
Draining the bilge water on
land .......................................... 81
Draining the bilge water on
water ........................................ 82
First-time operation ......................... 84
Engine break-in.............................. 84
Pre-operation checks ..................... 85
Pre-operation checklist............... 85 Pre-operation check points ........... 87
Pre-launch checks ...................... 87 Steering system checks ............. 87 Remote control lever checks ...... 87 Fire extinguisher check............... 88 Access port cap check ............... 89 Jet intake checks........................ 90 Fuel system checks .................... 90 Engine oil level check ................. 90 Battery check.............................. 91 Bilge water check ....................... 91 Drain plug check......................... 91 Blower switch check................... 92 Navigation and anchor lights
switch check............................ 92 Horn switch check ...................... 93 Engine shut-off cord (lanyard)
check ....................................... 93 Post-launch checks .................... 94 Engine shut-off switch check ..... 94 Cooling water pilot outlet
check ....................................... 94 Fuel level check .......................... 94
Operation........................................... 96
Driving your boat ........................... 96
Getting to know your boat .......... 96 Learning to operate your boat .... 96 Starting the engine ..................... 96 Stopping the engines.................. 98 Leaving a dock ........................... 99 Turning the boat ......................... 99 Boating with passengers .......... 101 Stopping the boat..................... 101 Boarding from the water........... 102 Boarding from a dock or
landing jetty ........................... 102 Docking..................................... 102 Beaching................................... 103 Anchoring ................................. 103
 ]]></page><page Index="7" isMAC="true"><![CDATA[ Crossing wakes and swells.......104 Post-operation checks.................105
Trailering ........................................ 107
Trailering the boat ........................ 107
Hitch .......................................... 107 Trailering checklist .................... 107 Backing your trailer ................... 108 Launching ................................. 108 Loading ..................................... 109 Lifting ........................................ 110
Care and storage........................... 111
Post-operation care ..................... 111
Flushing the cooling system ..... 111 Cleaning the boat......................112 Basic stain guide....................... 114 Battery care............................... 115
Long-term storage ....................... 116
Fuel system...............................116 Lubrication ................................ 116 Grease points............................116
Maintenance ....................................118
Maintenance................................. 118
Owner’s/operator’s manual ...... 118 Periodic maintenance chart ...... 119
Specifications ..................................122
Specifications............................... 122
Trouble recovery .............................124
Troubleshooting ........................... 124
Troubleshooting chart...............124 Emergency procedures................126
Jet pump clean-out procedure............................... 126
Jump-starting............................ 128 Fuse replacement ..................... 128 Towing the boat ........................ 130
Consumer information..................131
Limited warranty .......................... 131 YAMAHA EXTENDED SERVICE
(Y.E.S.) ...................................... 133
Table of contents
Sample float plan......................... 134
Index................................................. 135
]]></page><page Index="8" isMAC="true"><![CDATA[General and important labels
 Identification number records
Record your Primary Identification (PRI-ID) number, Hull Identification Number (HIN), and engine serial number in the spaces provided to assist you in ordering spare parts from your Yamaha Boat Dealer. Also, record and keep these ID numbers in a separate place in case your boat is stolen.
Primary Identification (PRI-ID) number
The PRI-ID number is stamped on a label at- tached inside the engine compartment. (See page 56 for engine hood opening and closing procedures.)
Hull Identification Number (HIN)
The HIN is stamped into the right rear corner of the hull.
          YAMC
1
1 Hull Identification Number (HIN)
Engine serial number
The engine serial numbers are stamped on a label attached to each engine unit. (See page 56 for engine hood opening and closing pro- cedures.)
     1
      1
         1
Primary Identification (PRI-ID) number
PRI-I.D.
MODEL
YAMAHA MOTOR CO.,LTD.
ASSEMBLED IN U.S.A. WITH FOREIGN & DOMESTIC COMPONENTS.
ASSEMBLÉ EN U.S. AVEC DES COMPOSANTS ÉTRANGERS ET DOMESTIQUES.
      1 Engine serial number
 1
]]></page><page Index="9" isMAC="true"><![CDATA[ Port side
General and important labels
Emission control information
This engine family conforms to U.S. Environ- mental Protection Agency (EPA) regulations for marine SI engines applicable at the time of manufacture.
This engine is certified to operate on regular unleaded gasoline.
Approval label of emission control certificate
These labels are attached to each engine unit and to the inside of the engine compartment. (See page 56 for engine hood opening and closing procedures.)
   YAMAHA
YAMAHA MOTOR CO., LTD. MADE IN JAPAN
PAYS D’ORIGINE JAPON
        1
Starboard side
   YAMAHA
YAMAHA MOTOR CO., LTD. MADE IN JAPAN
PAYS D’ORIGINE JAPON
     1 Emission control information label
 EMISSION CONTROL INFORMATION
THIS ENGINE CONFORMS TO   U.S. EPA EXHAUST REGULATIONS FOR SI MARINE
ENGINES. REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
  ENGINE FAMILY : DISPLACEMENT :
MAX POWER : kW EPA FEL : HC+NOx   , CO   g/kW-h
YAMAHA MOTOR CO.,LTD.
liters
       1
1 Emission control information label
2
]]></page><page Index="10" isMAC="true"><![CDATA[General and important labels
   Manufactured date label
This label is attached to each engine unit. (See page 56 for engine hood opening and closing procedures.)
      1
   1 Manufactured date label
3
EMISSIONS CONTROL SYSTEM INFORMATION
THIS ENGINE CONFORMS TO U.S. EPA EXHAUST REGULATIONS FOR SI MARINE ENGINES. REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. MEETS U.S. EPA EVAP STANDARDS USING CERTIFIED COMPONENTS. ENGINE FAMILY: DISPLACEMENT: liters MAX POWER: kW EPA FEL: HC+NOx ,CO g/kW-h EPA CERTIFIED EVAP COMPONENTS:
YAMAHA MOTOR CO., LTD.
             ]]></page><page Index="11" isMAC="true"><![CDATA[General and important labels
Important labels
Read the following labels before operating this boat. If you need any additional information, contact a Yamaha Boat Dealer.
         2 1
14
15
3
4
5
                         6
                             7 916 8 7
4
]]></page><page Index="12" isMAC="true"><![CDATA[General and important labels
                      10
                            12
         10 13
13 11
10
         17
                      18
                                 13 10
     5
]]></page><page Index="13" isMAC="true"><![CDATA[ 3
4
General and important labels
Warning labels
If any of these labels is damaged or missing, contact a Yamaha Boat Dealer for a replacement.
1
2
6
]]></page><page Index="14" isMAC="true"><![CDATA[ General and important labels
7
5
6
7
]]></page><page Index="15" isMAC="true"><![CDATA[ 8
9
10 11
12
General and important labels
8
]]></page><page Index="16" isMAC="true"><![CDATA[ General and important labels Other labels
13
14 15
9
16 17
18
All applicable electrical system components installed as original equipment meet appropriate U.S.C.G. requirements for ignition protection. (Ref. 33 CFR 183.410 and 183.440)
Y AMAHA 60E-83627-00
MAXIMUM CAPACITIES
10PERSONS OR 1860 LBS. 2250 POUNDS, PERSONS, GEAR
THIS BOAT COMPLIES WITH U.S. COAST GUARD SAFETY STANDARDS IN EFFECT ON THE DATE OF CERTIFICATION
MEETS U.S. EPA EVAP STANDARDS USING CERTIFIED COMPONENTS
MANUFACTURER: YAMAHA JET BOAT MANUFACTURING U.S.A., INC.
MODEL: VONORE, TN
DESIGN COMPLIANCE WITH NMMA REQUIREMENTS IS VERIFIED. MANUFACTURER RESPONSIBLE FOR PRODUCTION CONTROL.
NATIONAL MARINE MANUFACTURERS ASSOCIATION
]]></page><page Index="17" isMAC="true"><![CDATA[ The safe use and operation of this boat is dependent upon the use of proper operat- ing techniques, as well as upon the com- mon sense, good judgment, and expertise of the operator. Every operator should know the following requirements before operating the boat.
  Before operating the boat, read the own- er’s/operator’s manual, the Operation In- struction card, and all labels on the boat. These materials should give you an under- standing of the boat and its operation.
  Never allow anyone to operate this boat until they too have read this owner’s/oper- ator’s manual, the Operation Instruction card, and all labels.
Safety information
Limitations on who may
operate the boat
  Yamaharecommendsaminimumoperator age of 16 years old.
Adults must supervise use by minors. Know the operator age and training re- quirements for your state. A boating safety course is recommended and may be re- quired in your state. You can find local rules by contacting the United States Coast Guard (USCG), the National Association of State Boating Law Administrators, or your local Power Squadron.
  Thisboatisdesignedtocarrytheoperator, up to 9 passengers, and cargo. Never ex- ceed the maximum load limit or allow more than 10 persons (or 9 persons if the wake- boarder or water-skier is being pulled) to ride in the boat at any time. Weight distri- bution affects performance. Keep weight in the boat low and evenly distributed from side-to-side and bow-to-stern. Remove any unnecessary cargo and store it on shore.
   Maximum load:
Total weight of cargo, operator, and passengers:
1021 kg (2250 lb)
Total weight of operator and passen- gers:
844 kg (1860 lb)
 10
]]></page><page Index="18" isMAC="true"><![CDATA[Safety information
Cruising limitations
  Scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.
  Operate defensively at safe speeds and keep a safe distance from people, objects, and other watercraft.
  Do not follow directly behind other water- craft.
  Do not go near others to spray or splash them with water.
  Avoid sharp turns or other maneuvers that make it hard for others to avoid you or un- derstand where you are going.
  Avoid areas with submerged objects or shallow water.
  Take early action to avoid collisions. Re- member, boats do not have brakes.
  Do not pull the remote control lever back to idle when trying to steer away from ob- jects—you need throttle to steer. Always check throttle, shift, and steering controls for proper operation before starting boat.
  Operate within your limits and avoid ag- gressive maneuvers to reduce the risk of loss of control, ejection, and collision.
  Thisisahigh-performanceboat—notatoy. Sharp turns or jumping wakes or waves can increase the risk of back/spinal injury (paralysis), facial injuries, and broken legs, ankles, and other bones. Do not jump wakes or waves.
  Do not operate the boat in rough water, bad weather, or when visibility is poor; this may lead to an accident causing injury or death. Be alert to the possibility of adverse weather. Take note of weather forecasts and the prevailing weather conditions be- fore setting out in your boat.
  Never operate in water that is less than 90 cm (3 ft) deep from the bottom of the boat, otherwise you increase your chance of hitting a submerged object, which could result in injury.
  Leave a “float plan” with a responsible per- son on shore. Tell where you plan to go and when you plan to arrive, and provide a de- scription of your boat. Advise this person if your plans change and also when you ar- rive to prevent false alarms. A sample float plan is included on page 134.
  Follow navigation rules and state and local laws that apply to your boat.
        90 cm (3 ft)
11
]]></page><page Index="19" isMAC="true"><![CDATA[ Operational requirements
  Theoperatorandallpassengersmustwear a U.S. Coast Guard (USCG) approved per- sonal flotation device (PFD).
Safety information
  Attach the engine shut-off cord (lanyard) to the PFD and keep it free from the steering wheel or other controls so that the engine stops if the operator accidentally leaves the helm. Failure to attach the engine shut-off cord (lanyard) could result in a runaway boat if the operator is ejected.
After operation, remove the engine shut-off cord (lanyard) and the main switch key to avoid accidental starting or unauthorized use by children or others.
 1
             1
       2
 1 PFD
  Eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your boat. Re- straining straps for eyewear are made which are designed to float should your eyewear fall in the water.
  Never operate the boat after consuming al- cohol or taking drugs.
  For reasons of safety and proper care of the boat, always perform the pre-operation checks listed on page 85 before operating the boat.
  Passengers must always sit in a designat- ed seating area, place feet on the deck, and hold on to the handgrips when the boat is in motion.
  Always consult your doctor on whether it is safe for you to ride in this boat if you are pregnant or in poor health.
  Do not attempt to modify this boat. Modifications to your boat may reduce safety and reliability, and render the boat unsafe or illegal to use.
1 Engine shut-off switch
2 Engine shut-off cord (lanyard)
  Scan constantly for swimmers and stay away from swimming areas. Swimmers are hard to see and you could accidentally hit someone in the water.
  Avoid being hit by another boat. You should always take responsibility to watch for traffic; other boaters may not be watch- ing for you. If they do not see you, or you maneuver more quickly than other boaters expect, you risk a collision.
  Maintain a safe distance from other boats and watercraft, and also watch for ski ropes or fishing lines. Obey the “Rules of the road”, and be sure to check behind you before making a turn. (See “Rules of the road” on page 17.)
12
]]></page><page Index="20" isMAC="true"><![CDATA[Safety information
Required equipment
The U.S. Coast Guard (USCG) has regula- tions which describe minimum standards of safety. You must comply with these regula- tions, which apply to boats like your boat which are less than 26 feet long.
  Personal flotation devices (PFD):
Type I, II, or III as required for all people on board (see “Operational requirements” for more information), plus at least one Type IV (throwable type).
  Fire extinguisher:
At least one 5-B (B-1) type hand-held por- table fire extinguisher.
  Visual distress signals:
It is recommended that a USCG-approved day/night pyrotechnic device be stored on your boat. A mirror can also be used as an emergency signal. Contact your Yamaha Boat Dealer or the Coast Guard for more information.
  Sound signalling device:
Your boat is equipped with a horn that can be used to signal other boats. See “Rules of the road” for more information.
  Navigation lights:
Your boat is equipped with navigation lights for use between sunset and sunrise, and during periods of reduced visibility, such as fog. Be sure these lights are work- ing and are turned on when necessary. (See pages 51 and 68 for more informa- tion.)
Additional equipment
recommendations
The following equipment can help make your boating experience safer and more enjoy- able:
  Mooring fenders and lines.
  Anchor with suitable line (a “Danforth” type anchor and line that is at least 6 times the depth of the water where you will drop an- chor are recommended).
  Manual-type bilge pump.
  First-aid kit.
  Waterproof flashlight with extra batteries.
  Tool kit with assorted screwdrivers, pliers,
wrenches (including metric sizes), and
electrical tape.
  Oar or paddle (look for one with a boat
hook on the other end).
  Spare parts, such as fuses.
  Navigation charts for the waters where you
will be boating.
  Tow-rope.
 13
]]></page><page Index="21" isMAC="true"><![CDATA[ Hazard information
Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of con- sciousness and death within a short time. Al- ways operate the boat in an open area.
It is also important to have the engine off when anyone is using the ladder on models equipped with one because of the carbon monoxide in the exhaust gases coming from underneath the step.
Safety information
Boat characteristics
  Jet thrust turns the boat. Moving the re- mote control lever completely back to idle or the neutral position produces only mini- mum thrust. If you are traveling at speeds above trolling, you will have rapidly de- creasing ability to steer without throttle. You may still have some turning ability im- mediately after moving the remote control lever back to idle, but once the engine slows down, the boat will no longer re- spond to steering wheel input until you ap- ply throttle again or you reach a trolling speed. Practice turning in an open area without obstructions until you have a good feel for the maneuver.
  This Yamaha boat is water-jet propelled. The pump is directly connected to the en- gine. This means that the jet thrust will pro- duce some movement whenever the engine is running. The boat has a “neutral” position, but since the boat is always pro- ducing thrust while the engine is running, some forward or reverse movement may occur.
  Do not use the reverse function to slow down or stop the boat above trolling speed as it could cause you to lose control, be ejected, or impact the steering wheel or other parts of the boat. This could increase the risk of serious injury. It could also dam- age the shift mechanism.
  Reverse can be used to slow down or stop during slow-speed maneuvering, such as when docking. Once the engine is idling, shift to reverse and gradually increase en- gine speed. Make sure that there are no obstacles or people behind you before shifting into reverse.
14
]]></page><page Index="22" isMAC="true"><![CDATA[  
 
Safety information
Keepawayfromtheintakegrateswhilethe engines are on. Items such as long hair, loose clothing, or PFD straps can become entangled in moving parts, resulting in se- vere injury or drowning.
Never insert any object into the jet thrust nozzles while the engines are running. Se- vere injury or death could result from com- ing in contact with the rotating parts of the jet pumps.
Night operation
When using your boat before dawn or after dusk, you must have both bow and anchor lights operating. When at anchor in the dark, the anchor light must be lit. (See pages 51, 67 and 68 for instructions.)
210FSH DELUXE
     2
    1
210FSH SPORT
 1 2
 
Intake grate
Jet thrust nozzle
Stop the engines and remove the clip from the engine shut-off switch before removing any debris or weeds, which may have col- lected around the jet intakes. (See page 126 for more information.)
15
]]></page><page Index="23" isMAC="true"><![CDATA[ Wakeboarding and water-
skiing
You can use the boat to tow a wakeboarder or water-skier, using the ski tow hook provid- ed.
It is the boat operator’s responsibility to be alert to the safety of the wakeboarder or wa- ter-skier and others. Know and follow all state and local regulations in effect for the waters in which you will be operating.
The following are some important consider- ations for minimizing risks while pulling a wakeboarder or water-skier.
  The wakeboarder or water-skier should
wear an approved PFD, preferably a bright- ly colored one so boat operators can see the person being pulled.
  The wakeboarder or water-skier should wear protective clothing. Severe internal in- juries can occur if water is forced into body cavities as a result of falling into the water or while reboarding. Normal swimwear does not adequately protect against force- ful water entry into the rectum or vagina. The person being pulled should wear a wetsuit bottom or clothing that provides equivalent protection. Such clothing in- cludes thick, tightly woven, sturdy, and snug-fitting apparel such as denim, but does not include spandex or similar fab- rics, like those used in bicycle shorts.
Safety information
  A second person should be on board as a spotter to watch the wakeboarder or wa- ter-skier; in most states, it is required by law. Let the person being pulled direct the operator’s control of speed and direction with hand signals. Be sure the seat is locked in place (see page 55) before get- ting underway.
  When preparing to pull the wakeboarder or water-skier, operate the boat at the slowest possible speed until the boat is well away from the person being pulled and slack in the tow-rope is taken up. Make sure that the rope is not looped around anything. After checking that the wakeboarder or wa- ter-skier is ready and that there is no traffic or other obstacles, apply enough throttle to raise the person.
  Make smooth, wide turns. The boat is ca- pable of very sharp turns, which could ex- ceed the abilities of the wakeboarder or water-skier. Keep the person being pulled at least 50 m (164 ft), about twice the dis- tance of a standard tow-rope, away from any potential hazard.
  The operators of boats and other water- craft may not be aware that you are pulling a wakeboarder or water-skier. Together with the spotter, pay attention to others around you and cruise at safe speeds.
  Be alert to the hazard of the tow-rope han- dle snapping back at the boat when the wakeboarder or water-skier falls or is un- able to get up on the skis.
16
]]></page><page Index="24" isMAC="true"><![CDATA[Safety information
Rules of the road
Your Yamaha boat is legally considered a powerboat. Operation of the boat must be in accordance with the rules and regula- tions governing the waterway on which it is used.
Just as there are rules that apply when you are driving on streets and highways, there are waterway rules that apply when you are oper- ating your boat. These rules are used interna- tionally, and are also enforced by the United States Coast Guard and local agencies. You should be aware of these rules, and follow them whenever you encounter another vessel on the water.
Several sets of rules prevail according to geographic location, but are all basically the same as the International Rules of the Road. The rules presented here in this owner’s/op- erator’s manual are condensed, and have been provided for your convenience only. Consult your local U.S. Coast Guard Auxiliary or Department of Motor Vehicles for a com- plete set of rules governing the waters in which you will be operating your boat. Steering and sailing rules
Whenever two vessels on the water meet one another, one vessel has the right-of-way; it is called the “stand-on” vessel. The vessel that does not have the right-of-way is called the “give-way” or “burdened” vessel. These rules determine which vessel has the right-of-way, and what each vessel should do.
Stand-on vessel
The vessel with the right-of-way has the duty to continue its course and speed, except to avoid an immediate collision. When you maintain your direction and speed, the other vessel will be able to determine how best to avoid you.
Give-way vessel
The vessel which does not have the right-of- way has the duty to take positive and timely action to stay out of the way of the stand-on vessel. Normally, you should not cross in front of the vessel with the right-of-way. You should slow down or change directions brief- ly and pass behind the other vessel. You should always move in such a way that the operator of the other vessel can see what you are doing.
The General Prudential Rule regarding the right-of-way is that if a collision appears un- avoidable, neither boat has the right-of-way. Both boats must avoid the collision.
In other words, follow the standard rules ex- cept when a collision will occur unless both vessels try to avoid each other. If that is the case, both vessels become give-way ves- sels.
Rules when encountering vessels
There are three main situations that you may encounter with other vessels which could lead to a collision unless the Steering Rules are followed:
Meeting: you are approaching another vessel head-on.
