﻿<?xml version="1.0" encoding="utf-8" standalone="no"?><Search><pages Count="142"><page Index="1" isMAC="true"><![CDATA[2018 Yamaha Boat 210 FSH Sport 210 FSH Deluxe 210 FSHOWNER’S/OPERATOR’S MANUALU.S.A. EditionLIT-18626-11-82 F4A-F8199-10Read this manual carefully before operating this boat.]]></page><page Index="2" isMAC="true"><![CDATA[WARNING: Operating, servicing and maintaining a recreational marine vessel can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, service your vessel in a well-ventilated area and wear gloves or wash your hands frequently when servicing this vessel.For more information go to www.P65warnings.ca.gov/marineRead this manual carefully before operating this boat. This manual should stay with the boat if it is sold.]]></page><page Index="3" isMAC="true"><![CDATA[Important manual informationTo the ownerThank you for choosing a Yamaha boat. This owner’s/operator’s manual contains informa- tion you will need for proper operation, main- tenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your new Yamaha. If you have any questions about the operation or maintenance of your boat, please consult a Yamaha Boat Dealer.In this manual, information of particular impor- tance is distinguished in the following ways:This is the safety alert symbol. It is used to alert you to potential personal injury haz- ards. Obey all safety messages that follow this symbol to avoid possible injury or death.A WARNING indicates a hazardous situa- tion which, if not avoided, could result in death or serious injury.NOTICEA NOTICE indicates special precautions that must be taken to avoid damage to the boat or other property.TIP:A TIP provides key information to make pro- cedures easier or clearer.Because Yamaha has a policy of continuing product improvement, this product may not be exactly as described in this owner’s/opera- tor’s manual. Specifications are subject to change without notice.This manual should be considered a perma- nent part of this boat and should remain with it even if the boat is subsequently sold.210 FSH Sport/210 FSH Deluxe/210 FSH OWNER’S/OPERATOR’S MANUAL ©2017 by Yamaha Motor Corporation, U.S.A.1st Edition, July 2017All rights reserved.Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A.is expressly prohibited.Printed in U.S.A.P/N LIT-18626-11-82WARNING]]></page><page Index="4" isMAC="true"><![CDATA[Table of contentsGeneral and important labels........... 1Identification number records...........1 Primary Identification (PRI-ID)number ....................................... 1 Hull Identification Number (HIN) ... 1 Engine serial number .................... 1Emission control information ............ 2Approval label of emission control certificate.................................... 2 Manufactured date label................3 Important labels................................4Warning labels .............................. 6 Other labels...................................9Safety information........................... 10Limitations on who may operatethe boat ....................................... 10 Cruising limitations ......................... 11 Operational requirements............... 12 Required equipment.......................13Additional equipment recommendations........................ 13Hazard information.........................14 Boat characteristics........................14 Night operation...............................15 Wakeboarding and water-skiing.....16 Rules of the road ............................ 17 To get more boating safetyinformation .................................. 21 Enjoy your boat responsibly ........... 21Description....................................... 22Boat glossary ................................. 22 Location of main components ........ 23 Exterior components ................... 23Stern components ....................... 26 Helm components ....................... 27 Engine components .................... 29Control function operation ............. 30Boat control functions..................... 30Engine shut-off switch ................. 30 Battery switches .......................... 30 Main switches.............................. 31Remote control levers ................. 32 Steering ...................................... 33 Tilt lever ...................................... 34Instrument operation........................ 35Tachometers............................... 35 Multi-function display unitoperation.................................. 35 Multi-function display elements... 35 Screen tabs (screen tab bar) ...... 36 Data bar ...................................... 36 Information display(home screen tab).................... 36 Cruising information display(trip screen tab)........................ 37 Multi-function display unitsettings (setting screen tab)..... 38 Setting the time ........................... 38 Selecting the display units .......... 39 Starboard/port engine wellnessdisplay...................................... 39 Setting the day mode and nightmode........................................ 39 Setting the display language....... 