Crossing: you are traveling across another vessel’s path.
Overtaking: you are passing or being passed by another vessel.
 17
]]></page><page Index="25" isMAC="true"><![CDATA[   Meeting
If you are meeting another power-driven ves- sel head-on, and are close enough to run the risk of collision, neither of you has the right- of-way. Both of you should alter course to avoid an accident. You should keep the other vessel on your port (left) side. This rule does not apply if both of you will clear one another if you continue on your set course and speed.
Overtaking
If you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and direction so that the other vessel can steer itself around you.
Safety information
 In the following illustration, your boat is in the center. You should give the right-of-way to any vessels shown in the white area (you are the give-way vessel). Any vessels in the shad- ed area must yield to you (they are the give- way vessels). Both you and the meeting ves- sel must alter course to avoid each other.
Crossing
When two power-driven vessels are crossing each other’s path close enough to run the risk of collision, the vessel which has the other on the starboard (right) side must keep out of the way of the other. If the other vessel is on your starboard (right) side, you must keep out of its way; you are the give-way vessel. If the other vessel is on your port (left) side, remem- ber that you should maintain course and di- rection, provided the other vessel gives you the right-of-way, as it should.
                 18
]]></page><page Index="26" isMAC="true"><![CDATA[Safety information
Other special situations
There are three other rules you should be aware of when operating your boat around other vessels.
Narrow channels and bends
When navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a power- driven vessel is preparing to go around a bend that may obstruct the view of other wa- ter vessels, the operator should sound a pro- longed blast of four to six seconds on the horn. If another vessel is around the bend, it too should sound the horn. Even if no reply is heard, however, the vessel should still pro- ceed around the bend with caution.
Fishing vessel right-of-way
All vessels fishing with nets, lines, or trawls are considered to be “fishing vessels” under the International Rules. Vessels with trolling lines are not considered fishing vessels. Fish- ing vessels have the right-of-way regardless of position. Fishing vessels cannot, however, impede the passage of other vessels in nar- row channels.
Sailing vessel right-of-way
Sailing vessels should normally be given the right-of-way. The exceptions to this are:
(1) When the sailing vessel is overtaking the
power-driven vessel, the power-driven
vessel has the right-of-way.
(2) Sailing vessels should keep clear of any
fishing vessel.
(3) In a narrow channel, a sailing vessel
should not hamper the safe passage of a power-driven vessel that can navigate only in such a channel.
Reading buoys and other markers
The waters of the United States are marked for safe navigation by the lateral system of buoyage. Simply put, buoys and markers have an arrangement of shapes, colors, num-
bers, and lights to show which side of the buoy a boater should pass on when navigat- ing in a particular direction. The markings on these buoys are oriented from the perspec- tive of being entered from seaward (the boat- er is going towards the harbor). Red buoys are passed on your starboard (right) side when proceeding from open water into port, and black buoys are to your port (left) side. An easy way to remember the meaning of the colors is the phrase “red right returning.” When navigating out of the harbor, your posi- tion with respect to the buoys should be re- versed; red buoys should be to port and black buoys to starboard.
Many bodies of water used by boaters are entirely within the boundaries of a particular state. The Uniform State Waterway Marking System has been devised for these waters.
 19
]]></page><page Index="27" isMAC="true"><![CDATA[Safety information
This system uses buoys and signs with distinctive shapes and colors to show regulatory or advisory information. These markers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information.
                                        Remember, markings may vary by geographic location. Always consult local boating author- ities before riding your boat in unfamiliar waters.
20
]]></page><page Index="28" isMAC="true"><![CDATA[Safety information
To get more boating safety
information
Be informed about boating safety. Additional publications and information can be obtained from many organizations, including the fol- lowing.
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Af- fairs
US Coast Guard Headquarters
Washington, D.C. 20593-0001 http://www.uscgboating.org
Other sources
You can find local rules by contacting the Na- tional Association of State Boating Law Ad- ministrators, or your local Power Squadron. Boat Education and Training
The Online Boating Safety Course, available through the watercraft section of the yamaha-motor.com website, is a free, 50- question learning course available to the public. Upon successful completion of 80 percent or better, the user can request a cer- tificate of completion by mail or can down- load one immediately. The Online Boating Safety Course, provided by the Boat/US Foundation, is approved by the National As- sociation of State Boating Law Administra- tors (NASBLA) and recognized by the United States Coast Guard. This course meets the education requirement for those states that recognize non-proctored, NASBLA-ap- proved courses.
The Online Boating Safety Course: http://www.boatus.org/
Enjoy your boat responsibly
You share the areas you enjoy when operat- ing your boat with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, wa- ters, and wildlife with respect and courtesy. Whenever and wherever you are boating, think of yourself as the guest of those around you. Remember, for example, that the sound of your boat may be music to you, but it could be just noise to others. And the exciting splash of your wake can make waves others won’t enjoy. Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife areas, and keep a respectful distance from fishermen, other boats, swimmers, and populated beaches. When travel in areas like these is unavoidable, operate slowly and obey all laws.
Remember that pollution can be harmful to the environment. Do not refuel or add oil where a spill could cause damage to nature. Keep your surroundings pleasant for the peo- ple and wildlife that share the waterways: don’t litter!
When you go boating responsibly, with re- spect and courtesy for others, you help en- sure that our waterways stay open for the enjoyment of a variety of recreational oppor- tunities.
   21
]]></page><page Index="29" isMAC="true"><![CDATA[Description
 Boat glossary
  TERM DEFINITION
Bow
Deck
Give-way
Gunwale
Hatch
Helm
Hull
Lanyard
PFD
Planing
Port
Stand-on
Starboard
Stern
Sub-planing
Transom
Trolling
Wake
The front part of the boat.
The “floor” or upper structure which covers the hull.
The vessel that must yield the right-of-way when two boats meet.
The meeting junction of the deck and hull; the upper edge around the boat. Pronounced “gunnel.”
An opening in the deck that provides access below.
The steering console.
The basic part of the boat; the underside.
The cord or tether that connects the operator to the engine shut-off switch so the engine will stop if the operator accidentally leaves the helm.
A personal flotation device, also known as “life jacket.”
Traveling at a speed fast enough so the boat has leveled out and is skimming on top of the water. There is a wake.
The left side of the boat.
The vessel with the right-of-way when two boats meet.
The right side of the boat.
The back part of the boat.
Traveling at a medium speed. The bow of the boat is out of the water, but you are still traveling through the water. There is a wake.
The vertical part of the stern.
Traveling at idle speed, using little or no throttle. The boat is down in the water and it is not leaving a wake.
The visible track of disturbed water that the boat leaves behind as it moves in the water.
                     22
]]></page><page Index="30" isMAC="true"><![CDATA[Description
Location of main components Exterior components
 210FSH DELUXE
 6
         5
34 2
                                           7
   1
983
3 12 1110
               12 16 15
14
2 13
1 Front starboard seat (page 55)
2 Handgrip
3 Rod holder (page 64)
4 Front console seat (page 55)
5 Windshield (page 67)
6 Anchor light (page 51, 68)
7 Fuel tank filler cap (page 78)
8 Leaning post (page 55)
9 Jump seat (page 55)
10 Courtesy light (page 51)
11 Speaker
12 Cleat
13 Front port seat (page 55)
14 Bow light (page 51)
15 Anchor storage compartment (page 57) 16 Bow eye
23
]]></page><page Index="31" isMAC="true"><![CDATA[Description
 210FSH SPORT
  7
6 5
34 2
8
3
                                                     9
   1
3
11 10 3 14 1312
               14 18 17
16
2 15
1 Front starboard seat (page 55)
2 Handgrip
3 Rod holder (page 64)
4 Front console seat (page 55)
5 T-top (page 73)
6 Windshield (page 67)
7 Bimini top (page 74)
8 Anchor light (page 51, 67)
9 Fuel tank filler cap (page 78)
10 Leaning post (page 55)
11 Jump seat (page 55)
12 Courtesy light (page 51)
13 Speaker
14 Cleat
15 Front port seat (page 55)
16 Bow light (page 51)
17 Anchor storage compartment (page 57) 18 Bow eye
24
]]></page><page Index="32" isMAC="true"><![CDATA[Description
  8 7
                  4
6 45
3 2
1
9
2 8
10 4
11
                                                           12
13 4
  16
15 14 24
1 Swim platform (page 70)
2 Cleat
3 Wet storage compartment (page 63)
4 Rod holder (page 64)
5 Ski tow hook
6 Engine hood (page 56)
7 Enclosed storage compartment (page 61)
8 Handgrip
9 Bow light (page 51)
10 Speaker
11 Courtesy light (page 51)
12 Cooling water pilot outlet (page 94)
13 Bilge pump outlet (page 82)
14 Jump seat (page 55)
15 Livewell (page 65)
16 Reboarding grip
25
]]></page><page Index="33" isMAC="true"><![CDATA[Description
 Stern components
 12
3
4
1
                             5
665
       7
11
7
9
              88 10
1 Cleat
2 Reboarding grip
3 Ski tow hook
4 Ladder (page 70)
5 Stern eye
6 Shift gate (page 32)
7 Jet thrust nozzle
8 Intake grate
9 Speed sensor
10 Hull drain plug (page 82)
11 Articulating keel (page 34)
26
]]></page><page Index="34" isMAC="true"><![CDATA[Description Helm components
  1213
                               12
11
8
10 9 7
4
5
6
            1 Tachometer (page 36)
2 Multi-function display unit (page 36)
3 Compass
4 Stereo receiver (page 54)
5 Handgrip
6 Storage pocket (page 62)
7 Remote control lever (page 32)
8 Jet wash switch (page 50)
9 No-wake mode/cruise assist switch (page 50)
10 Tilt lever (page 34)
11 Glove compartment (page 62)
12 Steering wheel (page 34)
27
]]></page><page Index="35" isMAC="true"><![CDATA[Description
       1
2
3 4
22
    NAV/ ANC
CTSY ACC ACC LIGHTS
MNL
AERATOR
AUTO
LIVEWELL
BILGE HORN
        BLOWER
6 7 8 9 10111213
       5
        12V
AUDIO AUX-USB
  1615 14
1 Main switch (page 31)
2 Switch circuit breaker (page 53)
3 Engine shut-off switch (page 30)
4 Engine shut-off cord (lanyard) (page 30)
5 Blower switch (page 50)
6 Navigation and anchor lights switch (page 51)
7 Courtesy light switch (page 51)
8 Accessory switch 1 (page 50)
9 Accessory switch 2 (page 50)
10 Aerator switch (page 50)
11 Livewell switch (page 50)
12 Bilge pump switch (page 50)
13 Horn switch (page 50)
14 Aux input (page 54)
15 12 V DC outlet (page 54)
16 Circuit breaker (page 53)
28
]]></page><page Index="36" isMAC="true"><![CDATA[Description Engine components
         12 3
12
                                 4
3 4
                        5
 1 Blower (page 92)
2 Oil tank filler cap/Dipstick (page 80)
3 Spark plug/Ignition coil
4 Air filter case
5 Fuse box (cover) (page 128)
29
]]></page><page Index="37" isMAC="true"><![CDATA[Control function operation
 Boat control functions Engine shut-off switch
WARNING
  Always attach the engine shut-off cord (lanyard) to your PFD before starting the engine. Failure to attach the cord could result in a runaway boat if the operator is ejected.
  Do not attach the cord to clothing that could tear loose. Do not route the cord in such a way that it could become en- tangled, preventing it from functioning.
  Avoid accidentally pulling the cord dur- ing normal operation. Once the engine has stopped, you have no steering con- trol of the boat which could result in an accident. Also, without engine power, the boat could slow rapidly from planing speed. This could cause people and ob- jects in the boat to be thrown forward, which could cause injury.
The clip on the end of the engine shut-off cord (lanyard) must be attached to the engine shut-off switch for the engine to run. The cord must be attached to a secure place on the operator’s PFD. Should the operator fall over- board or leave the helm, the cord will pull out the clip, stopping the ignition to the engine. This will prevent the boat from running away under power.
1 Engine shut-off switch
2 Clip
3 Engine shut-off cord (lanyard)
Battery switches
The batteries and switch assembly are locat- ed in the battery compartment.
This boat uses two marine batteries. One bat- tery is designated as the start battery. The start battery is connected to the starter circuit on the engine to provide current for the start- er motor.
The other battery is designated as the house battery. The house battery provides power for the various accessory circuits on the boat, such as the circuits for the lighting, bilge pump, blowers and audio system.
         1
   2
3
           1
2
3
  1 Battery switch assembly
2 Start battery
3 House battery
30
]]></page><page Index="38" isMAC="true"><![CDATA[Control function operation
 There are three switches on the battery switch assembly: the “START” switch, “HOUSE” switch, and “EMERG PARALLEL” switch.
If the start battery is discharged, turn the “EMERG PARALLEL” switch to the ON posi- tion to start the engine. Once the engine is started or the start battery is charged, turn the “EMERG PARALLEL” switch to the OFF position.
Main switches
There is a main switch for each engine.
The main switch controls the ignition and electrical circuits as follows:
 12
3
     1 2
OFF START ON
BLOWER
 1 “HOUSE” switch (red)
2 “EMERG PARALLEL” switch (yellow)
3 “START” switch (red)
 1
 2
  1 ON position (green)
2 OFF position (red)
In normal operation, keep the “START” and “HOUSE” switches in the ON position. Keep the “EMERG PARALLEL” switch in the OFF position. This setting allows both batteries to be charged automatically while the engine is running. NOTICE: Do not turn the “HOUSE” switch to the OFF position if the boat is moored in the water as it will prevent the anchor light from functioning.
1 Main switch (port engine)
2 Main switch (starboard engine)
OFF:
Ignition circuit is switched off. The engine cannot be started, but other switches will op- erate. (The main switch key can be removed.) ON:
Ignition circuit is switched on. (The main switch key cannot be removed.)
START:
The starter motor will turn to start the engine. (When the main switch key is released, it re- turns automatically to “ON”.)
TIP:
  Theenginewillnotstartwhentheclipisre- moved from the engine shut-off switch. The starter motor will turn over without the cord attached.
31
]]></page><page Index="39" isMAC="true"><![CDATA[  Themainswitchwillnotoperate(thestarter motor will not turn over) if the “START” switch in the battery compartment is turned to the OFF position. (See page 30 for more information.)
Remote control levers
WARNING
  Before shifting, make sure there are no swimmers or obstacles in the water near you.
  When operating in reverse, go slowly. Do not open the throttle more than half. Otherwise, the boat may become unsta- ble, which could result in loss of control and an accident.
  Do not shift into reverse while traveling at planing speeds. Loss of control, boat swamping, or damage to the boat could occur.
The remote control lever for each engine con- trols both throttle and shifting. In normal op- eration, the levers are moved together. Moving the remote control levers forward from the neutral position shifts into the for- ward position, and then as the levers are moved farther, accelerates the engines for more thrust. Moving the levers back from the neutral position shifts into the reverse posi- tion, and then as the levers are moved farther, accelerates the engines for more thrust.
For cruising, adjust the remote control levers so both engines are running at the same en- gine speed.
TIP:
Because of the mechanical throttle linkage, the remote control levers may not be exactly even with one another when the engines are running at the same engine speed.
1 Neutral position 2 TDE position
3 Forward position 4 Reverse position 5 Shift
6 Fully closed 7 Throttle
8 Fully open
TIP:
This boat is equipped with a “start-in-gear” protection. The engines will not start unless the levers are in the neutral position.
This boat uses a direct-drive propulsion sys- tem. Therefore, jet thrust is always being pro- duced while the engines are running. The direction of the boat is controlled by the shift gates, which direct the flow of the jet thrust as follows:
Neutral
The shift gates are dropped down part way over the jet thrust nozzles. The neutral posi- tion balances forward and reverse thrust to help keep the boat from moving, although some movement may occur.
Control function operation
  F2 N1 R 55
34
77 66
88
   32
]]></page><page Index="40" isMAC="true"><![CDATA[Control function operation
    1
1
            22
   1
1
2
                 2
1 Shift gate
2 Jet thrust nozzle
Forward
When the remote control levers are initially moved to the forward position and the boat is operating at a slow speed, the shift gates are lifted up slightly from the neutral position and jet thrust is directed downward at an angle. This function, which is called the thrust direc- tional enhancer (TDE), helps to provide good handling response when the steering wheel is turned, even though there is less thrust avail- able at low engine speeds.
1 Shift gate
2 Jet thrust nozzle
When the remote control levers are moved farther forward, the shift gates are lifted all the way up. All jet thrust is to the rear, which moves the boat forward.
   1
1
              22
 N F1R
  1 TDE position
1 Shift gate
2 Jet thrust nozzle
Reverse
The shift gates are dropped all the way down over the jet thrust nozzles. Jet thrust is redi- rected toward the bow of the boat, which moves the boat backward.
33
]]></page><page Index="41" isMAC="true"><![CDATA[Control function operation
              11
           11 2
          1 Shift gate
Steering
Your boat can be steered by turning the steering wheel the same direction you wish to travel, to the right or left. When the steering wheel is turned, the angle of the jet thrust nozzles at the rear of the craft is changed, and the change in direction of the jet thrust nozzles changes the direction of the boat ac- cordingly.
In addition, the direction of the articulating keel changes according to the movement of the jet thrust nozzles.
1 Jet thrust nozzle 2 Articulating keel
Since the strength of the jet thrust determines the speed and direction of a turn, the throttle must always be opened above idle when at- tempting a turn, except at trolling speed. Because boats steer from the stern, the stern of the boat swings out in the opposite direc- tion of your turn. If you turn to starboard, for example, the stern of the boat will swing to the left. Keep this in mind when navigating near a person in the water, such as a down wakeboarder or water-skier, or an obstacle, such as a dock.
Tilt lever
WARNING
  Never touch the tilt lever during opera- tion, otherwise the steering wheel could suddenly change position, which may lead to an accident.
  Be sure the steering wheel is locked in position after adjustment. If the steering wheel is not locked in position, it may suddenly change position during opera- tion, which may lead to an accident.
The tilt lever is located under the steering wheel and is used to adjust the tilt of the steering wheel. There are 5 positions.
           1
        1 Steering wheel
 34
]]></page><page Index="42" isMAC="true"><![CDATA[Control function operation
          1
  1 Tilt lever
To adjust the tilt:
(1) Push the lever down, and then move the
steering wheel up or down to the desired
position.
(2) The lever will lock into place when the
steering wheel is moved into one of the 5
available positions.
(3) Make sure that the tilt lever returns to its
original position and that the steering wheel is securely locked in place.
 35
]]></page><page Index="43" isMAC="true"><![CDATA[ Tachometers
The boat is equipped with two tachometers. The tachometer on the left is for the port en- gine. The one on the right is for the starboard engine.
The analog tachometers show the engine speed. The numbers on the meters show the engine speed × 1000 rpm (r/min).
Instrument operation
Multi-function display unit
operation
Because the multi-function display unit is equipped with a touch screen, you can touch the display directly to operate the display functions.
Touching the multi-function display
  12
                1 Port tachometer
2 Starboard tachometer
36
]]></page><page Index="44" isMAC="true"><![CDATA[Instrument operation
Multi-function display elements
  121
              10:27 am
              FUEL 100%
0
0.3 Avg MPG
WATER 67°F
12.3V
     MPH
                   12.3V
   43
1 Static bar
2 Screen tab bar
3 Center display
4 Warning bar
Static bar
 1
6 5
 10:27 am FUEL
100%
12.3V
        WATER
67°F
12.3V
2
3 4
       Name
Function
1
Fuel level bar graph
Displays the amount of fuel remaining in the fuel tank. Depending on the amount of remaining fuel, the bar graph is displayed in 3 colors: blue, yellow, and red.
      37
]]></page><page Index="45" isMAC="true"><![CDATA[Instrument operation
    Name
Function
2
Water temperature
Displays the ambient water temperature in degrees Fahrenheit or degrees Celsius.
3
Start battery voltage bar graph
Displays the start battery voltage in a bar graph format.
4
Start battery voltage val- ue
Displays the start battery voltage in a numerical format.
5
House battery voltage value
Displays the house battery voltage in a numerical format.
6
House battery voltage bar graph
Displays the house battery voltage in a bar graph format.
        Screen tab bar
 12345
   10:27 am
 Name
Function
1
Clock
Displays the time. Tap the clock to set the time. (See page 41.)
2
Home screen tab
Displays the home screen. (See page 39.)
3
Trip screen tab
Displays the trip screen. (See page 39.)
4
Setting screen tab
Displays the setting screen. (See page 41.)
5
Mute
Mutes the sound of the buzzer for a specific time depending on the warnings present.
          Center display
 1
 0 MPH 0.3 Avg MPG
    Name
1 Center display
Function
Displays various information for each screen.
  38
]]></page><page Index="46" isMAC="true"><![CDATA[Instrument operation Warning bar
  1
     Name
Function
1
Warning bar
Displays the warning icons.
When a warning icon is displayed, tap the icon to display the warning message for that icon.
    Home screen
123
Trip screen
This screen displays the hours of engine op- eration, fuel consumption, and other informa- tion.
 0 MPH
No Wake Mode
     0.3 Avg MPG
      Water : Economy : Trip : Used :
79.3 °F
23.0 Avg MPG 262.8 Miles
89.9 Gal
123
        Reset
    Name
Function
1
Boat speed
Displays the boat speed in miles per hour or kilometers per hour.
2
Cruise as- sist/no-wake mode and jet wash system status indicator
Displays the operating status of the cruise as- sist, no-wake mode, and jet wash system.
3
Data bar
Displays trip screen in- formation.
See “Trip screen” for more information.
39
1 Menu
2 Scrollbar
3 “Reset” button
The menu displays 4 items at one time. Scroll through the menu items using the scrollbar.
]]></page><page Index="47" isMAC="true"><![CDATA[Instrument operation
To reset an item on the trip screen:
Touch and hold the item that you want to re- set for several seconds.
To reset all of the display items:
Tap the “Reset” button to reset all of the items.
  Name
Function
Water tempera- ture*
Displays the ambient water temperature in degrees Fahrenheit or degrees Cel- sius.
Average fuel consumption
Displays the average dis- tance that was traveled on 1.0 gallon or 1.0 liter of fuel since the item was last re- set.
When gallons are selected for the display units, the value is displayed in miles and when liters are selected for the display units, the value is displayed in kilome- ters.
Trip distance
Displays the distance trav- eled by the boat in miles or kilometers since the item was last reset.
Fuel used
Displays the total fuel that has been consumed by the port and starboard engines in gallons or liters since the item was last reset.
Fuel flow*
Displays the total fuel con- sumption of the port and starboard engines in gal- lons per hour or liters per hour.
Highest speed
Displays the highest speed of the boat in miles per hour or kilometers per hour since the item was last reset.
Average speed
Displays the average boat speed in miles per hour or kilometers per hour since the item was last reset.
Engine hours*
Displays the total number of hours that the engines have been running since the boat was new.
              * This item cannot be reset.
40
]]></page><page Index="48" isMAC="true"><![CDATA[Instrument operation
Setting screen
The setting screen can be used to change the settings of the multi-function display unit.
   Set Time
10 1 1 am
Save Back
 8 9
9 0
9 0
am pm
          Time Unit Wellness
Menu
Aerator Brightness Language
Reset
       Item
Function
 Save
Saves the set time as the current time and displays the setting screen.
 Back
Displays the setting screen without saving the set time.
      Item
Function
  Time
Displays the time setting screen.
  Aerator
Displays the aerator set- ting screen.
  Unit
Displays the unit setting screen.
  Brightness
Displays the brightness setting screen.
  Wellness
Displays the maintenance setting screen.
  Language
Displays the language set- ting screen.
 Reset
Displays the factory reset screen.
      TIP:
When “US Unit” is selected, the time is dis- played in the 12-hour format. When “Metric Unit” is selected, the time is displayed in the 24-hour format.
Brightness setting screen
The multi-function display has a day mode and a night mode.
The brightness can be set separately for the day mode and for the night mode.
      Set Brightness
DAY NIGHT 100% 50%
Save Back
        Time setting screen
Tap the time unit that you want to set and scroll up or down.
41
]]></page><page Index="49" isMAC="true"><![CDATA[Instrument operation
  Item
Function
  NIGHT
Displays the current night mode setting.
  DAY
Displays the current day mode setting.
 Save
Saves the set brightness as the brightness level set- ting and displays the set- ting screen.
 Back
Displays the setting screen without saving the set brightness level.
 Item
Function
  US Unit
Sets the display units to US units.
  Metric Unit
Sets the display units to metric units.
 Save
Saves the selected unit setting as the current units and displays the setting screen.
 Back
Displays the setting screen without saving the select- ed unit setting.
To adjust the brightness:
To make the display darker, drag the slider to the left. To make the display brighter, drag the slider to the right.
1 Slider control
TIP:
The slider limits depend on the selected light mode.
Unit setting screen
The display units for the multi-function dis- play unit can be changed.
Aerator setting screen
The on and off time intervals for the aerator can be set.
   Aerator
   Time ON
1 min Save
Time OFF
1 min Back
    1
  Item
Function
  Time ON
Displays the on time inter- val for the aerator.
  Time OFF
Displays the off time inter- val for the aerator.
 Save
Saves the set aerator time intervals as the current aer- ator settings and displays the setting screen.
 Back
Displays the setting screen without saving the aerator settings.
  Set Unit
   US Unit
Save
Metric Unit
Back
  42
]]></page><page Index="50" isMAC="true"><![CDATA[Instrument operation
To adjust the aerator time interval setting:
1 Slider control
TIP:
To return to the maintenance setting screen without resetting the number of hours, tap the “NO” button.
1 “YES” button
Language setting screen
The language for the multi-function display unit can be changed.
     To increase the time interval setting, drag the slider to the right.
To decrease the time interval setting, drag the slider to the left.
Maintenance setting screen
This screen displays the number of hours that the engines have been running since the last maintenance.
1
  1
YES Are you sure ? NO
   Set Language
   English
Save
Espanol
Francais
Back
     Time Since Last Maintenance Port Engine
0 Hrs Starboard Engine
0 Hrs
   Reset
Back
After maintenance is performed, reset the number of hours of operation as follows.
To reset the number of hours of operation: (1) Tap the “Reset” button.
1 “Reset” button
(2) When the confirmation message ap- pears, tap the “YES” button to reset the number of hours of operation.
Tap the desired language, and then tap the “Save” button to save the setting.
To display the setting screen without saving the language setting, tap the “Back” button.
Factory reset screen
This screen can be used to reset the settings to their factory default settings.
    Factory Reset
Reset all parameters to factory setting? Reset Back
   43
1
Reset Back
 ]]></page><page Index="51" isMAC="true"><![CDATA[To reset the settings:
(1) Tap the “Reset” button.
1 “Reset” button
(2) When the confirmation message ap- pears, tap the “YES” button to reset the settings.
TIP:
To return to the factory reset screen without resetting the settings, tap the “NO” button.
1 “YES” button
Instrument operation
   1
Reset Back
  1
YES Are you sure ? NO
 44
]]></page><page Index="52" isMAC="true"><![CDATA[Instrument operation
Warnings
If a malfunction or fault occurs, a warning buzzer will sound and a warning icon and warning message will be displayed on the center display.
             10:27 am
12.3V
     FUEL 1100%
WATER 67°F
12.3V
Fuel 0 Low Fuel Level
Jet Wash Mode 1 0.3 Avg MPG
QUIT
     MPH NEXT
                  Name
Function
NEXT
Displays the next active warning. When there is only 1 warning, the dis- played warning will not change.
QUIT
Closes the displayed warning.
     If the displayed warning message includes instructions, follow those instructions. If you have any questions, consult a Yamaha Boat Dealer.
 1 2
Fuel 0 Low Fuel Level
Jet Wash Mode 0.3 Avg MPG
      MPH NEXT
 1
QUIT
           10:27 am
12.3V
     FUEL 1100%
WATER 67°F
12.3V
          1 Warning title 2 Message
Warning example
  Warning title
Message
Check Engine
  Stop Port Engine. Consult YAMAHA dealer.
  Stop Starboard Engine. Consult YAMAHA dealer.
 Low Oil Pressure
 Over Temperature
House Battery
Low Voltage.
Start engine to recharge the battery.
 High Voltage.
     45
]]></page><page Index="53" isMAC="true"><![CDATA[Instrument operation
   Warning title
Message
Start Battery
Low Voltage.
Start engine to recharge the battery.
 High Voltage.
Fuel
Low Fuel Level
Port Engine
Maintenance Due
Stbd Engine
Maintenance Due
Communication Error
Port Engine
 Starboard Engine
 Engine CAN
 Port Gauge
 Starboard Gauge
 No LIN Communications
 No transducer found
        The check engine warning indicator is also displayed on the tachometer for the engine with the warning.
Check engine warning
If an engine sensor malfunction or a short cir- cuit is detected, a warning will appear on the multi-function display and the buzzer will sound. If a fault is detected for an engine, “Check Engine” will be displayed. If this oc- curs, reduce the engine speed, return to shore, and have a Yamaha Boat Dealer check the engine.
Low oil pressure warning
If the oil pressure does not rise to specifica- tion, a warning will appear on the multi-func- tion display and the buzzer will sound. If a fault is detected for an engine, “Low Oil Pres- sure” will be displayed. At the same time, the engine speed is automatically limited to help prevent damage. If this occurs, reduce the engine speed, return to shore or maneuver to a safe location, and check the engine oil level. (See page 80 for engine oil level checking procedures.)
If the oil level is low, add enough engine oil to raise it to the proper level. If the oil level is suf- ficient, have a Yamaha Boat Dealer check the engine.
      11
MNL
NAV/ CTSY ACC ACC AERATOR LIVEWELL B ANC LIGHTS
AUTO
1 Check engine warning indicator
46
]]></page><page Index="54" isMAC="true"><![CDATA[Instrument operation
Over temperature warning
This model is equipped with an over temper- ature warning system. If the engines start to overheat, a warning will appear on the multi- function display and the buzzer will sound. If an engine is overheating, “Over Tempera- ture” will be displayed. At the same time, the engine speed is automatically limited to help prevent damage. If this occurs, immediately reduce the engine speed, return to shore or maneuver to a safe location, and check for water discharge at the cooling water pilot outlets. There are cooling water pilot outlets on the starboard side of the hull. Check that water comes out of the outlets while the en- gines are running, particularly while applying throttle. If you do not see any water at the outlets, cooling water may not be circulating in the engines.
1 Intake grate NOTICE
If the cause of overheating cannot be found and corrected, take special precau- tions to avoid major engine damage while you return to shore.
Single engine overheating — Shut off the overheating engine and use the properly running engine to return to shore. Operate at no-wake speed (8 km/h, 5 mph) to pre- vent water from flooding the non-operat- ing engine through the water intake. See page 48 for information on the no-wake mode.
Both engines overheating — If getting a tow from another vessel is not possible, operate both engines just slightly above idle while you return to shore. If you can be towed, refer to “Towing the boat” on page 130.
       1
       1
2
 1 Cooling water pilot outlet (port engine)
2 Cooling water pilot outlet (starboard engine)
TIP:
If the cooling water passages in the engines are dry, it will take about 20 seconds for wa- ter to reach the pilot outlets after starting.
If water is not circulating, something may be clogging the intake grates. Refer to “Jet pump clean-out procedure” on page 126.
 47
]]></page><page Index="55" isMAC="true"><![CDATA[ Communication error warning
If a generic error is detected, a warning will appear on the multi-function display and the buzzer will sound. If this occurs, reduce the engine speed, return to shore, and have a Yamaha Boat Dealer check the boat.
No-wake mode/cruise assist switch
This switch activates and sets the no-wake mode, cruise assist, and reverse RPM con- trol.
Instrument operation
(2) Push the plus side of the no-wake mode/cruise assist switch. Once “No Wake Mode” is displayed in the multi- function meter, the no-wake mode is ac- tivated.
   10:27 am
12.3V
 FUEL 100%
0
0.3 Avg MPG
WATER 67°F
12.3V
MPH
 No Wake Mode
               JET WASH
1
        1 No-wake mode/cruise assist switch
TIP:
The no-wake mode can be set to 3 engine speeds. To adjust the engine speed while the no-wake mode is activated, push the plus side or minus side of the no-wake mode/cruise assist switch.
To deactivate the no-wake mode: Perform one of the following operations.
  Push the minus side of the no-wake
mode/cruise assist switch until “No Wake
Mode” disappears.
  Push the remote control levers forward to
open the throttle.
Operating the boat at a steady speed (cruise assist)
The cruise assist feature is for steady engine speed operation when the boat is traveling above no-wake speeds. The cruise assist is available for use whenever the engines are running above 4000 rpm and below 7000 rpm.
To activate the cruise assist:
(1) Push the remote control levers forward
to open the throttle until the desired en-
To operate the no-wake mode and cruise as- sist, see the following sections. To activate the reverse RPM control, see “Reverse RPM control” on page 49.
Operating the boat with a minimal wake (no-wake mode)
The no-wake mode is useful for operating the boat at a steady speed with a minimal wake. This is especially convenient when traveling in harbors, channels, or other areas posted with low speed limits as “no wake zones”. The no-wake mode can be activated only when the engines are operating at idle speed. To activate the no-wake mode:
(1) Put the remote control levers in the TDE
position or forward position so that both engines are operating at idle speed.
   48
]]></page><page Index="56" isMAC="true"><![CDATA[Instrument operation
gine speed is reached and both engines
are operating at the same engine speed. (2) Push the plus side or minus side of the no-wake mode/cruise assist switch. Once “Cruise” is displayed in the multi- function meter, the cruise assist is acti-
vated.
Operating the boat in reverse with more thrust (reverse RPM control) Engine speed in reverse is limited to approx- imately 4500 rpm. If more thrust is required when the boat is traveling in reverse, use the reverse RPM control. WARNING! Be pre- pared to reduce throttle as soon as the boat moves as desired. Otherwise, the boat may become unstable, which could result in loss of control and an accident. To activate the reverse RPM control:
(1) Move the remote control levers back- ward so that the throttle is opened in re- verse and both engines are operating at the same engine speed.
(2) Increase the engine speed to 4500 rpm, and then push the plus side of the no- wake mode/cruise assist switch.
TIP:
Once the reverse RPM control is activated, pushing the plus side of the no-wake mode/cruise assist switch will increase the available engine speed by approximately 500 rpm in 3 stages up to a maximum of 6000 rpm, and pushing the minus side will decrease the available engine speed. Howev- er, the adjustment is limited to these 3 incre- ments.
To deactivate the reverse RPM control: Operate the remote control levers to de- crease the engine speed to less than 4500 rpm.
    10:27 am
12.3V
 FUEL 100%
0
Cruise +4 0.3 Avg MPG
WATER 67°F
12.3V
MPH
       TIP:
  Once the cruise assist is activated, the set engine speed can be increased by pushing the plus side of the switch or decreased by pushing the minus side. However, the ad- justment is limited to a maximum of 8 incre- ments above or below the initial cruise assist setting. Each time the switch is pushed, the engine speed will increase or decrease approximately 100–200 rpm.
  While the cruise assist is activated, the en- gine speed can also be adjusted by operat- ing the remote control levers.
To deactivate the cruise assist:
Operate the remote control levers to de- crease the engine speed to 3000 rpm or less. Once “Cruise” disappears, the cruise assist is deactivated.
  49
]]></page><page Index="57" isMAC="true"><![CDATA[Instrument operation Switches
   MNL
NAV/ CTSY ACC ACC AERATOR LIVEWELL BILGE HORN ANC LIGHTS
AUTO
12345678
   11
BLOWER
JET 9 WASH
10
   Name
Function
Page
1
Navigation and anchor lights switch
Turns the anchor light and bow light on or off.
51
2
Courtesy light switch
Turns the 2 courtesy lights and livewell light on or off.
51
3
Accessory switch 1
These switches can be used to operate a fish finder or other electronic device that is installed later as an acces- sory. For more information, contact a Yamaha Boat Dealer.
—
 4
Accessory switch 2
—
5
Aerator switch
Circulates the water in the livewell.
52
6
Livewell switch
Turns the livewell pump on or off.
65
7
Bilge pump switch
Turns the bilge pump on or off.
82
8
Horn switch
Activates the horn. The horn can be used to signal other boats as required by the “Rules of the road”.
17
9
Jet wash switch
Turns the jet wash system on or off.
71
10
No-wake mode/cruise assist switch
Activates and sets the cruise assist, no-wake mode, and reverse RPM control.
48
11
Blower switch
Turns the blower on or off to ventilate the engine compart- ment.
92
                 50
]]></page><page Index="58" isMAC="true"><![CDATA[Instrument operation
Courtesy light switch
Push this switch to turn on the 2 courtesy lights on the sides of the console and the livewell light.
Navigation and anchor lights switch
This toggle switch controls the bow light and anchor light. Push the upper side of the switch to turn on both the bow light and an- chor light for night running (“NAV”). Push the lower side of the switch to operate the anchor light alone when anchored at night (“ANC”). Put the switch in the middle position to turn off all lights. (See page 67 and 68 for more in- formation.)
               1
 1
1 Courtesy light
              1
1 Bow light 210FSH DELUXE
 1
1 Courtesy light
   1
 1 Livewell light
51
1 Anchor light
]]></page><page Index="59" isMAC="true"><![CDATA[Instrument operation
 210FSH SPORT
  1
 1 Anchor light
Aerator switch
Use this switch to circulate the water in the livewell. Push the “MNL” side of the switch to circulate water continuously in the livewell. Push the “AUTO” side of the switch to circu- late water in the livewell according to the on and off operation settings. Put the switch in the middle position to stop circulating water. (See page 42 for information on setting the automatic operation settings.)
52
]]></page><page Index="60" isMAC="true"><![CDATA[Instrument operation
Switch circuit breakers
The electrical circuit for each switch is protected by a circuit breaker. If the button pops out, push it back in with your finger. If it pops out again, ask a Yamaha Boat Dealer to inspect the electrical system.
  NAV/ ANC
CTSY ACC ACC LIGHTS
MNL
AERATOR
AUTO
LIVEWELL
BILGE HORN
JET WASH
11
      BLOWER
1
1 Switch circuit breaker
53
]]></page><page Index="61" isMAC="true"><![CDATA[ Accessory outlet
There is a 12 V DC outlet with a circuit break- er located in the storage pocket.
NOTICE
Do not use an automotive cigarette lighter or other accessories that get hot because the outlet can be damaged.
Instrument operation
Stereo system
A stereo receiver is standard. The stereo sys- tem consists of the receiver, speakers, auxil- iary input jack, USB terminal, and Bluetooth. Refer to the stereo system Operation Manual included with your boat.
        1
                  12
12V
AUDIO AUX-USB
                 12V
1 2
   1 Circuit breaker
2 12 V DC outlet
1 Stereo receiver
1 Auxiliary input jack
2 USB terminal
54
]]></page><page Index="62" isMAC="true"><![CDATA[Equipment operation Seats
WARNING
Passengers must always sit in a designat- ed seating area, place feet on the deck, and hold on to the handgrips when the boat is in motion.
This boat is equipped with the following seats.
Leaning post
The leaning post is a seat that is located in the center of the boat.
There is a cooler box under the leaning post.
     1
2 3
           2 1
      3
1 Front starboard seat
2 Front console seat
3 Front port seat
1 Strap
2 Leaning post
3 Cooler box
The leaning post for these models is equipped with a backrest. The position of the backrest can be changed by pulling the strap toward the bow or toward the stern. By mov- ing the backrest, you can change the seating position of the leaning post to face the bow or face the stern.
Jump seats
The 2 jump seats are located on the port and starboard sides of the boat near the stern.
   1
23
               1
2
           1 Jump seat (starboard)
2 Leaning post
3 Jump seat (port)
55
1 Jump seat (starboard)
2 Jump seat (port)
]]></page><page Index="63" isMAC="true"><![CDATA[ Removable backrest
This boat has 2 removable backrests.
Equipment operation
Engine hood
The engine hood can be opened to access the engine.
The engine hood latches are located under the front of the leaning post.
To open the engine hood, pull the engine hood latches up and lift the engine hood. NOTICE: 210FSH DELUXE: Do not open the engine hood while the anchor light is installed. Otherwise, the anchor light could be damaged.
    1
              2
         1
1 Backrest
    1
          1 Backrest
1 Engine hood latch
2 Engine hood
To close the engine hood, push the leaning post to securely lock it in place.
56
]]></page><page Index="64" isMAC="true"><![CDATA[Equipment operation
Storage compartments
This boat is equipped with the following con- venient on-board storage compartments. Make sure that the storage compartments are securely closed before getting underway.
Anchor storage compartment
The anchor storage compartment is located at the bow.
To open the anchor storage compartment:
To close the anchor storage compartment:
(1) Close the anchor storage compartment
lid.
(2) Turn the lock handle counterclockwise
and make sure that the lid is securely
closed.
(3) Push the lock handle down.
Bow storage compartment
The bow storage compartment is located un- der the front port seat.
To open a bow storage compartment: Unhook the latch, and then open the front port seat.
   (1) (2)
Pull the lock handle up.
Turn the lock handle clockwise and then open the anchor storage compartment lid.
  1
 2
 2
1
1 2
Lock handle
Anchor storage compartment lid
1 Front port seat 2 Latch
 1
 1
1
Anchor storage compartment
1 Bow storage compartment
When storing the anchor, place some cush- ioning material or the anchor line under the anchor.
57
]]></page><page Index="65" isMAC="true"><![CDATA[ To close the bow storage compartment: Close the front port seat, and then hook the latch on to the deck.