40 Setting the aeration time(aerator button) ........................ 40 Resetting the settings to thedefault settings......................... 41 No-wake mode/cruise assistswitch....................................... 41 Operating the boat with aminimal wake(no-wake mode)....................... 41 Operating the boat at a steadyspeed (cruise assist)................ 42 Operating the boat in reversewith more thrust(reverse RPM control).............. 43 Warnings..................................... 43 Warning definition table .............. 43 Check engine warning ................ 44 Low oil pressure warning ............ 44 Over temperature warning .......... 44 Generic warning.......................... 46Switches......................................... 47 Courtesy light switch ................... 48 Navigation and anchor lightsswitch....................................... 48 Aerator switch ............................. 49]]></page><page Index="5" isMAC="true"><![CDATA[Switch circuit breakers ................ 50 Accessory outlet ............................. 51 Stereo system ................................ 51Equipment operation ...................... 52Seats .............................................. 52Leaning post................................52Jump seats..................................52 Engine hood ................................... 53Storage compartments...................53 Anchor storage compartment......53 Bow storage compartment .......... 54 Insulated fish box ........................ 54 Stern storage compartment......... 55 Lockable storage compartment...55 Glove compartment.....................58 Storage pocket ............................ 59 Wet storage compartment...........59 Bucket storage compartment ...... 60 Rod holders.................................60 Livewell ....................................... 61 Battery compartment...................62Windshield...................................... 63 Anchor light (210 FSH Sport) ......... 64 Anchor light(210 FSH Deluxe/210 FSH) ........ 64 Swim platform and ladder .............. 66 Jet wash ......................................... 67 T-top (210 FSH Sport).................... 70 Bimini top (210 FSH Sport) ............ 70 Bimini top (210 FSH Deluxe).......... 71Setting up the bimini top.............. 71 Storing the bimini top in theupright position.........................72 Storing the bimini top in the fullycollapsed position..................... 73 Trailering with the bimini top .......73Operation and handling requirements.................................... 74Fuel requirement ............................ 74 Fuel ............................................. 74 Engine oil requirement ................... 75 Engine oil .................................... 75 Draining the bilge water ................. 77Table of contentsDraining the bilge water onland .......................................... 77Draining the bilge water onwater ........................................ 78First-time operation ........................ 80Engine break-in.............................. 80Pre-operation checks....................... 81Pre-operation checklist ............... 81 Pre-operation check points ............ 83Pre-launch checks ...................... 83 Steering system checks .............. 83 Remote control lever checks ...... 83 Fire extinguisher check ............... 84 Access port cap check ................ 85 Jet intake checks ........................ 86 Fuel system checks .................... 86 Engine oil level check ................. 86 Battery check .............................. 87 Bilge water check........................ 87 Drain plug check ......................... 87 Blower switch check ................... 88 Navigation and anchor lightsswitch check ............................ 88 Horn switch check....................... 89 Engine shut-off cord (lanyard)check ....................................... 89 Post-launch checks..................... 90 Engine shut-off switch check ...... 90 Cooling water pilot outletcheck ....................................... 90 Fuel level check .......................... 90Operation ......................................... 92Driving your boat............................ 92 Getting to know your boat........... 92 Learning to operate your boat..... 92 Starting the engine...................... 92 Stopping the engines .................. 94 Leaving a dock............................ 95 Turning the boat.......................... 95 Boating with passengers............. 97 Stopping the boat........................ 97 Boarding from the water ............. 98 Boarding from a dock or landingjetty .......................................... 98 Docking ....................................... 98]]></page><page Index="6" isMAC="true"><![CDATA[Table of contentsBeaching ..................................... 99 Anchoring .................................... 99 Crossing wakes and swells ....... 100Post-operation checks.................. 101Trailering ..........................................103Trailering the boat ........................ 