Insulated fish box
The fish box is located under the front star- board seat. It is insulated, and can be filled with some ice to help keep fish cold while boating. The box is self-draining.
To open the fish box:
Unhook the latch, and then open the front starboard seat.
Equipment operation
Stern storage compartment
The stern storage compartment is located under the jump seat (starboard).
To open the stern storage compartment: Unhook the latch, and then open the stern storage compartment lid.
    1
2
        1
 2
1 Stern storage compartment lid 2 Latch
 1
1 Front starboard seat 2 Latch
 1
1 Stern storage compartment
To close the stern storage compartment: Close the stern storage compartment lid, and then hook the latch on to the deck.
 1 Fish box
To close the fish box:
Close the front starboard seat, and then hook the latch onto the deck.
 58
]]></page><page Index="66" isMAC="true"><![CDATA[Equipment operation
Lockable storage compartment
The lockable storage compartment is located on the bow side of the console.
The lockable storage compartment has a large compartment suitable for use as an on- board changing room and can also accom- modate a portable toilet (not included). WARNING! Do not open the lockable stor- age compartment while the boat is mov- ing. The lockable storage compartment lid could block your vision of others. In addi- tion, the lockable storage compartment lid could close unexpectedly due to the movement of the boat and you could be pinched. Carbon monoxide (CO) can cause brain damage or death. Carbon monoxide can be present in this compart- ment. Signs of carbon monoxide poison- ing include nausea, headache, dizziness, drowsiness, and lack of consciousness. Get fresh air if anyone shows signs of car- bon monoxide poisoning.
To open the lockable storage compartment: While pulling the lockable storage compart- ment latch, lift the lockable storage compart- ment lid.
1 Lockable storage compartment
To use the lockable storage compartment light:
      1
         (1)
To turn on the lockable storage compart- ment light, push the light.
    1
              1
2
 1
Lockable storage compartment light
(2)
To drain water from the lockable storage compartment:
(1) Remove the drain plug on the bottom of
the lockable storage compartment to drain the water.
To turn off the light, push the light again.
  1 Lockable storage compartment lid
2 Lockable storage compartment latch
59
]]></page><page Index="67" isMAC="true"><![CDATA[Equipment operation
To unlock the lockable storage compartment: Insert the lockable storage compartment key into the keyhole of the lockable storage com- partment latch, and then turn the key 90° counterclockwise.
Curtain/curtain rails
The curtain can be installed when the lock- able storage compartment is open.
To install the curtain:
             1
    1
(2)
Drain plug
Securely install the drain plug in its origi-
(1)
Insert the curtain into the curtain rails.
       1
      2
         nal position.
To close the lockable storage compartment: Push the lockable storage compartment lid down to securely lock it in place.
To lock the lockable storage compartment:
(1) Close the lockable storage compart-
ment.
(2) Insert the lockable storage compartment
key into the keyhole of the lockable stor- age compartment latch, and then turn the key 90° clockwise.
Curtain rail
  1
2 Curtain
(2)
Snap the buttons on the curtain onto the button bases on the lockable storage compartment.
   1
2
                 1
         1
  1 Lockable storage compartment key
2 Keyhole
TIP:
Store the lockable storage compartment key so that it is not lost.
1
Button base
60
]]></page><page Index="68" isMAC="true"><![CDATA[Equipment operation
To remove the curtain:
(1) Unsnap the buttons on the curtain from
the button bases.
(2) Remove the curtain from the curtain rails.
Enclosed storage compartment (port)
The enclosed storage compartment is a large storage compartment that is located on the port side of the boat.
To open the enclosed storage compartment: Pull the enclosed storage compartment door latch to open the door.
Enclosed storage compartment (star- board)
The enclosed storage compartment is a large storage compartment that is located on the starboard side of the boat.
To open the enclosed storage compartment: Pull the enclosed storage compartment door latch to open the door.
    1
2
   1
2
1 Enclosed storage compartment door
2 Enclosed storage compartment door latch
1 Enclosed storage compartment door latch
2 Enclosed storage compartment door
 1
       1
 1 Enclosed storage compartment
To close the enclosed storage compartment: Close the enclosed storage compartment door, and then push it to securely lock it in place.
1 Enclosed storage compartment
To close the enclosed storage compartment: Close the enclosed storage compartment door, and then push it to securely lock it in place.
 61
]]></page><page Index="69" isMAC="true"><![CDATA[Equipment operation
 Glove compartment
The glove compartment is located under the steering wheel.
To open the glove compartment:
Pull the glove compartment latch to open the glove compartment lid.
  1
2
         1
2
    1 Glove compartment lid
2 Glove compartment latch
1 Keyhole
2 Glove compartment key
TIP:
Store the glove compartment key so that it is not lost.
To unlock the glove compartment:
Insert the glove compartment key into the keyhole of the glove compartment latch, and then turn the key 90° counterclockwise.
Storage pocket
The storage pocket is located on the star- board side of the glove compartment.
The storage pocket is equipped with an aux- iliary input jack and USB terminal for the ste- reo system, and a 12 V DC outlet.
              1
         2
3
4
12V
 1
1 Glove compartment
To close the glove compartment:
Close the glove compartment lid, and then push it to securely lock it in place.
To lock the glove compartment:
(1) Close the glove compartment.
(2) Insert the glove compartment key into
the keyhole of the glove compartment latch, and then turn the key 90° clock- wise.
1 Storage pocket
2 12 V DC outlet
3 Auxiliary input jack
4 USB terminal
  62
]]></page><page Index="70" isMAC="true"><![CDATA[Equipment operation
Wet storage compartment
The wet storage compartment is located un- der the swim platform.
To open the wet storage compartment:
(1) Pull the lock handle up.
(2) Turn the lock handle clockwise, and then open the rear platform hatch.
Bucket storage compartment
The bucket storage compartment is located in the center of the boat at the bow.
 1 Rear platform hatch
2 Lock handle
1 2
Bucket storage compartment lid Lock handle
To (1) (2)
open the bucket storage compartment: Pull the lock handle up.
Turn the lock handle, and then open the bucket storage compartment lid.
        1
2
                          1
2
       1
                 1
    1 Wet storage compartment
To close the wet storage compartment:
(1) Close the rear platform hatch.
(2) Turn the lock handle counterclockwise and make sure that the hatch is securely
closed.
(3) Push the lock handle down.
TIP:
The engines will not start if the rear platform hatch is not securely closed.
1
To (1)
Bucket storage compartment
drain the bucket storage compartment: Remove the drain plug on the bottom of the bucket storage compartment to drain the water.
  63
]]></page><page Index="71" isMAC="true"><![CDATA[Equipment operation
          1
             1
  1 Drain plug
(2) Securely install the drain plug in its origi- nal position.
To close the bucket storage compartment:
(1) Close the rear platform hatch.
(2) Turn the lock handle and make sure that
the hatch is securely closed.
(3) Push the lock handle down.
Rod holders
This boat is equipped with rod holders on the port and starboard sides of the console.
1 Rod holder
  1
  1
1
  1 Rod holder
          1
      1
  1
 1
1 Rod holder
1 Rod holder
64
]]></page><page Index="72" isMAC="true"><![CDATA[Equipment operation 210FSH SPORT
   1
     1
1
1 Rod holder
Livewell
The livewell for holding live bait and fish is lo- cated on the starboard side of the boat at the stern.
To open the livewell:
1 Livewell
To supply water to the livewell:
(1) Push the livewell switch to turn on the
livewell pump and supply water.
(2) When there is sufficient water in the livewell, push the livewell switch to turn
off the livewell pump.
(3) If necessary, push the aerator switch to
aerate and circulate the water in the livewell. (See page 52.)
  Pull the latch to open the livewell lid.
 1
2
  MNL
AERATOR
AUTO
LIVEWELL BILGE HORN
12
1 Livewell lid 2 Latch
1 Aerator switch
2 Livewell switch
TIP:
Push the courtesy light switch to turn on the livewell light.
To drain water from the livewell:
(1) Remove the drain plug on the bottom of
the livewell to drain the water.
 65
]]></page><page Index="73" isMAC="true"><![CDATA[Equipment operation
     1
        1
2
    1 Drain plug
(2) Securely install the drain plug in its origi- nal position.
To close the livewell:
Close the livewell lid, and then push it to se- curely lock it in place.
Battery compartment
WARNING
Do not carry any flammable substances in the compartment or any heavy or metal items that can damage the battery or cause a short circuit. Sparks or fire could result.
The battery compartment is located on the port side of the boat at the stern.
To open the battery compartment:
Unhook the latch, and then open the battery compartment lid.
1 Battery compartment lid 2 Latch
      1
        1 1 Battery compartment
To close the battery compartment:
Close the battery compartment lid, and then hook the latch onto the deck.
   66
]]></page><page Index="74" isMAC="true"><![CDATA[Equipment operation
Windshield
The windshield is removable. To remove the windshield:
(1) Turn the lock knobs counterclockwise
and remove them.
(2) Remove the windshield.
Anchor light (210FSH SPORT)
The anchor light is located at the top of the T- top. It is also the “all-around” light for naviga- tion at night or in low-visibility conditions. (See page 50 for information on the anchor light on.)
To use the anchor light:
Pull the lock tab, raise the anchor light, and then move the lock tab to its original position to lock the anchor light in place.
         2
1
2
              2
   1
  1 Windshield 2 Lock knob
To install the windshield:
(1) Place the windshield in its original posi-
tion.
(2) Securely install the lock knobs by turning
them clockwise.
1 Lock tab
To store the anchor light:
Pull the lock tab, lower the anchor light, and then move the lock tab to its original position to lock the anchor light in place.
  67
]]></page><page Index="75" isMAC="true"><![CDATA[ Anchor light
(210FSH DELUXE)
The boat is equipped with a removable an- chor light. It is also the “all-around” light for navigation at night or in low-visibility condi- tions. (See page 51 for information on the an- chor light on.)
The anchor light is stored in the lockable stor- age compartment.
To set up the anchor light:
(1) Open the lockable storage compart-
ment. (See page 59.)
(3)
Equipment operation
Slide anchor light stoppers A and B apart to disconnect them.
 2
         1
 1 2
Anchor light stopper A Anchor light stopper B
     1
        (4) Extend the anchor light pole, and then screw anchor light stopper A onto the center section of the pole.
    1
1 Lockable storage compartment
(2) Remove the anchor light from the anchor
light holder.
          21
  1 Anchor light holder
2 Anchor light
1 Anchor light stopper A
68
]]></page><page Index="76" isMAC="true"><![CDATA[Equipment operation
(5) Open the cap of the anchor light socket, fit the protrusion on the anchor light into the slot in the socket, and then install the light into the socket.
To store the anchor light:
(1) Pull anchor light stopper B upward, re-
move the anchor light, and then close the
cap of the anchor light socket.
(2) Unscrew anchor light stopper A from the center section of the anchor light pole,
and then fold the pole.
(3) Connect the stoppers by fitting the pro-
trusion on anchor light stopper A into the slot in anchor light stopper B.
         1
3
2
 2
1
         1 Cap
2 Slot
3 Protrusion
(6)
Fit anchor light stopper B into the anchor light socket.
   1
    1
Anchor light stopper B
69
1 Anchor light stopper A 2 Anchor light stopper B
(4) Install the anchor light into the anchor light holder, and then close the lockable storage compartment.
]]></page><page Index="77" isMAC="true"><![CDATA[Swim platform
WARNING
Stay away from the swim platform area while the engine is running. Exhaust gases coming from underneath it contain carbon monoxide, a colorless, odorless gas which may cause brain damage or death when inhaled. Symptoms include nausea, dizzi- ness, and drowsiness.
The swim platform area provides a place to stand or sit while putting on skis or a wake- board, and includes a ladder to make board- ing from the water easier.
1 Ladder
(2) Pull the ladder out completely, and then
lower it.
Equipment operation
    1
                       1
  1 Swim platform
Ladder
The ladder is stored under the swim platform. To use the ladder:
(1) Lift the end of the ladder to release it
from the hooks on the boat.
To stow the ladder:
(1) Raise the ladder until it is horizontal, and
then push it forward completely.
(2) Push the end of the ladder to fit it onto
the hooks on the boat.
     1
1 Hook
70
]]></page><page Index="78" isMAC="true"><![CDATA[Equipment operation
Jet wash
WARNING
The jet wash system must be used only by a passenger who is not operating the boat. While the jet wash system is being used, the boat operator must attach the engine shut-off cord (lanyard) to their PFD and scan constantly for people, objects, and other watercraft.
NOTICE
  If the jet wash system will not be used for an extended period, turn the shut-off valve to the closed position. To prevent water from freezing in the jet wash hos- es when storing the boat in freezing temperatures, drain the water from the hoses. For more information, contact a Yamaha Boat Dealer. Before using the jet wash system, make sure that the shut-off valve is in the open position. If water leaks from the hose fitting or coil hose or if you notice any other problem, turn the shut-off valve to the closed po- sition immediately.
  Whilethejetwashsystemisbeingused, scan constantly for people, objects, and other watercraft. Otherwise, the boat could collide with another watercraft, a dock, or other obstacle.
  210FSH DELUXE: Before using the jet wash system, make sure that the anchor light socket is closed. If the anchor light socket is not closed and water enters the socket, the socket could malfunc- tion.
The hose fitting for the coil hose is located on the deck near the jump seat (starboard).
1 Hose fitting
To use the jet wash:
(1) Connect the coil hose to the hose fitting.
   1
             2
  1
1 Coil hose
2 Hose fitting
(2) Start the engines. (See page 96.) (3) Push the jet wash switch.
  JET 1 WASH
 71
1 Jet wash switch
]]></page><page Index="79" isMAC="true"><![CDATA[ TIP:
  The water supply will start 5 seconds after the jet wash switch is pushed.
  The water flow can be adjusted to 3 levels. Push the jet wash switch to adjust the wa- ter flow level.
Equipment operation
(4) Move the jet wash handle lever to dis- charge water.
 1
         JET 1 WASH
            1 Jet wash switch
1 Jet wash handle lever
To stop using the jet wash:
(1) Push the jet wash switch.
(2) Stop the engines. (See page 98.)
(3) Push the collar on the hose fitting inward,
and then disconnect the coil hose from the fitting.
   10:27 am
12.3V
 FUEL 100%
0
0.3 Avg MPG
WATER 67°F
12.3V
MPH
 Jet Wash Mode 1
           1
1 Hose fitting
To turn the water supply on or off:
(1) Stop the engines. (See page 98.)
(2) Open the rear platform hatch. (See page
63.)
 72
]]></page><page Index="80" isMAC="true"><![CDATA[Equipment operation
 (3)
Remove the inspection cover.
T-top (210FSH SPORT)
The bimini top can be installed to use the T- top as a sunshade or rain cover for the leaning post. (See page 74 for bimini top removal and installation procedures.)
   1
        1
       1
(4)
Inspection cover
To turn on the water supply, turn the shut-off valve 90° clockwise.
       1
 1
(5)
(6) (7)
Shut-off valve
To turn off the water supply, turn the shut-off valve 90° counterclockwise. Install the inspection cover.
Close the rear platform hatch.
73
1 T-top
]]></page><page Index="81" isMAC="true"><![CDATA[ Bimini top (210FSH SPORT)
The T-top is equipped with a bimini top, which can be used as a sunshade or rain cov- er for the leaning post.
The bimini top can be removed and installed.
Equipment operation
(2) Loosen the ratchet, and then loosen the strap securing the bimini top.
 1
 1
           1 Bimini top
To remove the bimini top:
(1) Open the flap on the starboard side of
the bimini top.
1 Ratchet
(3) Slowly pull the bimini top toward the bow and remove it.
To install the bimini top:
When installing the bimini top, simply reverse the removal steps.
     1
1 Flap
74
]]></page><page Index="82" isMAC="true"><![CDATA[Equipment operation
Bimini top (210FSH DELUXE)
Setting up the bimini top
To set up the bimini top:
(3)
Remove the storage cover, unfold the bi- mini top, and pull it toward the stern.
  1
 (1)
Raise the bimini top.
   1
       1
(2)
Bimini top
Secure each forward support pole to the forward support pole mounting bracket using the lock pin.
1
(4)
Storage cover
Push each center pole up, and then in- stall the lock pin.
      1
               2
    1
3 2
 1
          1 2
Center pole Lock pin
 1 2 3
Forward support pole
Lock pin
Forward support pole mounting bracket
NOTICE
Do not exceed 72 km/h (45 mph) with the bimini top in the up position.
  75
]]></page><page Index="83" isMAC="true"><![CDATA[ Storing the bimini top in the upright position
NOTICE
Do not trailer the boat with the bimini top in the fully extended or upright storage po- sition. Put the bimini top in the fully col- lapsed position to avoid damage.
To store the bimini top in the upright position:
Equipment operation
Storing the bimini top in the fully collapsed position
To store the bimini top in the fully collapsed position:
(1) Follow the above steps for “Storing the
bimini top in the upright position”.
(2) While supporting the bimini top, remove the lock pins securing the forward sup- port poles to the forward support pole
mounting brackets.
      (1)
Remove the lock pins, and then push the center poles down.
   1
3 2
 1
                1
               2
 1 2
(2)
Center pole Lock pin
Pull the bimini top toward the bow.
1 Forward support pole
2 Lock pin
3 Forward support pole mounting bracket
(3) Lower the bimini top onto the rear deck.
        1
         1
(3)
Bimini top
Install the storage cover.
76
]]></page><page Index="84" isMAC="true"><![CDATA[Equipment operation
Trailering with the bimini top
The bimini top must be secured to the boat when it is being trailered. When the boat is trailered with a genuine Yamaha boat cover, simply store the bimini top in the fully col- lapsed position and install the boat cover. If a boat cover is not used, wrap an elastic cord around the top and secure the ends to the ski tow hook to restrict movement.
Removing the bimini top
To remove the bimini top:
(1) Store the bimini top. See “Storing the bi-
mini top in the fully collapsed position”.
(2) Remove the main pole mounting pins se- curing the bimini top to the main pole
mounting brackets.
      1
     1 Main pole mounting pin
(3) Remove the bimini top from the boat.
Installing the bimini top
To install the bimini top:
When installing the bimini top, simply reverse the removal steps, and then make sure that the main pole mounting pins are securely in- stalled.
 77
]]></page><page Index="85" isMAC="true"><![CDATA[Fuel
WARNING
Operation and handling requirements
 Fuel requirement
ethanol content does not exceed 10% and the fuel meets minimum octane ratings. E-85 is a fuel blend containing 85% ethanol and therefore must not be used in this boat. All ethanol blends containing more than 10% ethanol can cause fuel system damage or en- gine performance problems.
Yamaha does not recommend gasohol con- taining methanol because it can cause fuel system damage and engine performance problems.
    Gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions.
  Gasoline is poisonous and can cause in-
jury or death. Handle gasoline with care. Never siphon gasoline by mouth. If you To should swallow some gasoline, inhale a (1) lot of gasoline vapor, or get some gaso-
line in your eyes, see your doctor imme- diately. If gasoline spills on your skin, wash with soap and water. If gasoline (2) spills on your clothing, change your clothes.
fill the fuel tank:
Before refueling, turn off the engine. Nev- er refuel while smoking, or while in the vi- cinity of sparks, open flames, or other sources of ignition.
Refuel the boat in a well-ventilated area. If the boat is in the water, be sure it is se- curely moored to the fueling dock. All passengers must be out of the boat dur- ing refueling.
Press the fuel tank filler cap button, and then open the fuel tank filler cap.
   NOTICE
  Do not use leaded gasoline. Leaded gasoline can seriously damage the en- gine.
  Avoidgettingwaterandcontaminantsin the fuel tank. Contaminated fuel can cause poor performance and engine damage. Use only fresh gasoline that has been stored in clean containers.
(3)
                  1
2
        Recommended fuel:
Regular unleaded gasoline with a minimum octane rating of 86 (Pump octane number) = (R + M)/2 90 (Research octane number)
 Gasohol
There are two types of gasohol: gasohol con- taining ethanol and that containing methanol. Gasohol containing ethanol can be used if
Fuel tank capacity:
197 L (52.0 US gal, 43.3 Imp.gal)
1 2
(4)
Fuel tank filler cap
Fuel tank filler cap button
Slowly add fuel to the fuel tank.
  78
]]></page><page Index="86" isMAC="true"><![CDATA[Operation and handling requirements
 (5) Stop filling when the fuel just becomes visible in the bottom of the filler tube. Do not “top off” the tank, because gasoline could spill out.
(6) Wipe up any spilled fuel immediately.
(7) Close the fuel tank filler cap by pushing it until it locks in place. Make sure that the
fuel tank filler cap is securely closed.
Engine Med RX Fuel Additive
As the fuel mixture burns in your engine’s combustion chambers, carbon deposits are left behind. Over time, these deposits can re- duce performance and even cause engine damage. Marine engines tend to run at lower operating temperatures than other engines, making them more likely to accumulate these harmful deposits.