103 Hitch .......................................... 103 Trailering checklist .................... 103 Backing your trailer ................... 104 Launching.................................. 104 Loading ..................................... 105 Lifting......................................... 106Care and storage .............................107Post-operation care......................107 Flushing the cooling system......107 Cleaning the boat ...................... 108 Basic stain guide ....................... 110 Battery care...............................111Long-term storage........................112Fuel system...............................112 Lubrication................................. 112 Grease points............................112Maintenance................................... 114Maintenance................................. 114Owner’s/operator’s manual andtool kit.....................................114 Periodic maintenance chart....... 115Specifications ................................ 118Specifications ............................... 118Trouble recovery ........................... 120Troubleshooting ........................... 120Troubleshooting chart ............... 120 Emergency procedures ................ 122Jet pump clean-outprocedure ............................... 122Jump-starting ............................ 124 Fuse replacement ..................... 124 Towing the boat......................... 126Consumer information................... 127Limited warranty........................... 127 YAMAHA EXTENDED SERVICE(Y.E.S.) ..................................... 130 Sample float plan ......................... 131Index............................................... 132]]></page><page Index="7" isMAC="true"><![CDATA[Identification number recordsRecord your Primary Identification (PRI-ID) number, Hull Identification Number (HIN), and engine serial number in the spaces provided to assist you in ordering spare parts from your Yamaha Boat Dealer. Also, record and keep these ID numbers in a separate place in case your boat is stolen.Primary Identification (PRI-ID) numberThe PRI-ID number is stamped on a label at- tached inside the engine compartment. (See page 53 for engine hood opening and closing procedures.)Hull Identification Number (HIN)The HIN is stamped into the right rear corner of the hull.General and important labels11 Hull Identification Number (HIN)Engine serial numberThe engine serial numbers are stamped on a label attached to the each engine unit. (See page 53 for engine hood opening and closing procedures.)11Primary Identification (PRI-ID) numberPRI-I.D.YAMAHA MOTOR CO.,LTD.ASSEMBLED IN U.S.A. FROM AMERICAN AND JAPANESE COMPONENTS.ASSEMBLÉ AUX ÉTATS-UNIS DE PIÈCES AMÉRICAINES ET JAPONAISES.MODEL1 Engine serial number11]]></page><page Index="8" isMAC="true"><![CDATA[General and important labelsEmission control informationThis engine family conforms to U.S. Environ- mental Protection Agency (EPA) regulations for marine SI engines applicable at the time of manufacture.This engine is certified to operate on regular unleaded gasoline.Approval label of emission control certificateThese labels are attached to each engine unit and to the inside of the engine compartment. (See page 53 for engine hood opening and closing procedures.)11 Emission control information labelEMISSION CONTROL INFORMATIONTHIS ENGINE CONFORMS TO  U.S. EPA EXHAUST REGULATIONS FOR SI MARINEENGINES. REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.ENGINE FAMILY : DISPLACEMENT :MAX POWER : kW FEL : HC+NOx  , CO  g/kW-hYAMAHA MOTOR CO.,LTD.liters121 Emission control information label]]></page><page Index="9" isMAC="true"><![CDATA[General and important labelsEMISSION CONTROL INFORMATIONTHIS ENGINE CONFORMS TO U.S. EPA EXHAUST REGULATIONS FOR SI MARINE ENGINES. REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. MEETS U.S. EPA EVAP STANDARDS USING CERTIFIED COMPONENTS ENGINE FAMILY: DISPLACEMENT: LITERS MAX POWER: kW FEL: HC+NOx ,CO g/kW-h EPA CERTIFIED EVAP COMPONENTS: JNCNPLINEME1. JATWPMDRN212YAMAHA MOTOR CO.,LTD.Manufactured date labelThis label is attached to each engine unit. (See page 53 for engine hood opening and closing procedures.)11 Manufactured date label3]]></page><page Index="10" isMAC="true"><![CDATA[General and important labelsImportant labelsRead the following labels before operating this boat. If you need any additional information, contact a Yamaha Boat Dealer.2 1141534567 916 8 74]]></page><page Index="11" isMAC="true"><![CDATA[General and important labels101210 1313 1110171813 105]]></page><page Index="12" isMAC="true"><![CDATA[General and important labels Warning labelsIf any of these labels is damaged or missing, contact a Yamaha Boat Dealer for a replacement.12634]]></page><page Index="13" isMAC="true"><![CDATA[567General and important labels7]]></page><page Index="14" isMAC="true"><![CDATA[General and important labels88910 1112]]></page><page Index="15" isMAC="true"><![CDATA[Other labels1314 1516 1718All applicable electrical system components installed as original equipment meet appropriate U.S.C.G. requirements for ignition protection. (Ref. 33 CFR 183.410 and 183.440)Y AMAHA 60E-83627-00General and important labelsMAXIMUM CAPACITIES10PERSONS OR 1860 LBS. 2250 POUNDS, PERSONS, GEARTHIS BOAT COMPLIES WITH U.S. COAST GUARD SAFETY STANDARDS IN EFFECT ON THE DATE OF CERTIFICATIONMEETS U.S. EPA EVAP STANDARDS USING CERTIFIED COMPONENTSMANUFACTURER: YAMAHA JET BOAT MANUFACTURING U.S.A., INC.MODEL: VONORE, TNDESIGN COMPLIANCE WITH NMMA REQUIREMENTS IS VERIFIED. MANUFACTURER RESPONSIBLE FOR PRODUCTION CONTROL.NATIONAL MARINE MANUFACTURERS ASSOCIATION9]]></page><page Index="16" isMAC="true"><![CDATA[Safety informationThe safe use and operation of this boat is dependent upon the use of proper operat- ing techniques, as well as upon the com- mon sense, good judgment, and expertise of the operator. Every operator should know the following requirements before operating the boat.● Before operating the boat, read the own- er’s/operator’s manual, the Operation In- struction card, and all labels on the boat. Also, watch the Basic Orientation Video provided with your boat. These materials should give you an understanding of the boat and its operation.● Neverallowanyonetooperatethisboatun- til they too have read this owner’s/opera- tor’s manual, the Operation Instruction card, and all labels, and, if possible, watched the Basic Orientation Video. Showing them the video may help reinforce the information contained in these materi- als.Limitations on who mayoperate the boat● Yamaharecommendsaminimumoperator age of 16 years old.Adults must supervise use by minors. Know the operator age and training require- ments for your state. A boating safety course is recommended and may be re- quired in your state. You can find local rules by contacting the United States Coast Guard (USCG), the National Association of State Boating Law Administrators, or your local Power Squadron.● Thisboatisdesignedtocarrytheoperator, up to 9 passengers, and cargo. Never ex- ceed the maximum load limit or allow more than 10 persons (or 9 persons if the wake- boarder or water-skier is being pulled) to ride in the boat at any time. Weight distribu- tion affects performance. Keep weight in the boat low and evenly distributed from side-to-side and bow-to-stern. Remove any unnecessary cargo and store it on shore.Maximum load:Total weight of cargo, operator, and passengers:1021 kg (2250 lb)Total weight of operator and passen- gers:844 kg (1860 lb)10]]></page><page Index="17" isMAC="true"><![CDATA[Cruising limitations● Scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.● Operate defensively at safe speeds and keep a safe distance from people, objects, and other watercraft.● Do not follow directly behind other water- craft.● Do not go near others to spray or splash them with water.● Avoid sharp turns or other maneuvers that make it hard for others to avoid you or un- derstand where you are going.● Avoid areas with submerged objects or shallow water.● Take early action to avoid collisions. Re- member, boats do not have brakes.● Do not pull the remote control lever back to idle when trying to steer away from ob- jects—you need throttle to steer. Always check throttle, shift, and steering controls for proper operation before starting boat.● Operate within your limits and avoid ag- gressive maneuvers to reduce the risk of loss of control, ejection, and collision.Safety information● Thisisahigh-performanceboat—notatoy. Sharp turns or jumping wakes or waves can increase the risk of back/spinal injury (pa- ralysis), facial injuries, and broken legs, an- kles, and other bones. Do not jump wakes or waves.● Donotoperatetheboatinroughwater,bad weather, or when visibility is poor; this may lead to an accident causing injury or death. Be alert to the possibility of adverse weath- er. Take note of weather forecasts and the prevailing weather conditions before setting out in your boat.● Never operate in water that is less than 90 cm (3 ft) deep from the bottom of the boat, otherwise you increase your chance of hitting a submerged object, which could result in injury.● Leave a “float plan” with a responsible per- son on shore. Tell where you plan to go and when you plan to arrive, and provide a de- scription of your boat. Advise this person if your plans change and also when you ar- rive to prevent false alarms. A sample float plan is included on page 131.● Follow navigation rules and state and local laws that apply to your boat.90 cm (3 ft)11]]></page><page Index="18" isMAC="true"><![CDATA[Safety informationOperational requirements● Theoperatorandallpassengersmustwear a U.S. Coast Guard (USCG) approved per- sonal flotation device (PFD).● Attachtheengineshut-offcord(lanyard)to the PFD and keep it free from the steering wheel or other controls so that the engine stops if the operator accidentally leaves the helm. Failure to attach the engine shut-off cord (lanyard) could result in a runaway boat if the operator is ejected.After operation, remove the engine shut-off cord (lanyard) and the main switch key to avoid accidental starting or unauthorized use by children or others.1121 PFD● Eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your boat. Re- straining straps for eyewear are made which are designed to float should your eyewear fall in the water.