Engine Med RX, available from your Yamaha Boat Dealer, is formulated to remove existing deposits and, when used continuously, pre- vent new ones from forming, while also help- ing to keep fuel injectors and other fuel system components clean for proper perfor- mance and longer engine life.
Engine oil requirement Engine oil
NOTICE
Use only 4-stroke engine oil. Usage of 2- stroke engine oil could result in severe en- gine damage.
Select an oil grade according to the average temperatures in the area where the boat will be used.
      Recommended engine oil: YAMALUBE 4W
Recommended engine oil type: SAE 10W-30, 10W-40, 20W-40, 20W-50
Recommended engine oil grade: API SG, SH, SJ, SL
  79
TIP:
When the engine is operated at high speeds, some engine oil may be consumed. Be sure to check the engine oil level.
Why Yamalube
YAMALUBE oil is a Genuine YAMAHA Part born of the engineers’ passion and belief that engine oil is an important liquid engine com- ponent. We form teams of specialists in the fields of mechanical engineering, chemistry, electronics and track testing, and have them develop the engine together with the oil it will
]]></page><page Index="87" isMAC="true"><![CDATA[Operation and handling requirements
 use. Yamalube oils take full advantage of the base oil’s qualities and blend in the ideal bal- ance of additives to make sure the final oil clears our performance standards. Thus, Yamalube mineral, semisynthetic and syn- thetic oils have their own distinct characters and value. Yamaha’s experience gained over many years of research and development into oil since the 1960’s helps make Yamalube the best choice for your Yamaha engine.
water.)
  When checking the engine oil level on wa-
ter, moor the boat so that it will not drift away.
To check the engine oil level:
(1) With the engine stopped, place the boat
in a precisely level position on land or
launch the boat.
(2) Look in all directions, and then start the
engine. (See page 96 for information on
starting the engine.)
(3) Run the engine at idling speed for 6 min-
utes or more. Run the engine an addi- tional 5 minutes if the ambient temperature is 20 °C (68 °F) or less.
(4) Stop the engine.
(5) Open the engine hood. (See page 56.) (6) Loosen the oil tank filler cap and remove
it, and then wipe the attached dipstick clean.
            Checking the engine oil level
WARNING
Engine oil is extremely hot immediately af- ter the engines are turned off. Coming in contact with or getting any engine oil on your clothes could result in burns.
NOTICE
  Do not run the engine with too much or not enough oil in the oil tank, otherwise the engine could be damaged.
  Make sure that debris and water do not enter the oil tank filler hole. Debris and water in the engine oil can cause serious engine damage.
TIP:
  Whencheckingtheengineoillevelonland, the engine must be running while water is being supplied to the cooling water pas- sages. (See “Flushing the cooling system” on page 111 for information on supplying
1 Oil tank filler cap/Dipstick
(7) Screw the oil tank filler cap into the filler hole until it stops. Remove the oil tank filler cap again and make sure that the engine oil level is between the minimum and maximum level marks.
            1
       80
]]></page><page Index="88" isMAC="true"><![CDATA[Operation and handling requirements
   123
  1 Dipstick
2 Maximum level mark
3 Minimum level mark
Draining the bilge water
NOTICE
  Do not run the engines at full throttle when bilge water remains in the engine compartment. The bilge water can splash into the engines, which can result in severe damage.
  Be sure all drain plugs are tightened be- fore operating your boat. Otherwise, water may flood the boat and cause it to submerge.
Draining the bilge water on land
This model is equipped with multiple drain plugs.
Bilge water from the various compartments flows through drain passages and collects in the bottom of the hull. The bilge water can be drained from the boat by removing the hull drain plug.
Lockable storage compartment
 (8)
(9)
If the engine oil level is significantly above the maximum level mark, consult a Yamaha Boat dealer. If the engine oil level is below the minimum level mark, slowly add engine oil.
Repeat steps (6)–(8) until the engine oil is
at the proper level.
(10) Securely install the oil tank filler cap and
turn it until it stops.
(11) Repeat the checking oil level procedure
for the other engine.
(12) Close the engine hood.
            1
  81
1 Drain plug
]]></page><page Index="89" isMAC="true"><![CDATA[Operation and handling requirements
 Engine compartment
while the boat is moored or moving in re- verse.
Bilge pump
Your boat is equipped with a drainage sys- tem that channels water that enters the boat from the storage compartments to the bilge under the engine compartment.
When the bilge pump switch is turned on, the bilge pump will operate.
   1
                       LIVEWELL BILGE HORN
1
        1 Fuel tank compartment drain plug
To drain the bilge water from the hull: Remove the hull drain plug at the stern to drain the water. Check the condition of the O-ring on the hull drain plug, and then se- curely install the drain plug.
                 1
1 Hull drain plug
Draining the bilge water on water
This model is equipped with a self-draining deck and bilge pump to drain the bilge water on water.
Self-draining deck
Most water that enters the deck area drains automatically out the stern through the large drain holes in the deck.
A one-way check valve in each drain pre- vents water from traveling back to the deck
1 Bilge pump switch
Even if the bilge pump switch is not turned on, the bilge pump will detect when there is excessive water in the bilge and will automat- ically drain most of it through the bilge pump outlet. This function works automatically, even if the battery switches are turned to the off position.
     1
 1 Bilge pump outlet
82
]]></page><page Index="90" isMAC="true"><![CDATA[Operation and handling requirements
 TIP:
  The bilge pump indicator light comes on while the bilge pump is operating.
       LIVEWELL BILGE HORN
          When the bilge pump operates automati- cally, the bilge pump will not stop until most of the bilge water is drained.
83
]]></page><page Index="91" isMAC="true"><![CDATA[First-time operation
 Engine break-in
NOTICE
Failure to perform the engine break-in could result in reduced engine life or even severe engine damage.
The engine break-in period is essential to al- low the various components of the engines to wear and polish themselves to the correct operating clearances. This ensures proper performance and promotes longer compo- nent life.
(1) Check the engine oil level. (See page 80 for information on checking the engine oil level.)
(2) Launch the boat and start the engines. (See page 96 for information on starting the engines.)
(3) For the first 5 minutes, operate with the engines at idling speed.
(4) For the next 30 minutes, operate with the engines speed below 5000 r/min.
(5) For the next 1 hour, operate with the en- gines speed below 6500 r/min.
After the engine break-in is complete, the boat can be operated normally.
   84
]]></page><page Index="92" isMAC="true"><![CDATA[Pre-operation checks
  WARNING
Failure to inspect or maintain the boat properly increases the possibility of an accident or damage to the boat. Do not operate the boat if you find any problem.
If a problem cannot be corrected by the procedures provided in this manual, have the boat inspected by a Yamaha Boat Dealer.
Pre-operation checklist
Before operating this boat, perform the checks in the following checklist. Always follow the in- spection and maintenance procedures and schedules described in this owner’s/operator’s man- ual.
Pre-operation checks should be made each time the boat is used. These checks can be com- pleted in a short time. It is worth the time spent to ensure safety and reliability.
   ITEM CHECK PAGE
  PRE-LAUNCH CHECKS
 Steering system
Check for proper steering operation.
87
Remote control levers
Check for proper throttle operation. Check for proper shift operation.
87
Fire extinguisher
Check readiness of the extinguisher.
88
Hull
Check hull for damage and cracks before launching.
—
Access port cap
Check for proper installation.
89
Jet intakes
Check that no debris is in the intake before launching.
90
Fuel system
Check fuel system for leaks.
90
Engine oil level
Check engine oil level; add as necessary.
80
Battery
Check battery condition, mounting, and connection.
91
Bilge water
Check the engine compartment for bilge water.
91
Drain plugs
Check the drain plugs for damage and foreign material and check that they are securely installed.
91
Engine compartment and blowers
Open the engine hood and check to be sure no gasoline, gasoline vapors, or loose electrical connections are present. Operate the blowers for at least 4 minutes.
92
Engine hood
Check that the hood latches are secure.
56
Lights and horn
Check lights to be sure they operate. Push the horn switch to be sure it operates.
92, 93
Bimini top
Check that the top is secure.
74, 75
Engine shut-off cord (lan- yard)
Check the engine shut-off cord (lanyard) for damage.
93
T-top (210FSH SPORT)
Check that the T-top screws and nuts are secured.
73
                     85
]]></page><page Index="93" isMAC="true"><![CDATA[Pre-operation checks
  ITEM CHECK PAGE
  POST-LAUNCH CHECKS
 Switches
Check operation of the main switches and engine shut- off switch.
94
Cooling water pilot outlets
Check that water comes out while the engines are run- ning.
94
Fuel level
Check fuel level; add as necessary.
94
       The steering and shifting pre-operation checks will require two persons: one person to oper- ate the controls and one person to observe the proper operation at the stern.
86
]]></page><page Index="94" isMAC="true"><![CDATA[Pre-operation checks
Pre-operation check points Pre-launch checks
Perform the pre-launch checks in the pre-op- eration checklist while the boat is on land.
Steering system checks
Make sure the steering wheel is not loose. There should not be any free play, either in- and-out or in rotation. Turn the steering wheel fully to the right and left to make sure opera- tion is smooth and unrestricted throughout the whole range.
1 Jet thrust nozzle 2 Articulating keel
Remote control lever checks
WARNING
Do not touch the shift gates while the re- mote control levers are being operated, otherwise, you could be pinched.
Operate the remote control levers several times to make sure that operation is smooth throughout the whole range.
            11 2
                             Make sure both the jet thrust nozzles change directions as the steering wheel is turned. The jet thrust nozzles should point to star- board (right) when the wheel is turned to the right. The jet thrust nozzles should point to port (left) when the wheel is turned to the left. There should not be free play between the steering wheel and the jet thrust nozzles. In addition, check that the direction of the artic- ulating keel changes according to the move- ment of the jet thrust nozzles.
1 Neutral position 2 TDE position
3 Forward position 4 Reverse position 5 Shift
6 Fully closed 7 Throttle
8 Fully open
 F2 N1 R 55
34
77 66
88
87
]]></page><page Index="95" isMAC="true"><![CDATA[ Check that the shift gates are slightly above the shift gate neutral position when the re- mote control levers are in the forward posi- tion, and that the shift gates are in the fully open position when the remote control levers are moved farther forward.
Fully open position
Pre-operation checks
fire extinguisher whenever the boat is operat- ed.
Make sure at least one fire extinguisher is aboard and full; two fire extinguishers are recommended. See the instructions supplied by the extinguisher manufacturer to deter- mine the indication of the condition.
A fire extinguisher is not standard equipment with this boat. If you do not have a fire extin- guisher, contact your local Yamaha Boat Dealer or fire extinguisher dealer for one meeting the proper specifications.
Storing the fire extinguisher
One fire extinguisher is to be mounted in the lockable storage compartment. The fire ex- tinguisher recommended for this location is a chemical-type extinguisher with a capacity of two pounds or more.
   1
1
             1 Shift gate
Check that the shift gates are in the fully closed position when the remote control le- vers are in the reverse position.
Fully closed position
                    11
           1 Shift gate
Fire extinguisher check
As an inboard boat less than 26 feet in length, your boat must be fitted with one 5-B (B-1) type fire extinguisher when navigating waters controlled by the U.S. Coast Guard. In addi- tion, most state and local boating laws re- quire that the craft carry a USCG-approved
If you choose to have two fire extinguishers, the other fire extinguisher is to be mounted in the battery compartment. There is a location label outside the compartment. This fire ex- tinguisher located near the engine compart- ment should be a “clean agent” type designed to displace oxygen, with an inert gas, such as CO2, or FE-36TM, and have a ca- pacity of five pounds or more.
88
]]></page><page Index="96" isMAC="true"><![CDATA[ Pre-operation checks
           Operating the fire extinguisher
A chemical-type fire extinguisher may not help when sprayed into the engine compart- ment through the FIRE-PORTTM because that type needs to be aimed directly at the base of the flames to be effective. See below for FIRE-PORTTM information.
A FIRE-PORTTM is mounted below the lean- ing post. Use this port to spray the contents of a fire extinguisher into the engine compart- ment if a fire breaks out in the engine area. WARNING! If there is a fire in the engine compartment, opening the hatch will add more oxygen to the fire, increasing the risk of a larger fire or an explosion.
If you see smoke or otherwise suspect a fire, you can look through the transparent flaps of the FIRE-PORTTM to look for signs of flames. If there is a fire, push the nozzle of the fire ex- tinguisher through the FIRE-PORTTM and fol- low the manufacturer’s instructions to empty the contents of the fire extinguisher into the engine compartment.
A “clean agent” type fire extinguisher is rec- ommended; a chemical-type fire extinguisher may not be adequate in this application.
Access port cap check
Make sure that the access port caps are se- curely installed.
To check the access port caps:
(1) Open the rear platform hatch. (See page
63 for information on the rear platform
hatch.)
(2) Make sure that the access port caps are
securely installed. If they are removed or are not locked, securely install them. (See page 126 for information on the ac- cess port caps.)
      1
        1 FIRE-PORTTM
   89
]]></page><page Index="97" isMAC="true"><![CDATA[  1
 1
(3)
Access port cap
Close the rear platform hatch.
Pre-operation checks
off the engines, remove the main switch key, and then remove the engine shut-off cord (lanyard) from the engine shut-off switch.
Fuel system checks
Check the fuel filler hoses and joints in the en- gine compartment for damage, looseness, and signs of leaking. At least annually, or if a problem is suspected, check the fuel tank and fuel filler hoses and clamps. Have a Yamaha Boat Dealer check the fuel tank and fuel filler hoses and clamps. WARNING! If there are signs of leaking fuel, do not op- erate the boat until the source of the fuel leak is found and corrected. Gasoline and its vapors are highly flammable and explo- sive.
Engine oil level check
Make sure that the engine oil level is between the minimum level mark and maximum level mark on the dipstick. (See page 80 for infor- mation on checking the engine oil level.)
Jet intake checks
Carefully check the jet intakes under the boat for weeds, debris, or anything else that might restrict the intake of water. If the intakes are clogged, cavitation could occur, reducing jet thrust, and possibly damaging jet pump parts.
      1
          1
   1 Jet intake
In some cases, the engines may overheat be- cause of a lack of cooling water, and damage could result. If the jet intakes are clogged, clean them. (See page 126 for information on the jet intakes.) WARNING! Rotating parts could cause severe injury or death. Before attempting to remove weeds or debris from the jet intakes or impeller areas; shut
1 Oil tank filler cap/Dipstick
90
]]></page><page Index="98" isMAC="true"><![CDATA[Pre-operation checks
   123
1 Dipstick
2 Maximum level mark
3 Minimum level mark
Battery check
Make sure that the battery terminals are not damaged and that the battery leads are con- nected properly. WARNING! The battery must always be fully charged and in good condition. Loss of battery power may leave you stranded. Never operate the boat if the battery does not have sufficient power to start the engines or if it shows any other signs of decreased power.
(See page 81 for information on draining the bilge water.)
Drain plug check
Loosen the drain plug and remove it, and then make sure that the plug and the O-ring on the hull drain plug is not damaged and that there is no foreign material on the threads or the O-ring on the hull drain plug. NOTICE: Before installing the drain plug, clean the drain plug threads and the O-ring on the hull drain plug to remove any foreign ma- terials, such as dirt or sand. Otherwise, the drain plug could be damaged, allowing water to enter the engine compartment. Make sure that the drain plug is tightened securely before launching the boat. Other- wise, water may flood the boat and cause it to submerge.
Securely install the drain plug by tightening it until it stop.
                   1
   2
1
        1
       1 Negative (–) battery terminal: Black lead
2 Positive (+) battery terminal: Red lead
Bilge water check
Make sure that no bilge water has collected in the engine compartment. If bilge water has collected in the engine compartment, drain it.
91
1 Hull drain plug
]]></page><page Index="99" isMAC="true"><![CDATA[ Blower switch check
WARNING
Gasoline vapors can explode. Before starting the engine, check the engine compartment for gasoline, gasoline va- pors, and loose electrical connections, and then operate the blower for at least 4 minutes. Do not start the engine or oper- ate the blower if you can smell gasoline vapors in the engine compartment or if there are any loose electrical connections. Contact a Yamaha Boat Dealer if there is a problem you cannot locate or correct.
Make sure that the blower operates properly when the blower switch is pushed.
Pre-operation checks
Push the blower switch to operate the blower and ventilate the engine compartment for at least 4 minutes.
Navigation and anchor lights switch check
Push the navigation and anchor lights switch and check that the bow light and anchor light come on.
(1) 210FSH DELUXE: Install the anchor light. (See page 68 for information on the an- chor light.)
(2) Push the upper side of the navigation and anchor lights switch and check that the bow light and anchor light come on.
     NAV/
ANC CTSY ACC ACC
1
LIGHTS
 1
BLOWER
 1 Blower switch
1 Navigation and anchor lights switch
     11
              1 Blower
92
]]></page><page Index="100" isMAC="true"><![CDATA[Pre-operation checks
 1 Anchor light 210FSH SPORT
1 Horn switch
Engine shut-off cord (lanyard) check
Make sure that the engine shut-off cord (lan- yard) is not damaged. If the cord is damaged, replace it. WARNING! Never try to repair the engine shut-off cord (lanyard) or tie it together. The engine shut-off cord (lan- yard) may not pull free when the operator falls off, allowing the boat to continue to run and cause an accident.
(4) Put the navigation and anchor lights switch in the middle position and check that the bow light and anchor light are off.
(5) 210FSH DELUXE: Remove the anchor light.
Horn switch check
Push the horn switch and check that the horn sounds.
 1
  MNL
AERATOR
AUTO
LIVEWELL BILGE HORN
1
1 Bow light 210FSH DELUXE
 1
  1
   1
(3)
Anchor light
Push the lower side of the navigation and anchor lights switch and check that only the anchor light comes on.
 93
]]></page><page Index="101" isMAC="true"><![CDATA[Pre-operation checks
 Post-launch checks
Perform the post-launch checks in the pre- operation checklist while the boat is in the water and the engines are running.
Engine shut-off switch check
Check the engine shut-off switch for proper operation.
(1) Start the engines. (See page 96 for infor-
mation on starting the engines.)
(2) Pull the engine shut-off cord (lanyard) to remove the clip from the engine shut-off switch to make sure that the engines
stop immediately.
(3) Make sure that the engines cannot be
started with the clip removed from the engine shut-off switch.
TIP:
It may take up to 20 seconds for water to reach the pilot outlets when first launching the boat. The amount and force of the exiting water will vary with engine speed.
NOTICE
A continuous flow of water from the pilot outlets shows that water is flowing through the engine cooling water passag- es. If water is not flowing out of the pilot outlets during operation, do not continue to run the engines. Overheating and seri- ous damage could occur. (See “Over tem- perature warning” on page 45 for more information.)
Fuel level check
Check the amount of fuel remaining in the fuel tank using the fuel level bar graph on the multi-function display.
                   1
2
          1 Engine shut-off switch 2 Clip
Cooling water pilot outlet check
Check that water comes out from the pilot outlets while the engines are running in the water. If water is not circulating, something may be clogging the intake grates. Refer to “Jet pump clean-out procedure” on page 126.
94
]]></page><page Index="102" isMAC="true"><![CDATA[Pre-operation checks
  1
    10:27 am
  FUEL 0 100%
12.3V
MP
0.3 Avg MPG
     H
1 Fuel level bar graph
Add fuel if necessary. (See page 78 for infor-
mation on filling the fuel tank.)
95
]]></page><page Index="103" isMAC="true"><![CDATA[Driving your boat Getting to know your boat
Operating your boat requires skills acquired through practice over a period of time. Take the time to learn the basic techniques well before attempting more difficult maneuvers. Boating with your new boat can be a very en- joyable activity, providing you with hours of pleasure. But it is essential to familiarize your- self with the operation of the boat to achieve the skill necessary to enjoy boating safely. Before operating this boat, read this own- er’s/operator’s manual, the Operation In- struction card, and all labels on the boat. Pay particular attention to the safety information beginning on page 10. These materials should give you an understanding of the boat and its operation. This boat is designed to carry one operator and up to 9 passengers.
Always attach the engine shut-off cord (lan- yard) to your PFD before operating.
You and all other passengers must always wear a USCG-approved PFD when riding in the boat.
Grip the steering wheel firmly and keep both feet on the deck when driving the boat.
Starting the engine
WARNING
Severe injury or death may result if you ig- nore any of the following:
  Before operating your boat, become fa-
miliar with all controls. Consult a Yamaha Boat Dealer about any control or function you do not fully understand. Failure to understand how the controls work could cause an accident or pre- vent you from avoiding an accident.