● Footwear is recommended.● Neveroperatetheboatafterconsumingal-cohol or taking drugs.● Forreasonsofsafetyandpropercareoftheboat, always perform the pre-operation checks listed on page 81 before operating the boat.● Passengersmustalwayssitinadesignated seating area, place feet on the deck, and hold on to the handgrips when the boat is in motion.● Alwaysconsultyourdoctoronwhetheritis safe for you to ride in this boat if you are pregnant or in poor health.● Donotattempttomodifythisboat. Modifications to your boat may reduce safe- ty and reliability, and render the boat unsafe or illegal to use.1 Engine shut-off switch2 Engine shut-off cord (lanyard)● Scan constantly for swimmers and stay away from swimming areas. Swimmers are hard to see and you could accidentally hit someone in the water.● Avoidbeinghitbyanotherboat.Youshould always take responsibility to watch for traf- fic; other boaters may not be watching for you. If they do not see you, or you maneu- ver more quickly than other boaters expect, you risk a collision.● Maintain a safe distance from other boats and watercraft, and also watch for ski ropes or fishing lines. Obey the “Rules of the road”, and be sure to check behind you be- fore making a turn. (See “Rules of the road” on page 17.)12]]></page><page Index="19" isMAC="true"><![CDATA[Required equipmentThe U.S. Coast Guard (USCG) has regula- tions which describe minimum standards of safety. You must comply with these regula- tions, which apply to boats like your boat which are less than 26 feet long.● Personalflotationdevices(PFD):Type I, II, or III as required for all people on board (see “Operational requirements” for more information), plus at least one Type IV (throwable type).● Fireextinguisher:At least one B-1 type hand-held portable fire extinguisher.● Visualdistresssignals:It is recommended that a USCG-approved pyrotechnic device be stored on your boat. A mirror can also be used as an emergency signal. Contact your Yamaha Boat Dealer or the Coast Guard for more information.● Soundsignallingdevice:Your boat is equipped with a horn that can be used to signal other boats. See “Rules of the road” for more information.● Navigationlights:Your boat is equipped with navigation lights for use between sunset and sunrise, and during periods of reduced visibility, such as fog. Be sure these lights are working and are turned on when necessary. (See pages 48 and 64 for more information.)Safety informationAdditional equipmentrecommendationsThe following equipment can help make your boating experience safer and more enjoyable:● Mooringfendersandlines.● Anchorwithsuitableline(a“Danforth”typeanchor and line that is at least 6 times the depth of the water where you will drop an- chor are recommended).● Manual-typebilgepump.● First-aidkit.● Waterproofflashlightwithextrabatteries.● Tool kit with assorted screwdrivers, pliers,wrenches (including metric sizes), andelectrical tape.● Oarorpaddle(lookforonewithaboathookon the other end).● Spareparts,suchasfuses.● Navigationchartsforthewaterswhereyouwill be boating.● Tow-rope.13]]></page><page Index="20" isMAC="true"><![CDATA[Safety informationHazard informationNever start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of con- sciousness and death within a short time. Al- ways operate the boat in an open area.It is also important to have the engine off when anyone is using the ladder on models equipped with one because of the carbon monoxide in the exhaust gases coming from underneath the step.Boat characteristics● Jet thrust turns the boat. Moving the remote control lever completely back to idle or the neutral position produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. You may still have some turning ability immediately after moving the remote control lever back to idle, but once the engine slows down, the boat will no longer respond to steering wheel input until you apply throttle again or you reach a trolling speed. Practice turning in an open area without obstructions until you have a good feel for the maneuver.● This Yamaha boat is water-jet propelled. The pump is directly connected to the en- gine. This means that the jet thrust will pro- duce some movement whenever the engine is running. The boat has a “neutral” position, but since the boat is always pro- ducing thrust while the engine is running, some forward or reverse movement may occur.● Do not use the reverse function to slow down or stop the boat above trolling speed as it could cause you to lose control, be ejected, or impact the steering wheel or oth- er parts of the boat. This could increase the risk of serious injury. It could also damage the shift mechanism.