  Gasoline vapors can explode. Before starting the engines, check the engine compartment for gasoline, gasoline va- pors, and loose electrical connections, and then operate the blowers for at least 4 minutes. Do not start the engines or operate the blowers if you can smell gasoline vapors in the engine compart- ment or if there are any loose electrical connections. Contact a Yamaha Boat Dealer if there is a problem you cannot locate or correct.
Operation
       Maximum load:
Total weight of cargo, operator, and passengers:
1021 kg (2250 lb)
Total weight of operator and passen- gers:
844 kg (1860 lb)
 Learning to operate your boat
Before boating, always perform the pre-oper- ation checks listed on page 85. The short time spent checking the boat will reward you with added safety and reliability.
Know and follow U.S. Coast Guard, state, and local laws when operating your boat. Select a wide area to learn in, where visibility is good and other boat traffic is light. Keep the proper distance from other boats and ve- hicles. Do not operate where people are swimming.
96
]]></page><page Index="104" isMAC="true"><![CDATA[Operation
  Attachtheengineshut-offcord(lanyard) to your PFD before operating. Failure to attach the cord could result in a run- away boat if the operator is ejected.
  Do not apply throttle when anyone is at the rear of the boat. Turn the engines off or keep it at idle. Water and debris exit- ing the jet thrust nozzle can cause se- vere injury.
(1) Always make sure the boat is launched and used in waters that are free from weeds and debris, and at least 90 cm (3 ft) deep from the bottom of the boat. WARNING! Never operate in water that is less than 90 cm (3 ft) deep from the bottom of the boat. You increase your chance of hitting an underwater obstacle. You could be injured. Peb- bles or sand can also be sucked into the jet intakes, damaging the impel- lers.
NOTICE
There is a hull drain plug at the bottom of the stern. Check the O-ring on the hull drain plug and make sure that the plug is tightened securely before launching the boat. Otherwise, water may flood the boat and cause it to submerge.
1 Hull drain plug
(2) Turn the battery switch to the ON posi- tion.
(3) Push the blower switch to operate the blowers and ventilate the engine com- partment for at least 4 minutes.
                  1
  1
BLOWER
   90 cm (3 ft)
1 Blower switch
(4) Attach the engine shut-off cord (lanyard) to your PFD. Install the clip onto the en- gine shut-off switch by pushing the clip groove over the nut beneath the knob. Be sure the cord is not wrapped around the steering wheel or tangled in the con- trols. WARNING! Check that the en- gine shut-off cord (lanyard) is attached correctly. If the engine shut- off cord (lanyard) is not attached cor- rectly, it may not pull free when the operator falls off, allowing the boat to
   97
]]></page><page Index="105" isMAC="true"><![CDATA[continue to run and cause an acci- dent.
NOTICE
  Never turn the main switch keys to the start position while the engines are run- ning. The starter mechanism could be damaged.
  If the starter motors are engaged con- tinuously for more than 5 seconds, the battery will become quickly discharged and it will be impossible to start the en- gines. The starter motors may also be damaged if they are engaged continu- ously for more than 5 seconds.
On this boat, the engines are connected di- rectly to the drive units. Starting either engine generates some thrust immediately. Only enough throttle should be applied to keep the engine at a fast enough idle to stay running.
Stopping the engines
WARNING
Once the engines has stopped, you have NO STEERING CONTROL over the boat. You could collide with another boat, a dock, or other obstacle.
Stopping the engines immediately after oper- ating at high engine speeds is not recom- mended. Let the engines cool off at idle or low speed for a few minutes first.
To stop the engines:
(1) Return the remote control levers to the
neutral position.
(2) Turn the main switch key to the off posi-
tion.
Operation
            1
   2
3
      1 Engine shut-off switch
2 Clip
3 Engine shut-off cord (lanyard)
TIP:
The engines will not start when the clip is re- moved from the engine shut-off switch. The starter motors will turn over without the cord attached.
(5) Put the remote control levers in the neu- tral position. The starter motors will not operate unless the remote control levers are in neutral.
(6) Turn the main switch keys to the start po- sition and release it when the engines start. If the engines do not start after 5 seconds of cranking, release the keys. Wait at least 15 seconds before trying to start the engines again.
      BLOWER
 98
]]></page><page Index="106" isMAC="true"><![CDATA[Operation
   BLOWER
  TIP:
The engines can also be stopped by pulling the engine shut-off cord (lanyard).
(3) Remove the main switch keys and the
engine shut-off cord (lanyard) if the boat will be left unattended.
Leaving a dock
Because boats steer from the stern, the stern first moves in the direction opposite your de- sired turn. It is especially important to under- stand this characteristic when leaving a dock. If you move the remote control levers to the forward position and simply turn the steering wheel to steer the bow away from the dock, as you would when driving a car out of a parking space, you will drive the stern of the boat into the dock.
The following steps are basic maneuvering techniques which can be used in most cir- cumstances:
(1) With the engines idling and the bow still
moored to the dock, turn the steering wheel toward the dock. Moving the re- mote control levers into the TDE position or forward position will start to move the stern of the boat away from the dock.
(2) When the stern is out a few feet, release the bow mooring, and then turn the steering wheel to the center position or away from the dock. Move the remote
control levers into the reverse position and move away from the dock.
Turning the boat
WARNING
  Do not pull the remote control levers back to idle when trying to steer away from objects — you need throttle to steer.
  Be sure passengers are holding on be- fore making turns. An unprepared pas- senger could lose balance and fall.
Steering control depends on the combination of steering wheel position and the amount of throttle.
Water sucked in through the intake grate is pressurized by the impeller in the jet pumps. As the pressurized water is expelled from the pumps through the jet thrust nozzles, it cre- ates thrust to move and steer the boat. The higher the engine speed, the more thrust is produced.
The amount of jet thrust, in addition to the po- sition of the steering wheel, determines how sharply you turn.
A. More throttle produces high thrust, so
the boat will turn more sharply.
  A
      99
]]></page><page Index="107" isMAC="true"><![CDATA[ B. Less throttle produces low thrust, so the boat will turn more gradually.
Operation
are stopped, the boat will go straight even though the steering wheel is turned. You need throttle to steer.
 B
      D
     C. Pulling the remote control levers back to idle or neutral position produces only minimum thrust. If you are traveling at speeds above trolling, you will have rap- idly decreasing ability to steer without throttle. You may still have some turning ability immediately after pulling the re- mote control levers back to idle, but when the engines slows down, the boat will no longer respond to steering wheel input until you apply throttle again or you reach a trolling speed.
At trolling speed, the boat can be turned gradually by steering wheel position alone using just the amount of thrust available at engine idle.
Turning left
                Turning right
       C
              D. If the boat is moving and the remote con- trol levers are in neutral position, or if there is no thrust because the engines
100
]]></page><page Index="108" isMAC="true"><![CDATA[Operation
Boating with passengers
WARNING
When passengers are on board, make sure they are seated and holding onto the handgrips before you start to accelerate. An unprepared passenger could lose bal- ance and fall.
Your boat is designed for one operator and up to 9 passengers only. Never have more than 10 people in the boat. Passengers must sit in one of the seats and hold onto the hand- grips. Passengers should sit so the weight in the boat is balanced from side-to-side and bow-to-stern as much as possible. If the pas- senger seat in front of the helm is used, be sure the operator’s view ahead is not ob- structed.
  You will lose steering control if you com- pletely pull the throttle back to idle. You need throttle to steer.
  Do not use the reverse function to slow down or stop the boat from planing speed as it could cause you to lose con- trol, be ejected, or impact the steering wheel or other parts of the boat. This could increase the risk of serious injury.
The boat is not equipped with a separate braking system. It is stopped by water resis- tance after the remote control levers are moved back to idle. From full speed, the boat stops in approximately 115 m (377 ft) after the remote control levers are moved back to idle. The stopping distance varies depending on gross weight, water surface conditions, and wind direction. The stated straight-line stopping distance should be used for a refer- ence. The boat slows down as soon as the remote control levers are returned to idle but will coast for a distance before fully stopping. If you are not sure you can stop in time before hitting an obstacle, apply throttle and turn in another direction.
        Maximum load:
Total weight of cargo, operator, and passengers:
1021 kg (2250 lb)
Total weight of operator and passen- gers:
844 kg (1860 lb)
  115 m (377 ft)
      Stopping the boat
WARNING
  Allow adequate stopping distance.
  Takeearlyactiontoavoidcollisions.Re-
member, boats do not have brakes.
  Operate defensively at safe speeds and keep a safe distance away from people, objects, and other boats to give you time
to stop.
  Do not shut the engine off when slowing
down in case you need engine power to steer away from a boat or other obstacle that comes into your path.
  101
]]></page><page Index="109" isMAC="true"><![CDATA[Boarding from the water
WARNING
To avoid severe injury or death, do not board from the rear, use swim platform, or swim behind boat if engines are running.
  Severe internal injuries can occur if wa-
ter is forced into body cavities as a re-
sult of being near the jet thrust nozzles.
  Exhaust gases coming from underneath the swim platform contain carbon mon- oxide, a colorless, odorless gas which may cause brain damage or death when inhaled. Symptoms include nausea, diz-
ziness, and drowsiness.
(1) Be sure the engines are off, and then move to the stern of the boat.
(2) Pull out the ladder and climb up onto the swim platform. (See page 70 for informa- tion on ladder.)
Docking
(1) Make sure no obstructions, boats, or swimmers are close to the boat. Come to a stop before you reach the dock.
(2) Notice how wind and water currents are affecting boat movement as you attach your mooring lines and fenders.
(3) Approach the dock at idle speed. Use re- verse as necessary during slow-speed maneuvering to help control speed and direction. Position the boat according to wind and water conditions. WARNING! Do not use your hand, arm, or other parts of your body to try to keep the boat from hitting the dock. You could be injured if the boat pushes against the dock.
Wind or current pushing boat away from dock:
Slowly approach the dock at about a 45° an- gle. Secure the bow to the dock, and then use engine thrust or a boat hook to gently move the stern to the dock.
Operation
             Wind or current
                 (3) Return the ladder to the stowed position, and then sit in one of the seats provided.
Boarding from a dock or landing jetty
(1) Board the boat from the side. One per- son should board at a time by stepping into the boat. Never jump in. Avoid step- ping on slick gelcoat surfaces on the boat’s gunwales, especially if wet.
(2) Sit in one of the seats provided and put both feet on the deck.
 102
]]></page><page Index="110" isMAC="true"><![CDATA[Operation
Wind or current pushing boat toward dock:
Slowly maneuver to a shallow angle and al- low the boat to move toward the dock.
(3) (4)
(3 ft) deep from the bottom of the boat. Remember: turning is impossible with the engines stopped.
Get out of the boat and pull the bow up on the beach.
When leaving the beach, push the boat out into water that is at least 90 cm (3 ft) deep from the bottom of the boat before starting the engines.
    Wind or current
               No wind or current:
Approach the dock at a shallow angle. Se- cure the bow to the dock, and then use en- gine thrust or a boat hook to gently move the stern to the dock.
Beaching
NOTICE
  Small pebbles, sand, seaweed, and oth- er debris can be sucked into the jet in- takes and impair or damage the impellers. Always stop the engines be- fore beaching the boat. Be sure the boat is in water 90 cm (3 ft) deep from the bottom of the boat before starting the engines again.
  Do not beach the boat on rocky beach- es. The hull gelcoat and exposed pump housings can be damaged.
  Payattentiontoshiftsintides.Beaching at high tide may make it impossible to re-launch the boat if the tide recedes.
(1) Make sure no obstructions, boats, or swimmers are near the beach.
(2) Approach the beach slowly and stop the engines when the water is about 90 cm
Anchoring
WARNING
Always anchor from the bow. Anchoring from the stern will make the boat un- steady. A strong current can pull a stern- anchored boat underwater.
Select an anchor appropriate for your boat and water conditions. A “Danforth” (or fluke) type anchor is suitable for most applications; your Yamaha Boat Dealer can help you choose an anchor.
(1) Make sure the anchor line is securely tied to the anchor and to the bow eye or a bow cleat.
(2) Move the boat to the spot where you want to lower the anchor, heading the boat into the wind or current. Stop the boat, and then lower the anchor until it hits bottom.
(3) While keeping tension on the line, slowly back up the boat until you have let out line that is 4–6 times the depth of the wa- ter. For example, if you are anchoring in 10 feet of water, let out 40–60 feet of line. Secure the line.
(4) Pull on the line to be sure the anchor is holding. Also, periodically check your boat’s position against the shoreline to make sure it is not drifting and dragging the anchor. Reset if necessary.
    103
]]></page><page Index="111" isMAC="true"><![CDATA[ (5) To pull in (“weigh”) the anchor, start the engines and move forward, keeping ten- sion on the line as you pull it in. When the anchor line is straight up and down, pull hard to lift the anchor from the bottom material.
(6) If the anchor is stuck on the bottom, try this: Let out a few feet of anchor line and secure the line to the boat, again. Slowly maneuver the boat around the anchor until the anchor pulls loose. Keep the line taut during this procedure.
Crossing wakes and swells
You will not always have flat, smooth water. There will be swells and wakes from other boats, etc.
The best way to cross wakes and swells is with the least jolt to you and the boat. Small swells are not as difficult to cross as larger swells or wakes. Crossing a sharp wake gives more of a jolt than a broad swell.
To cross a wake or swell, change your speed and choose the angle at which you cross the wake or swell. Usually, a slower speed and “quartering” the wake (crossing at an angle) will reduce the jolt.
Two other things you may notice. The first is that crossing a group of wakes or swells is not as easy or smooth as crossing just one wake. The second is that when you quarter
Operation
the wake or swell, the boat will try to steer away from the wake or swell. When crossing at a 45° angle, you may not notice this, but at a smaller angle, say 10°, it can be very strong. Be prepared to steer and balance as neces- sary.
 Wake
90˚
45˚
10˚
  Sharp wakes
Broad swell
 104
]]></page><page Index="112" isMAC="true"><![CDATA[Operation
Post-operation checks
These post-operation procedures are devel- oped to help preserve the long-term appear- ance and reliability of your boat. Perform these procedures as soon as possible after the boat is loaded back on the trailer after the day’s use.
Some owners prefer to moor their boat sea- sonally, rather than keeping it on the trailer between uses. Extended mooring is not recommended by Yamaha, but can be performed if proper precautions are taken to help guard against prolonged environ- mental exposure and marine growth. Proper flushing of the cooling system is not possible with the boat in the water. In addi- tion, conditions such as stray electrical volt- age in the water, marine organisms, and saltwater corrosion can adversely affect the life of many boat components. NOTICE: Leaving the boat in the water for extended periods will accelerate the rate of normal deterioration of the exposed drive compo- nents.
If you do decide to moor your boat, be sure to remove it from the water periodically to clean the hull and jet pump area. The frequency of maintenance required will depend upon whether the water is salt water or fresh water and other local water conditions. See your dealer for additional preventative mainte- nance recommendations on mooring and/or saltwater use for your area.
(1) After putting the boat on the trailer, flush the cooling system to prevent the cooling system from clogging up with salt, sand, or dirt. (See page 111 for the cooling sys- tem flushing procedure.)
(2) Drain residual water from the exhaust system by starting the engine, and then alternately pushing the remote control le-
ver up to half throttle and back to idle for 10 to 15 seconds. NOTICE: Do not run the engine over 4000 r/min on land. Al- so, do not run the engine for more than 15 seconds without supplying water, otherwise, the engine could overheat and/or seize.
(3) Stop the engine.
(4) Wash down the hull, helm, and jet drive
unit with fresh water.
(5) Open the rear platform hatch. (See page
63 for rear platform hatch opening and
closing procedures.)
(6) Remove the access port cap to let any
water drain that has pooled on it. (See page 126 for access port cap removal and installation procedures.) If the boat will be stored on the trailer nearby, leave the cap out until you prepare to launch the boat again. If the boat will be trans- ported on the trailer any distance, tem- porarily reinstall the cap and close the hatch until you get home. Open the hatch again when you arrive and remove the cap as before. Leave the cap loose until you plan to transport the boat on the trailer again. NOTICE: Leaving the ac- cess port cap out when you are not using or transporting the boat helps keep it from becoming stuck in the ac- cess port.
(7) Remove the hull drain plug. (See page 81.)
(8) Rinse the engine compartment with a small amount of fresh water. Be careful not to get water on the air filter area or electrical components. Allow any water in the bilge to drain out. After the water has drained, wipe the engine compart- ment and bilge with dry rags.
 105
]]></page><page Index="113" isMAC="true"><![CDATA[(9) Reinstall the hull drain plug. NOTICE: Tighten the hull drain plug securely before launching the boat. Otherwise, water may flood the boat and cause it to submerge. Clean any foreign mate- rial, such as dirt or sand, from the threads and the O-ring on the hull drain plug before installing the drain plugs.
(10) Spray a rust inhibitor, such as Yamaha Silicone Protectant and Lubricant, on metallic parts to minimize corrosion.
(11) Use a boat cover designed for your boat, or store the boat in a building or under a canopy or carport in order to prevent rain from falling onto the boat. Because all of the water will not be drained from the deck automatically, take sufficient mea- sures to prevent rainwater from entering the boat. NOTICE: Make sure that the turnbuckles on the boat cover do not contact the boat directly when using the cover. Otherwise, the boat could be damaged.
(12) Turn the battery switch in the battery compartment to the OFF position. (See page 30 for more information.)
Operation
 106
]]></page><page Index="114" isMAC="true"><![CDATA[Trailering
Trailering the boat
WARNING
Avoid accident and injury from improper trailering:
  The trailer must be matched for the
boat’s weight and hull.
  The towing vehicle must have the ca-
pacity of pulling the load. Pulling a load that exceeds the towing capacity may cause loss of control.
  Be sure the boat is secured to the trailer and the trailer is properly hitched to the towing vehicle before towing.
  Read the manuals supplied with the trailer by the manufacturer.
A trailer is provided as standard equipment with your boat. If you need to obtain another trailer, choose one that is manufactured to carry a boat of the size and weight of your boat. Check the certification label on the left forward side of the trailer. This label is re- quired to show the Gross Vehicle Weight Rat- ing (GVWR), which is the load carrying capacity of the trailer plus the trailer’s weight. Be sure that the total weight of your boat, any cargo, and the trailer weight itself does not exceed the GVWR.
Hitch
The trailer hitch ball must match the size of the socket on the trailer hitch coupler. Hitch- es are divided into classes that specify the Gross Trailer Weight (GTW) and the maxi- mum tongue weight. Always use a hitch rated for the same or higher class. Use a bolted-on or welded-on hitch; clamp-on bumper hitch- es are not recommended. Be sure the trailer hitch’s release handle is latched with the lock pin installed before towing.
Use safety chains between the towing vehicle and the trailer so the trailer will not detach completely from the towing vehicle if it acci- dentally comes loose from the hitch ball. Crisscross the chains under the trailer tongue so the tongue will not hit the road surface if it falls loose. Rig the chains as tightly as possi- ble while allowing just enough slack to permit tight turns.
Be sure the tongue weight (vertical weight on the hitch point) is correct. Generally, 5% to 10% of the combined weight of the boat and trailer should be on the tongue. Too much or too little weight can cause difficult steering or trailer swaying.
Trailering checklist
  Check your state laws to be sure your trail- er meets all regulations, such as proper li- censing, brake, axle load, and safety chain requirements.
  Check the trailer for any loose fasteners or damaged parts.
  Check the tires for proper inflation.
  Check the wheel bearings and wheel lug
nuts before each trip.
  Check the tail, brake, and turn signal lights
for proper operation.
    107
]]></page><page Index="115" isMAC="true"><![CDATA[   Secure the bow of the boat to the trailer with the winch line and also with the chain. Secure the stern eyes to the trailer with tie- downs.
Trailering
  While traveling, check the wheel hubs on the trailer whenever you park. If a hub feels abnormally hot, have the bearing inspected before continuing your trip. On longer trips, it is a good idea to carry a set of spare wheel bearings, seals, and races.
  When making a turn, do not cut corners. The trailer has a smaller turning circle, so it turns more sharply around the corner than the towing vehicle.
Backing your trailer
It takes practice to back a trailer successfully. If you are not familiar backing up with a trailer, practice first in an open area away from ob- stacles.
 1
        1
Bow eye
             1
1
     1 TIP:
Keep the following points in mind when backing up
  Back slowly. Make steering adjustments in
small steps.
  Turn the towing vehicle’s wheels opposite
the direction you want the trailer to go.
  After the trailer begins moving, turn the
towing vehicle to follow it.
  Have a second person stand by to help di-
rect you with hand signals.
Launching
As a courtesy to other boaters, prepare your boat for launching before using the ramp.
Stern eye
During transport, use a boat cover to prevent any items from blowing out of the boat, or make sure to store any items inside the stor- age compartments and securely close the compartments.
  Be sure the access port cap is properly in- stalled (see page 126 for more information) and the rear platform hatch is closed se- curely.
  Be sure any cargo that must be carried in the boat as well as the all hatches are se- cured.