● Reversecanbeusedtoslowdownorstop during slow-speed maneuvering, such as when docking. Once the engine is idling, shift to reverse and gradually increase en- gine speed. Make sure that there are no ob- stacles or people behind you before shifting into reverse.14]]></page><page Index="21" isMAC="true"><![CDATA[●●Keepawayfromtheintakegrateswhilethe engines are on. Items such as long hair, loose clothing, or PFD straps can become entangled in moving parts, resulting in se- vere injury or drowning.Never insert any object into the jet thrust nozzles while the engines are running. Se- vere injury or death could result from com- ing in contact with the rotating parts of the jet pumps.Safety informationNight operationWhen using your boat before dawn or after dusk, you must have both bow and anchor lights operating. When at anchor in the dark, the anchor light must be lit. (See pages 48 and 64 for instructions.)210 FSH Deluxe/210 FSH21210 FSH Sport1 2●Intake grateJet thrust nozzleStop the engines and remove the clip from the engine shut-off switch before removing any debris or weeds, which may have col- lected around the jet intakes. (See page 122 for more information.)15]]></page><page Index="22" isMAC="true"><![CDATA[Safety informationWakeboarding and water-skiingYou can use the boat to tow a wakeboarder or water-skier, using the ski tow hook provided. It is the boat operator’s responsibility to be alert to the safety of the wakeboarder or wa- ter-skier and others. Know and follow all state and local regulations in effect for the waters in which you will be operating.The following are some important consider- ations for minimizing risks while pulling a wakeboarder or water-skier.● The wakeboarder or water-skier shouldwear an approved PFD, preferably a bright- ly colored one so boat operators can see the person being pulled.● The wakeboarder or water-skier should wear protective clothing. Severe internal in- juries can occur if water is forced into body cavities as a result of falling into the water or while reboarding. Normal swimwear does not adequately protect against forceful wa- ter entry into the rectum or vagina. The per- son being pulled should wear a wetsuit bottom or clothing that provides equivalent protection. Such clothing includes thick, tightly woven, sturdy, and snug-fitting ap- parel such as denim, but does not include spandex or similar fabrics, like those used in bicycle shorts.● A second person should be on board as a spotter to watch the wakeboarder or water- skier; in most states, it is required by law. Let the person being pulled direct the oper- ator’s control of speed and direction with hand signals. Be sure the seat is locked in place (see page 52) before getting under- way.● Whenpreparingtopullthewakeboarderor water-skier, operate the boat at the slowest possible speed until the boat is well away from the person being pulled and slack in the tow-rope is taken up. Make sure that the rope is not looped around anything.After checking that the wakeboarder or wa- ter-skier is ready and that there is no traffic or other obstacles, apply enough throttle to raise the person.● Makesmooth,wideturns.Theboatiscapa- ble of very sharp turns, which could exceed the abilities of the wakeboarder or water- skier. Keep the person being pulled at least 50 m (164 ft), about twice the distance of a standard tow-rope, away from any potential hazard.● Theoperatorsofboatsandotherwatercraft may not be aware that you are pulling a wakeboarder or water-skier. Together with the spotter, pay attention to others around you and cruise at safe speeds.● Be alert to the hazard of the tow-rope han- dle snapping back at the boat when the wakeboarder or water-skier falls or is un- able to get up on the skis.16]]></page><page Index="23" isMAC="true"><![CDATA[Rules of the roadYour Yamaha boat is legally considered a powerboat. Operation of the boat must be in accordance with the rules and regula- tions governing the waterway on which it is used.Just as there are rules that apply when you are driving on streets and highways, there are waterway rules that apply when you are oper- ating your boat. These rules are used interna- tionally, and are also enforced by the United States Coast Guard and local agencies. You should be aware of these rules, and follow them whenever you encounter another vessel on the water.Several sets of rules prevail according to geo- graphic location, but are all basically the same as the International Rules of the Road. The rules presented here in this owner’s/opera- tor’s manual are condensed, and have been provided for your convenience only. Consult your local U.S. Coast Guard Auxiliary or De- partment of Motor Vehicles for a complete set of rules governing the waters in which you will be operating your boat.Steering and sailing rulesWhenever two vessels on the water meet one another, one vessel has the right-of-way; it is called the “stand-on” vessel. The vessel that does not have the right-of-way is called the “give-way” or “burdened” vessel. These rules determine which vessel has the right-of-way, and what each vessel should do.Stand-on vesselThe vessel with the right-of-way has the duty to continue its course and speed, except