108
]]></page><page Index="116" isMAC="true"><![CDATA[Trailering
Each launch may have particular differences, Loading
 such as ramp angle, prevailing wind, waves, and water currents. If possible, watch a cou- ple of boaters launch their boats first to notice any problems. While every boater develops a preferred launch procedure, here is a recom- mended general procedure:
(1) Disconnect the trailer lights from the towing vehicle.
(2) Back the trailer down the ramp as close to 90° to the shoreline as you can. If pos- sible, have a second person act as an observer while standing to the side of the trailer. Stop when the tops of the trailer’s fenders are about 3 inches above the waterline.
(3) With the boat moving at the slowest idle speed, guide the boat onto the support rails. Use throttle only if necessary for steering ability. WARNING! Using too much throttle can cause the boat to jump over the front of the trailer, which can result in injury to the boat operator and bystanders.
(4) Make sure the boat is centered on the support rails and is headed straight for the bow stop (bumper board). Ease the boat forward until the bow rests against the bow stop. NOTICE: The winch line is not designed to pull the boat onto the trailer.
(5) Attach and tighten the winch line.
NOTICE: The winch line should not be the only line securing the bow during trailering. Use the chain along with the winch to secure the boat to the trailer.
       (1) Perform the pre-operation checks shown on page 85 that can be performed on land.
(2) Remove all trailering tie-down lines from the boat and attach your docking lines and fenders, if used.
(3) Disconnect the trailer lights from the towing vehicle.
(4) Back the trailer down the ramp as close to 90° to the shoreline as you can. If pos- sible, have a second person stand aside as an observer. Stop when the wheels are at least halfway submerged. Set the parking brake.
(5) Remove the bow line from the bow eye.
(6) Back the trailer farther into the water until just the tops of the fenders show, and then reset the parking brake. Board the boat and start it. If possible, remain on the trailer until the engines are warm and
are responding to throttle.
(7) Back the boat out into the water, watch-
ing carefully for people, other boats, or obstacles.
1 Bow eye
 1
        109
]]></page><page Index="117" isMAC="true"><![CDATA[ (6)
Pull the trailer up the ramp out of the way of other boaters. Attach the bow and stern tie-downs. Reconnect the trailer lights.
Trailering
  Remove all people and all cargo from the boat. Drain any excess water from the bilge using the bilge pump.
  Be sure all people are standing clear, and then lift the boat slowly and just far enough to verify that the boat is securely held and properly balanced. If necessary, lower the boat again and adjust the slings.
  When ready, lift the boat slowly and care- fully.
             1
1
1
Stern eye
(7) Perform the post-operation checks on page 105.
Lifting
NOTICE
Do not attach lifting cables to the bow eye, cleats, stern eyes, ski tow hook, or hand- grips. Serious damage to the boat can oc- cur. Use only a sling designed specifically for lifting boats.
If you need to remove the boat from the water without a trailer, use these guidelines:
  Use a sling-type lifting mechanism de-
signed for lifting boats. The sling should be covered with a protective material to pre- vent damage to the hull gelcoat.
  Use spreader bars to avoid side stress to the hull that may cause cracks in the gel- coat and fiberglass.
  Attach guidelines to the bow eye and stern eyes to control movement of the boat dur- ing lifting.
   110
]]></page><page Index="118" isMAC="true"><![CDATA[Care and storage
Post-operation care Flushing the cooling system
Cooling system flushing is essential to pre- vent the cooling system from clogging up with salt, sand, or dirt.
(1) Connect the garden hose adapter to a
garden hose.
(4) Make sure that the area around the boat is clear, and then start the engine. Imme- diately after the engine starts, fully turn the water supply on so that water flows out continually from the jet thrust nozzle and cooling water pilot outlet. NOTICE: Never turn on the water before start- ing the engine. The water could flow back through the muffler into the crankcase causing severe engine damage. Be sure to turn on the water immediately after starting the engine to prevent engine overheating.
(5) Runtheengineatafastidlefor3to5 minutes. If the engine stops while flush- ing, turn the water supply off immediately and perform the procedure again from step 4.
(6) Turn off the water supply, and then drain residual water from the exhaust system by alternately pushing the remote control lever up to half throttle and back to idle for 10 to 15 seconds.
(7) Stop the engine. NOTICE: Never have the water on when the engine is not running. The water could flow back through the muffler into the crankcase causing severe engine damage. Do not run the engine for more than 15 seconds after the water supply has been turned off to avoid engine over- heating.
(8) Remove the garden hose adapter.
(9) Install and tighten the cap securely.
  12
   1 Garden hose adapter
2 Garden hose
(2) Loosen the flush hose connector cap and remove it. Insert the garden hose adapter into the flush hose connector by pushing and twisting it until it is securely connected.
       1
3 2
   1 Flush hose connector
2 Flush hose connector cap
3 Garden hose adapter
(3)
Connect the garden hose to a water tap.
111
]]></page><page Index="119" isMAC="true"><![CDATA[ Cleaning the boat
WARNING
Gasoline and its vapors are highly flamma- ble and explosive. If there is fuel or a fu- el/water mixture in the engine compartment or the fuel tank compart- ment, wipe it up immediately with dry rags. Do not operate the boat until the source of the fuel leak is found and corrected.
TIP:
Quality Yamaclean®, YamashieldTM, and oth- er Yamalube care products are available from your Yamaha Boat Dealer.
(1) Remove the hull drain plug. (See page 82
for hull drain plug removal and installa- tion procedures.)
(4)
(5)
Care and storage
ture with clean, dry rags. NOTICE: Be careful not to get water on the air filter area or electrical components. Do not use high-pressure water when rinsing the engine or engine compartment as severe engine damage could result. Open the rear platform hatch. (See page 63 for rear platform hatch opening and closing procedures.)
Remove the access port cap to let any water drain that has pooled on it. (See page 126 for access port cap removal and installation procedures.) If the boat will be stored on the trailer nearby, leave the cap out until you prepare to launch the boat again. If the boat will be trans- ported on the trailer any distance, tem- porarily reinstall the cap and close the hatch until you get home. Open the hatch again when you arrive and remove the cap as before. Leave the cap loose until you plan to transport the boat on the trailer again. NOTICE: Leaving the ac- cess port cap out when you are not using or transporting the boat helps keep it from becoming stuck in the ac- cess port. (See page 126 for more in- formation.)
Securely install the hull drain plug by tightening it until it stop. NOTICE: Be- fore installing the hull drain plug, clean the drain plug thread and O-ring to re- move any foreign materials, such as dirt or sand. Otherwise, the hull drain plug could be damaged, allowing wa- ter to enter the hull. Check the O-ring on the hull drain plug and make sure that the hull drain plug is tightened se- curely before launching the boat. Oth- erwise, water may flood the boat and cause it to submerge.
                    1
1 Hull drain plug
(2) Clean the hull, boat interior, and drive unit with Yamaclean Wash & Wax Con- centrate, or a mild natural soap, and wa- ter. Rinse with fresh water. Scum on the hull can be removed with Yamaclean Hull CleanerTM. NOTICE: Incorrect cleaning can damage vinyl. See “Basic stain guide” on page 114.
(3) Clean the engine and bilge areas with Yamaclean Bilge CleanerTM or an equiv- alent and rinse with fresh water. Drain all water and wipe up any remaining mois-
(6)
112
]]></page><page Index="120" isMAC="true"><![CDATA[Care and storage
(7) Spray the exterior of the engine with Yamalube Silicone Protectant and Lubri- cant, or an equivalent. For areas requir- ing heavy protection, use YamashieldTM.
(8) Wax the hull with Yamaclean Spray Wax® or other non-abrasive wax de- signed for marine gelcoat. WARNING! Slippery surfaces can cause falls and injury. Be careful not to apply too much wax on deck and gunwale step- ping surfaces. This will make them slippery.
(9) Wipe all vinyl and rubber components, such as the seats and engine compart- ment seals, with Yamaclean Vinyl Dress- ingTM or other quality vinyl protectant. NOTICE: Some well-known “protec- tant” products on the market can ac- tually damage vinyl over time. Consult a Yamaha Boat Dealer if you want to use a product other than Yamaclean Vinyl Protectant.
(10) Wash the fabric of the bimini top with a mild natural soap in lukewarm water, then rinse. Do not use detergents. Allow to air dry thoroughly before storage.
 113
]]></page><page Index="121" isMAC="true"><![CDATA[Basic stain guide
Here are basic steps to remove common stains from boat upholstery. Consult a Yamaha Boat Dealer or upholstery-cleaning professional for difficult stains.
Care and storage
   TYPE OF STAIN
STEPS
(rinse with clean, warm water and then dry after application)
 1
2
3
General care/Dirt
A
B
—
Chewing gum
E
A
—
Coffee/Tea/Chocolate
B
—
—
Grease
E
B
—
Ink*
C
F
D
Ketchup
A
B
—
Lipstick
C
B
A
Mustard
A
B
C
Mildew/Wet leaves*
C
B
A
Motor oil
B
—
—
Permanent marker*
C
F
D
Suntan lotion*
A
B
—
Tar/Asphalt
E
B
—
                  * May cause permanent staining.
 A
Medium-soft brush with warm, soapy water
B
Yamaclean All Purpose Cleaner or equivalent
C
Isopropyl alcohol (91% is best)
D
Mixture of 1 tablespoon (15 ml) ammonia, 1/4 cup (60 ml) hydrogen peroxide, and 3/4 cup (177 ml) water
E
Wipe or scrape off excess (chill gum with ice first)
F
Name brand ink remover
         114
]]></page><page Index="122" isMAC="true"><![CDATA[Care and storage
Battery care
If the boat will not be used for more than a month, remove the battery and store it in a cool, dark place.
The battery is located in the battery compart- ment.
To remove the battery:
(1) Turn the battery switch to the OFF posi-
tion. (See page 30.)
(2) Disconnect the ground lead (black) and
the negative (–) battery lead (black).
(3) Disconnect the positive (+) battery lead
(red).
(4) Unfasten the battery strap, and then re-
move the battery from the boat.
ter) at least once a month and recharge
the battery if it gets too low.
To charge the battery:
(1) Remove the caps from the cells. Add dis-
tilled water if necessary to top up the
electrolyte to the proper level.
(2) Follow the battery manufacturer’s in- structions for charging. WARNING! When charging a battery, keep it well away from sparks and open flames, as it gives off explosive gases. When us- ing a battery charger, connect the bat- tery to the charger before you turn on the charger. This will prevent sparking at the terminals that could ignite bat-
tery gases.
To install the battery:
(1) Place the battery in the battery holder,
and then fasten the battery using the bat-
tery strap.
(2) Connect the positive (+) battery lead (red)
to the positive (+) battery terminal.
NOTICE: Reversal of the battery leads
will damage the electrical parts.
(3) Connect the negative (–) battery lead (black) and the ground lead (black) to the negative (–) battery terminal.
(4) Make sure that the battery is securely held in place.
      2
3
1
         4
2
          1 Positive (+) battery lead (red)
2 Battery strap
3 Negative (–) battery lead (black)
4 Ground lead (black)
To store the battery:
 (1)
(2)
(3)
Clean the battery casing and terminals using a mixture of baking soda and water (one tablespoon of baking soda to one cup of water).
Apply dielectric grease or petroleum jelly to the battery terminals and to all ex- posed connectors.
If the battery will be stored for a longer period, check its state of charge (use a hydrometer or a voltmeter and load tes-
115
]]></page><page Index="123" isMAC="true"><![CDATA[Care and storage
 Long-term storage
Storing your boat for prolonged periods of time, such as winter storage in freezing tem- perature, requires preventative maintenance to ensure against deterioration. It is advisable to have the boat serviced by an authorized Yamaha Boat Dealer before storage. Howev- er, the following procedures can be per- formed by the owner with a minimum of tools.
Fuel system
Fill the fuel tank with fresh fuel, adding one ounce of Fuel Med RX, available from your Yamaha Boat Dealer, to each gallon of fuel or use an equivalent according to the manufac- turer’s instructions. (See page 78 for informa- tion on filling the fuel tank.) Do not “top off” the tank, because fuel could spill. A full fuel tank is less likely to allow condensation to collect in the tank, reducing the chance of contaminated fuel. Running the engine with treated fuel during cooling system flushing will also help protect the fuel system.
TIP:
Use of Fuel Med RX eliminates the need to drain the fuel system. Consult a Yamaha Boat Dealer or other qualified mechanic if the fuel system is to be drained instead.
Lubrication
It is advisable to take the boat to a Yamaha Boat Dealer to have the engine fogged for long-term storage.
Grease points
To keep moving parts sliding or rotating smoothly, coat them with water-resistant grease.
  Throttle cable
Grease the throttle-cable inner wires at the pulley wheel of the APS.
   Recommended water-resistant grease: YAMALUBE MARINE GREASE or Yamaha Grease A
     Steering cable ball joints and inner wire Grease the steering cable and shift cable ball joints at the jet thrust nozzles. Extend the steering cable and shift cable inner wires and apply a thin coat of grease to them.
   116
]]></page><page Index="124" isMAC="true"><![CDATA[Care and storage
  Pivot points
Grease all pivot points of the steering and shift mechanism at the pump end.
  1
              Bearing housings
Grease the bearing housing through the grease nipples. NOTICE: Fill the grease slowly and carefully, because it can dam- age the hoses and the joints.
The first service should be done after 10 hours or 1 month by a Yamaha Boat Dealer. Fill the bearing housings with water-resistant grease through the grease nipples.
Grease capacity:
33.0–35.0 cc (1.11–1.18 oz)
After first service: Every 100 hours or 6 months (you may do this yourself).
Grease capacity:
6.0–8.0 cc (0.20–0.27 oz)
1 Bearing housing grease nipple
    117
]]></page><page Index="125" isMAC="true"><![CDATA[Maintenance
 Maintenance
WARNING
Be sure to turn off the engines when you perform maintenance unless otherwise specified. If you are not familiar with ma- chine servicing, this work should be done by a Yamaha Boat Dealer or other quali- fied mechanic.
Maintenance, replacement, or repair of the emission control devices and system may be performed by any marine SI engine repair es- tablishment or individual. Warranty repair, however, must be performed at an autho- rized Yamaha Boat Dealer. A service manual is available for purchase through a Yamaha Boat Dealer for owners who have the me- chanical skills, tools, and other equipment necessary to perform maintenance not cov- ered by this owner’s/operator’s manual.
Owner’s/operator’s manual
It is advisable to always carry the own- er’s/operator’s manual with you whenever you use the boat.
To protect these materials from water dam- age, it would be a good idea to put them in a waterproof bag. If your owner’s/operator’s manual is damaged, order a replacement from a Yamaha Boat Dealer.
The service information included in this man- ual is intended to provide you, the owner, with the necessary information for complet- ing your own preventive maintenance and minor repairs.
   118
]]></page><page Index="126" isMAC="true"><![CDATA[Maintenance
Periodic maintenance chart
The periodic maintenance chart gives general guidelines for periodic maintenance. Have a Yamaha dealer perform the checks in the following chart. However, maintenance may need to be performed more frequently depending on your operating conditions. If you have any questions, consult a Yamaha dealer.
This “ √ ” mark indicates items to be checked and serviced by a Yamaha dealer.
     Item
Operation
Initial
Thereafter every
10 hours
50 hours or 12 months *1
100 hours or 12 months *1
200 hours or 24 months *1
Fuel hoses, clamps, canister, and check valve
Check for damage, and check con- nections and tightening of clamps
√
Fuel filler cap
Check cap for damage, and check seal for cracks and deformation
√
Fuel tank
Check installation
√
√
Main switch and en- gine shut-off switch
Check operation
√
√
Batteries
Check state of charge and termi- nals, and check for broken battery straps
√
Battery leads
Check terminals
√
Battery switches
Check operation
√
√
Meters (after com- pleting the pre-oper- ation checks)
Check lighting
√
√
Neutral switches
Check operation
√
√
Hatch interlock switches (wet stor- age compartment)
Check operation
√
√
Blower
Check operation
√
√
Horn
Check operation
√
√
Navigation lights
Check lighting
√
√
Electric bilge pump
Check for water discharge, clean fil- ter, check hoses for damage, and check tightening of clamps
√
Other electrical com- ponents
Check operation of livewell, jet wash, stereo, and other compo- nents
√
√
Steering master ASSY
Check operation and tilting mecha- nism, and check for looseness
√
√
Steering cables
Check connections and exterior, and lubricate
√
                       119
]]></page><page Index="127" isMAC="true"><![CDATA[Maintenance
     Item
Operation
Initial
Thereafter every
10 hours
50 hours or 12 months *1
100 hours or 12 months *1
200 hours or 24 months *1
Articulating keel
Check operation, and check link rod for bends and damage
√
Remote control le- vers
Check exterior and operation, check shift operation, and check for looseness
√
√
Throttle cables
Check connections and exterior, and lubricate
√
Shift cables
Check connections and exterior, and lubricate (shift gate end)
√
Exhaust hoses, wa- ter locks, and resona- tors
Check for exhaust leakage, and check clamps at connections
√
Drain passages
Remove clogs
√
Drain plugs
Check O-rings
√
√
Hull and deck
Check for damage
√
√
Windshield and seats
Check installation and operation, and check for damage
√
√
T-top (210FSH SPORT) and bimini top
Check installation, and check for damage
√
√
Hatches, hinges, and packing seals
Check installation
√
√
Ladder
Check installation
√
√
Access port caps
Check exterior and installation
√
Spark plugs
Check
√
√
High-pressure fuel hoses
Check connections and exterior, and check for leakage
√
Engine oil
Replace
√
√
√
Engine oil filters
Replace
√
Air filter elements
Check for damage and dirt
√
Intake hoses and breather hoses
Check for damage, and check con- nections
√
Throttle bodies
Lubricate throttle valves
√
Anodes (engines)
Check for corrosion
√ *2
Valve clearance
Check and adjust
√ *2
Rubber couplings
Check for looseness and noise
√
Engine mounts
Check for damage and peeling
√
Cooling water hoses and cooling water pi- lot outlet hoses
Check for damage, and check con- nections
√
                               120
]]></page><page Index="128" isMAC="true"><![CDATA[Maintenance
     Item
Operation
Initial
Thereafter every
10 hours
50 hours or 12 months *1
100 hours or 12 months *1
200 hours or 24 months *1
Water inlet strainers
Check for damage
√
√
Intake grates
Check for damage
√
√
Impellers
Check for bends, damage, and for- eign material
√
√
Impeller ducts
Check and lubricate
√
Jet thrust nozzles
Check movement, and lubricate
√
Intermediate hous- ings
Lubricate
√
Anodes (jet pump units)
Check for corrosion
√
             *1: Whichever comes first.
*2: Check every 200 hours.
Perform the pre-operation checks and post-operation checks before performing periodic maintenance.
121
]]></page><page Index="129" isMAC="true"><![CDATA[Specifications
Specifications
  ITEM Specification
  Boat capacity
 Maximum people on board 10 person
 Maximum load capacity 1021 kg (2250 lb)
  Dimensions and weight
 Length
6480 mm (255.1 in)
Beam
2600 mm (102.4 in)
Height
210FSH SPORT 2860 mm (112.6 in)
210FSH DELUXE 2160 mm (85.0 in)
Draft
210FSH SPORT 460 mm (18.1 in)
210FSH DELUXE 430 mm (16.9 in)
Dry weight
210FSH SPORT 1362 kg (3003 lb)
210FSH DELUXE 1323 kg (2917 lb)
  Performance
 Maximum fuel consumption (for each engine)
33.0 L/h (8.7 US gal/h, 7.3 Imp.gal/h)
Cruising range at full throttle
2.98 hour
Trolling speed
1500 ±100 r/min
  Engine
 Number of engines
2
Engine type
Liquid cooled 4-stroke, DOHC
Number of cylinders
3
Engine displacement
1049 cm3
Bore × stroke
82.0 × 66.2 mm (3.23 × 2.61 in)
Compression ratio
11.0 : 1
Valve clearance-intake (cold)
0.15–0.22 mm (0.0059–0.0087 in)
Valve clearance-exhaust (cold)
0.26–0.32 mm (0.0102–0.0126 in)
Lubrication system
Dry sump
Cooling system
Water
Starting system
Electric
Ignition system
T.C.I.