to avoid an immediate collision. When you main- tain your direction and speed, the other vessel will be able to determine how best to avoid you.Safety informationGive-way vesselThe vessel which does not have the right-of- way has the duty to take positive and timely action to stay out of the way of the stand-on vessel. Normally, you should not cross in front of the vessel with the right-of-way. You should slow down or change directions briefly and pass behind the other vessel. You should al- ways move in such a way that the operator of the other vessel can see what you are doing. The General Prudential Rule regarding the right-of-way is that if a collision appears un- avoidable, neither boat has the right-of-way. Both boats must avoid the collision.In other words, follow the standard rules ex- cept when a collision will occur unless both vessels try to avoid each other. If that is the case, both vessels become give-way vessels. Rules when encountering vesselsThere are three main situations that you may encounter with other vessels which could lead to a collision unless the Steering Rules are fol- lowed:Meeting: you are approaching another vessel head-on.Crossing: you are traveling across another vessel’s path.Overtaking: you are passing or being passed by another vessel.17]]></page><page Index="24" isMAC="true"><![CDATA[Safety informationIn the following illustration, your boat is in the center. You should give the right-of-way to any vessels shown in the white area (you are the give-way vessel). Any vessels in the shad- ed area must yield to you (they are the give- way vessels). Both you and the meeting ves- sel must alter course to avoid each other.CrossingWhen two power-driven vessels are crossing each other’s path close enough to run the risk of collision, the vessel which has the other on the starboard (right) side must keep out of the way of the other. If the other vessel is on your starboard (right) side, you must keep out of its way; you are the give-way vessel. If the other vessel is on your port (left) side, remember that you should maintain course and direction, provided the other vessel gives you the right- of-way, as it should.MeetingIf you are meeting another power-driven ves- sel head-on, and are close enough to run the risk of collision, neither of you has the right-of- way. Both of you should alter course to avoid an accident. You should keep the other vessel on your port (left) side. This rule does not ap- ply if both of you will clear one another if you continue on your set course and speed.OvertakingIf you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and direction so that the other vessel can steer itself around you.18]]></page><page Index="25" isMAC="true"><![CDATA[Other special situationsThere are three other rules you should be aware of when operating your boat around other vessels.Narrow channels and bendsWhen navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a power- driven vessel is preparing to go around a bend that may obstruct the view of other water vessels, the operator should sound a pro- longed blast of four to six seconds on the horn. If another vessel is around the bend, it too should sound the horn. Even if no reply is heard, however, the vessel should still pro- ceed around the bend with caution.Fishing vessel right-of-wayAll vessels fishing with nets, lines, or trawls are considered to be “fishing vessels” under the International Rules. Vessels with trolling lines are not considered fishing vessels. Fish- ing vessels have the right-of-way regardless of position. Fishing vessels cannot, however, impede the passage of other vessels in nar- row channels.Sailing vessel right-of-waySailing vessels should normally be given the right-of-way. The exceptions to this are:(1) Whenthesailingvesselisovertakingthepower-driven vessel, the power-drivenvessel has the right-of-way.(2) Sailingvesselsshouldkeepclearofanyfishing vessel.(3) In a narrow channel, a sailing vesselshould not hamper the safe passage of a power-driven vessel that can navigate only in such a channel.Reading buoys and other markersThe waters of the United States are marked for safe navigation by the lateral system of buoyage. Simply put, buoys and markers have an arrangement of shapes, colors, num-Safety informationbers, and lights to show which side of the buoy a boater should pass on when navigat- ing in a particular direction. The markings on these buoys are oriented from the perspective of being entered from seaward (the boater is going towards the harbor). Red buoys are passed on your starboard (right) side when proceeding from open water into port, and black buoys are to your port (left) side. An easy way to remember the meaning of the colors is the phrase “red right returning.” When navigating out of the harbor, your posi- tion with respect to the buoys should be re- versed; red buoys should be to port and black buoys to starboard.Many bodies of water used by boaters are en- tirely within the boundaries of a particular state. The Uniform State Waterway Marking System has been