Spark plug (NGK)
CR9EB
Spark plug gap
0.7–0.8 mm (0.028–0.031 in)
Battery capacity
12 V, 85 Ah
Charging system
Flywheel magneto
                              122
]]></page><page Index="130" isMAC="true"><![CDATA[Specifications
  Propulsion system
Jet pump type
Impeller rotation
Pitch angle
Transmission
Jet thrust nozzle angle
Fuel tank total capacity
Recommended engine oil
Recommended engine oil type SAE
Recommended engine oil grade API
Engine oil total quantity
ITEM Specification
  Drive unit
 Engine oil quantity without oil filter replacement
Engine oil quantity with oil filter replacement
Jet pump
Axial flow, single stage
Counterclockwise
11.2°
Direct drive from engine
23.0+23.0°
  Fuel and oil
 Recommended fuel
Minimum octane rating (PON)
Minimum octane rating (RON)
Regular unleaded gasoline
86
90
197 L (52.0 US gal, 43.3 Imp.gal)
 SAE 10W-30, 10W-40, 20W-40, 20W-50
API SG, SH, SJ, SL
3.7 L (3.91 US qt, 3.26 Imp.qt)
3.2 L (3.38 US qt, 2.82 Imp.qt)
3.4 L (3.59 US qt, 2.99 Imp.qt)
  Fuse amperage
 Electronic throttle valve fuse
Fuel pump fuse
Main relay drive fuse
Main fuse
Battery fuse
Accessory fuse
Bilge pump fuse
10 A
10 A
10 A
20 A
30 A
20 A
3A
             YAMALUBE 4W or 4-stroke motor oil
             123
]]></page><page Index="131" isMAC="true"><![CDATA[Trouble recovery
 Troubleshooting
If you have any trouble with your boat, use this section to check for the possible cause. If you cannot find the cause or if the procedure for replacement or repair is not described in this own- er’s/operator’s manual, ask your Yamaha Boat Dealer or a qualified mechanic for the proper service.
Troubleshooting chart
The Troubleshooting chart contains: “TROUBLE,” “POSSIBLE CAUSE,” “REMEDY,” and “PAGE.”
Check the possible cause and remedy, and also the referred page for the maintenance steps to solve the trouble.
  TROUBLE POSSIBLE CAUSE REMEDY PAGE
Starter mo- tor does not turn over
Fuse
Burned out
Replace fuse and check wiring
128
Battery
Run down
Recharge
115
Poor terminal con- nections
Tighten as required
115
Battery switch off
Turn on switch
30
Rear platform hatch
Not latched
Latch securely
63
Starter compo- nent
Faulty
Have serviced by Yamaha Boat Dealer
—
Remote control lever
Not in neutral posi- tion
Move remote control lever to neutral position
32
Starter mo- tor turns over/engine does not start
Engine shut-off switch
Clip on cord is not in place
Install clip in engine shut-off switch
30
Fuel
Empty
Refill as soon as possible
78
Stale or contaminat- ed
Have serviced by Yamaha Boat Dealer
—
Fuel tank
Water or dust col- lected
Have serviced by Yamaha Boat Dealer
—
Spark plug
Fouled or defective
Have serviced by Yamaha Boat Dealer
—
Crankcase
Filled with fuel
Have serviced by Yamaha Boat Dealer
—
Filled with water
Have serviced by Yamaha Boat Dealer
—
Fuel filter
Clogged or water collected
Have serviced by Yamaha Boat Dealer
—
                     124
]]></page><page Index="132" isMAC="true"><![CDATA[Trouble recovery
   TROUBLE POSSIBLE CAUSE REMEDY PAGE
Warning is displayed
Over temperature warning*
Jet intake clogged
Clean
126
Cooling system clogged
Clean
94
Low oil pressure warning*
Oil pressure dropped
Have serviced by Yamaha Boat Dealer
—
Fuel
Empty
Refill as soon as possible
78
Check engine warning
Faulty sensors
Have serviced by Yamaha Boat Dealer
—
Engine runs irregularly or stalls
Fuel
Empty
Refill as soon as possible
78
Stale or contaminat- ed
Have serviced by Yamaha Boat Dealer
—
Fuel filter
Water or dust col- lected
Have serviced by Yamaha Boat Dealer
—
Fuel tank
Water or dirt present
Have serviced by Yamaha Boat Dealer
—
Spark plug
Fouled or defective
Have serviced by Yamaha Boat Dealer
—
Incorrect heat range
Have serviced by Yamaha Boat Dealer
—
Gap incorrect
Have serviced by Yamaha Boat Dealer
—
Boat speed too slow or loses power
Cavitation
Jet intake clogged
Clean
126
Engine overheat*
Jet intake clogged
Clean
126
Cooling system clogged
Clean
94
Fuel filter
Clogged
Have serviced by Yamaha Boat Dealer
—
Spark plug
Fouled or defective
Have serviced by Yamaha Boat Dealer
—
Incorrect heat range
Have serviced by Yamaha Boat Dealer
—
Gap incorrect
Have serviced by Yamaha Boat Dealer
—
Fuel
Stale or contaminat- ed
Have serviced by Yamaha Boat Dealer
—
                          *Engine speed will be limited to 3500 rpm.
125
]]></page><page Index="133" isMAC="true"><![CDATA[Trouble recovery
 Emergency procedures Jet pump clean-out procedure
WARNING
Severe injury or death may result if you ig- nore any of the following:
  Turn off and remove both main switch
keys, remove the clip from the engine shut-off switch, and wait for all move- ment to stop before removing the ac- cess port caps.
  Never override the interlocks to run the engines with the rear platform hatch open.
  The impellers have sharp edges. Be careful when reaching into jet pump ar- eas.
If weeds or debris get caught in the intakes or impellers, cavitation can occur, and though the engine speed rises, forward thrust will de- crease. If this condition is allowed to contin- ue, jet pump damage can occur and the engines may overheat and seize. If there is any sign that a jet intake or impeller is clogged with weeds or debris, follow this clean-out procedure.
(1) Turn off and remove the main switch key, remove the clip from the engine shut-off switch, and wait for all movement to stop.
(2) Open the rear platform hatch. (See page 63.)
(3) Check that the retaining cord is securely attached to the access port cap and strap eye.
1 2
(4)
Retaining cord Strap eye
While holding the handle and pushing down, turn the access port cap counter- clockwise until the “SET” mark is aligned with the slot, and then lift the cap by the handle.
       2112
      NOTICE
  Do not lift or pull the cap with the retain- ing cord.
  Set the cap where it cannot be acciden- tally knocked overboard.
      1
2
1
2 Slot
“SET” mark
126
]]></page><page Index="134" isMAC="true"><![CDATA[Trouble recovery
   1
 3
1
2
1 Access port cap
1 “SET” mark
2 Slot
3 Edge of the access port
(8) Check that the cap is perpendicular to the centerline of the boat. Pull the handle forcefully to make sure that the cap is locked securely. If a strong pull will move the access port cap, it is not locked se- curely—the cap could be forced out by water pressure during operation.
(5)
(6)
Remove any weeds or debris from the drive shaft, impeller, pump housing, and jet thrust nozzle. If you cannot remove the debris, consult a Yamaha Boat Deal- er.
To reinstall the access port cap, first clean off any sand or other foreign matter from the cap or port surfaces. Apply a light coat of Yamalube Waterproof Ma- rine Grease (P/N: ACC-GREAS-10-CT), if available, to the seal of the access port cap. If grease is not available, apply the grease during the post-operation checks.
Insert the cap so that the “SET” mark is aligned with the slot, and then while pushing the handle turn the cap clock- wise until the “SET” mark is aligned with the edge of the access port.
  1
(7)
1 Perpendicular to the centerline of the boat
(9) Close the rear platform hatch.
NOTICE
Be sure the access port caps are locked securely in place. Otherwise, the caps could be forced out of the access ports by water pressure, causing loss of perfor- mance and possible damage.
   127
]]></page><page Index="135" isMAC="true"><![CDATA[TIP:
The rear platform hatch has interlocks to shut off the engines should the hatch be acciden- tally opened during operation. The engines will not restart unless the hatch is closed and latched.
Jump-starting
WARNING
Severe injury or death may result if you ig- nore any of the following:
  If the blower will not operate, ventilate
the engine compartment by opening the engine hood for several minutes before attempting a jump-start.
  Do not connect the negative (–) jumper cable to the negative (–) terminal of the dead battery. Sparks could ignite bat- tery or fuel vapors, which could cause an explosion.
If the boat battery runs down, the engine can be started in an emergency using a 12-volt booster battery and jumper cables.
To connect the jumper cables:
(1) Connect the positive (+) terminal of the dead battery to the positive (+) terminal of the booster battery with the positive (+) jumper cable.
(2) Connect one end of the negative (–) jumper cable to the negative (–) terminal of the booster battery.
(3) Connect the other end of the negative (–) jumper cable to an engine hanger. NOTICE: Be sure all connections are secure and correct before attempting to start the engine. Any wrong con- nection may damage the electrical system.
1 Negative (–) jumper cable 2 Positive (+) jumper cable 3 Engine hanger
4 Booster battery
(4) Start the engine, and then disconnect the jumper cables by reversing the above steps. NOTICE: Do not turn the main switch key for more than 5 seconds. If the engine does not start in 5 seconds, release the main switch key and try again after 15 seconds. Continuous cranking for more than 5 seconds will discharge the battery and the engine will not start. The starter motor may also be damaged if it is engaged con- tinuously for more than 5 seconds.
Fuse replacement
WARNING
Do not use fuses of a higher amperage than recommended. Substitution with a fuse that has an improper rating can cause extensive electrical system damage and possible fire.
If a fuse is blown, replace it with the proper fuse.
To replace a fuse:
(1) Open the engine hood. (See page 56.)
(2) Unfasten the band.
Trouble recovery
    1
2
       4
3
                 128
]]></page><page Index="136" isMAC="true"><![CDATA[Trouble recovery
     1
  123456
 87
1 Band
(3) Remove the fuse box from the air filter
case by pulling the fuse box toward the
bow.
(4) While pushing both sides of the fuse box
cover inward, pull the cover toward the bow and remove it.
1 Electronic throttle valve fuse 2 Fuel pump fuse
3 Main relay drive fuse
4 Main fuse
5 Fuse puller 6 Battery fuse 7 Spare fuse
8 Unused fuse
(5) When replacing the accessory fuse and bilge pump fuse, remove the fuse holder. (Open the battery compartment to ac- cess the accessory fuse and bilge pump fuse. [See page 66.])
           1
       23
1
                  1 Fuse box cover
129
1 Fuse holder
2 Accessary fuse 3 Bilge pump fuse
(6) Replace the blown fuse with the spare fuse of the correct amperage by using the fuse puller.
]]></page><page Index="137" isMAC="true"><![CDATA[    Fuse amperage:
Electronic throttle valve fuse:
10 A
Fuel pump fuse:
10 A
Main relay drive fuse:
10 A Main fuse: 20 A
Battery fuse: 30 A
Accessory fuse: 20 A
Bilge pump fuse: 3A
    (7) Install the fuse box cover.
(8) If the accessory fuse or bilge pump fuse
was replaced, install the fuse holder.
(9) Install the fuse box to the air filter case.
(10) Fasten the band.
(11) Close the engine hood.
Trouble recovery
Towing the boat
WARNING
  The operator of the towing boat must keep speed to a minimum and avoid traffic or obstacles which could be a hazard to either boat.
  The towing line should be long enough so the towed boat will not collide with the towing boat when slowing down.
The boat should be towed only if it becomes inoperative.
The towing rope should be long enough so that the boat will not collide with the towing boat when slowing down. A good rule of thumb is a tow rope which is three times the combined length of the towing boat and the boat.
Tow the boat using the bow eye only. Tow the boat at a no-wake speed. NOTICE: Do not tow the boat at speed fast enough to leave a wake (8 km/h, 5 mph). Severe engine damage could result because water can flood the non-operating engine through the water intake.
       1
  1 Bow eye
130
]]></page><page Index="138" isMAC="true"><![CDATA[Consumer information
Limited warranty
  131
]]></page><page Index="139" isMAC="true"><![CDATA[Consumer information
  132
]]></page><page Index="140" isMAC="true"><![CDATA[Consumer information
YAMAHA EXTENDED SERVICE (Y.E.S.)
   Keep your Yamaha Boat protected even after the 1-year warranty coverage provisions expire with genuine Yamaha Extended Service (Y.E.S.).
Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maxi- mum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.
• Y.E.S. is flexible. You choose the plan that’s right for you: 12 months, 24 months, 36 months, or up to 48 months on certain mod- els beyond the 1-year warranty coverage pe- riod. That means you can get up to 5 years of coverage on the power train, controls, and other components to match the comforting 5-year standard protection on the hull.
• Y.E.S. is designed and administered by the same Yamaha people who handle your war- ranty–and it shows in the comprehensive coverage benefits. There are no limitations on hours of use. Coverage isn’t limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufactur- ing defects just like the warranty. See the sample contract at your Yamaha dealer to see how comforting uninterrupted factory- backed protection can be.
• You don’t have to pay anything for cov- ered repairs. There’s no deductible to pay, and repairs aren’t “prorated.” You don’t have any “out-of-pocket” expenses for covered repairs.
• In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $250 reimbursement per occurrence for any rea-
sonable expenses you incur because your Yamaha needs covered service: replace- ment vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb cov- erage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.
• Y.E.S. coverage is honored at any autho- rized Yamaha dealer nationwide.
• Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make your Yamaha Boat much more valuable!
This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the first year of the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service. We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires. See your dealer today!
A special note:
If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number or Hull Identification Number. We’ll be happy to help you get the Y.E.S. coverage you need.
Yamaha Service Marketing P.O. Box 6555
Cypress, CA 90630 1-(866)-YES-EXTD (1-866-937-3983)
133
]]></page><page Index="141" isMAC="true"><![CDATA[Consumer information
Sample float plan
Leave a float plan with a responsible person on shore before boating. The example below can be copied and used.
  FLOAT PLAN
 VESSEL INFORMATION
BOAT MAKE: Yamaha MOTOR TYPE: Jet
 MODEL:
 LENGTH: REGISTRATION NO:
 DECK COLOR: HULL COLOR:
 PASSENGER
OPERATOR EMERGENCY PHONE: ADDRESS:
 PASSENGER #1: EMERGENCY PHONE: ADDRESS:
 PASSENGER #2: EMERGENCY PHONE: ADDRESS:
 PASSENGER #3: EMERGENCY PHONE: ADDRESS:
 PASSENGER #4: EMERGENCY PHONE: ADDRESS:
 DEPARTURE INFORMATION
POINT OF DEPARTURE: DATE/TIME:
 TOW VEHICLE LICENSE: TRAILER LICENSE: MAKE / MODEL
 DESTINATION INFORMATION
DESTINATION:
LORAN OR GPS COORDINATES:
INTENDED ACTIVITY:
EXPECTED RETURN
DATE:
TIME:
 LOCAL U.S. COAST GUARD PHONE #:
 NOTES: HULL COLOR:
 OPERATOR EMERGENCY PHONE: ADDRESS:
 PASSENGER #1: EMERGENCY PHONE: ADDRESS:
       134
]]></page><page Index="142" isMAC="true"><![CDATA[Index
A
Access port cap check ............................ 89 Accessory outlet ...................................... 54 Additional equipment
recommendations................................. 13 Anchor light (210FSH DELUXE) ............... 68 Anchor light (210FSH SPORT) ................. 67 Anchor storage compartment .................. 57 Anchoring............................................... 103 Approval label of emission control
E
Emergency procedures .......................... 126 Emission control information ..................... 2 Engine break-in ........................................ 84 Engine hood ............................................. 56 Engine oil.................................................. 79 Engine oil level check............................... 90 Engine oil requirement ............................. 79 Engine serial number ................................. 1 Engine shut-off cord (lanyard) check ....... 93 Engine shut-off switch ............................. 30 Engine shut-off switch check................... 94 Enjoy your boat responsibly..................... 21
F
Fire extinguisher check ............................ 88 Flushing the cooling system .................. 111 Fuel .......................................................... 78 Fuel level check........................................ 94 Fuel requirement ...................................... 78 Fuel system ............................................ 116 Fuel system checks ................................. 90 Fuse replacement .................................. 128
G
Getting to know your boat ....................... 96 Glossary, boat .......................................... 22 Glove compartment ................................. 62 Grease points.........................................116
H
Hazard information................................... 14 Hitch ....................................................... 107 Horn switch check ................................... 93 Hull Identification Number (HIN)................. 1
 certificate ................................................ 2
B
Backing your trailer ................................ 108 Basic stain guide.................................... 114 Battery care............................................ 115 Battery check ........................................... 91 Beaching ................................................ 103 Bilge water check..................................... 91 Bilge water, draining ................................ 81 Bilge water, draining on land ................... 81 Bilge water, draining on water ................. 82 Bimini top (210FSH DELUXE) .................. 75 Bimini top (210FSH SPORT) .................... 74 Bimini top, installing (210FSH DELUXE) .. 77 Bimini top, removing
(210FSH DELUXE) ................................ 77 Bimini top, setting up
(210FSH DELUXE) ................................ 75 Bimini top, storing in the fully collapsed
position (210FSH DELUXE) .................. 76 Bimini top, storing in the upright
position (210FSH DELUXE) .................. 76 Bimini top, trailering (210FSH DELUXE) .. 77 Blower switch check ................................ 92 Boarding from a dock or landing jetty ... 102 Boarding from the water ........................ 102 Boat characteristics ................................. 14 Boat control functions.............................. 30 Boating with passengers ....................... 101
C
Check engine warning ............................. 46 Cleaning the boat................................... 112 Communication error warning ................. 48 Cooling water pilot outlet check .............. 94
135
Courtesy light switch................................ 51 Crossing wakes and swells .................... 104 Cruise assist............................................. 48 Cruising limitations................................... 11
D
Docking .................................................. 102 Drain plug check ...................................... 91 Driving your boat......................................96
]]></page><page Index="143" isMAC="true"><![CDATA[ I
Identification number records .................... 1
J
Jet intake checks ..................................... 90 Jet pump clean-out procedure .............. 126 Jump-starting......................................... 128
Index
Post-launch checks ................................. 94 Post-operation care ............................... 111 Post-operation checks ........................... 105 Pre-launch checks ................................... 87 Pre-operation check points...................... 87 Pre-operation checklist ............................ 85 Primary Identification (PRI-ID) number....... 1
R
Remote control lever checks ................... 87 Remote control levers .............................. 32 Required equipment................................. 13 Reverse RPM control ............................... 49 Rules of the road......................................17
S
Sample float plan ................................... 134 Seats ........................................................ 55 Specifications......................................... 122 Starting the engine ................................... 96 Steering .................................................... 34 Steering system checks ........................... 87 Stereo system .......................................... 54 Stopping the boat .................................. 101 Stopping the engines ............................... 98 Storage compartments ............................ 57 Swim platform .......................................... 70 Switch circuit breakers............................. 53 Switches................................................... 50
T
Tachometers ............................................ 36 Tilt lever....................................................34 To get more boating safety information ... 21 Towing the boat ..................................... 130 Trailering checklist ................................. 107 Trailering the boat .................................. 107 Trip screen ............................................... 39 Troubleshooting ..................................... 124 Troubleshooting chart ............................ 124 T-top (210FSH SPORT)............................ 73 Turning the boat ....................................... 99
W
Wakeboarding and water-skiing .............. 16 Wet storage compartment ....................... 63 Windshield................................................ 67
L
Labels, important ....................................... 4 Labels, other .............................................. 9 Labels, warning .......................................... 6 Ladder ...................................................... 70 Launching .............................................. 108 Learning to operate your boat ................. 96 Leaving a dock......................................... 99 Lifting ..................................................... 110 Limitations on who may operate the
boat ...................................................... 10 Limited warranty .................................... 131 Loading .................................................. 109 Long-term storage ................................. 116 Low oil pressure warning ......................... 46 Lubrication ............................................. 116
M
Main components, location ..................... 23 Main switches .......................................... 31 Maintenance .......................................... 118 Manufactured date label ............................ 3 Multi-function display elements ............... 48 Multi-function display unit operation ....... 36
N
Navigation and anchor lights switch ........ 51 Navigation and anchor lights switch
check .................................................... 92 Night operation ........................................ 15 No-wake mode ........................................ 48 No-wake mode/cruise assist switch ........ 48
O
Operational requirements ........................ 12 Over temperature warning ....................... 47 Owner’s/operator’s manual ................... 118
P
Periodic maintenance chart ................... 119
136
]]></page><page Index="144" isMAC="true"><![CDATA[Index
Y
YAMAHA EXTENDED SERVICE
(Y.E.S.) ................................................ 133
 137
]]></page><page Index="145" isMAC="true"><![CDATA[ For your best ownership experience, think Genuine Yamaha!
Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for aftermarket parts that may not provide full confidence and satisfaction?
Genuine Yamaha Accessories – Yamaha only offers accessories that meet our high standards for quality and performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and perform right – right out of the box.
Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products. They’re formulated and approved by the toughest judges we know: the Yamaha engineering teams that know your Yamaha from the inside out.
Genuine Yamaha Service Manuals – Get the same factory manual for your vehicle that the technicians at your authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you can order them directly through yamahapubs.com.
Genuine Yamaha products are available only from your Yamaha dealer. Find out more at yamaha-motor.com
]]></page><page Index="146" isMAC="true"><![CDATA[ Printed in USA
July 2020–0.3 × 1 CR
]]></page></pages></Search>