devised for these waters.19]]></page><page Index="26" isMAC="true"><![CDATA[Safety informationThis system uses buoys and signs with distinctive shapes and colors to show regulatory or ad- visory information. These markers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information.Remember, markings may vary by geographic location. Always consult local boating authori- ties before riding your boat in unfamiliar waters.20]]></page><page Index="27" isMAC="true"><![CDATA[To get more boating safetyinformationBe informed about boating safety. Additional publications and information can be obtained from many organizations, including the follow- ing.United States Coast GuardConsumer Affairs Staff (G-BC)Office of Boating, Public, and Consumer Af- fairsUS Coast Guard HeadquartersWashington, D.C. 20593-0001 http://www.uscgboating.orgOther sourcesYou can find local rules by contacting the Na- tional Association of State Boating Law Ad- ministrators, or your local Power Squadron. Boat Education and TrainingThe Online Boating Safety Course, available through the watercraft section of the yamaha- motor.com website, is a free, 50-question learning course available to the public. Upon successful completion of 80 percent or better, the user can request a certificate of comple- tion by mail or can download one immediate- ly. The Online Boating Safety Course, provided by the Boat/US Foundation, is ap- proved by the National Association of State Boating Law Administrators (NASBLA) and recognized by the United States Coast Guard. This course meets the education re- quirement for those states that recognize non- proctored, NASBLA-approved courses.Safety informationEnjoy your boat responsiblyYou share the areas you enjoy when operat- ing your boat with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, wa- ters, and wildlife with respect and courtesy. Whenever and wherever you are boating, think of yourself as the guest of those around you. Remember, for example, that the sound of your boat may be music to you, but it could be just noise to others. And the exciting splash of your wake can make waves others won’t enjoy. Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife areas, and keep a respectful distance from fishermen, other boats, swimmers, and populated beaches. When travel in areas like these is unavoidable, operate slowly and obey all laws.Remember that pollution can be harmful to the environment. Do not refuel or add oil where a spill could cause damage to nature. Keep your surroundings pleasant for the peo- ple and wildlife that share the waterways: don’t litter!When you go boating responsibly, with re- spect and courtesy for others, you help en- sure that our waterways stay open for the enjoyment of a variety of recreational opportu- nities.The Online Boating Safety Course: http://www.boatus.org/21]]></page><page Index="28" isMAC="true"><![CDATA[DescriptionBoat glossaryTERMBowDeckGive-wayGunwaleHatchHelmHullLanyardPFDPlaningPortStand-onStarboardSternSub-planingTransomTrollingWakeDEFINITIONThe front part of the boat.The “floor” or upper structure which covers the hull.The vessel that must yield the right-of-way when two boats meet.The meeting junction of the deck and hull; the upper edge around the boat. Pronounced “gunnel.”An opening in the deck that provides access below.The steering console.The basic part of the boat; the underside.The cord or tether that connects the operator to the engine shut-off switch so the engine will stop if the operator accidentally leaves the helm.A personal flotation device, also known as “life jacket.”Traveling at a speed fast enough so the boat has leveled out and is skimming on top of the water. There is a wake.The left side of the boat.The vessel with the right-of-way when two boats meet.The right side of the boat.The back part of the boat.Traveling at a medium speed. The bow of the boat is out of the water, but you are still traveling through the water. There is a wake.The vertical part of the stern.Traveling at idle speed, using little or no throttle. The boat is down in the water and it is not leaving a wake.The visible track of disturbed water that the boat leaves behind as it moves in the water.22]]></page><page Index="29" isMAC="true"><![CDATA[210 FSH Deluxe/210 FSHDescriptionLocation of main components Exterior components65 342 1712 16 15142 139833 12 11101 Front starboard seat (page 52)2 Handgrip3 Rod holder (page 60)4 Front console seat (page 52)5 Windshield (page 63)6 Anchor light (page 48, 64)7 Fuel tank filler cap (page 74)8 Leaning post (page 52)9 Jump seat (page 52)10 Courtesy light (page 48)11 Speaker12 Cleat13 Front port seat (page 52)14 Bow light (page 48)15 Anchor storage compartment (page 53) 16 Bow eye23]]></page><page Index="30" isMAC="true"><![CDATA[Description 210 FSH Sport76 534832 1914 18 17162 15311 10 3 14 13121 Front starboard seat (page 52)2 Handgrip3 Rod holder (page 60)4 Front console seat (page 52)5 T-top (page 70)6 Windshield (page 63)7 Bimini top (page 70)8 Anchor light (page 48, 64)9 Fuel tank filler cap (page 74)10 Leaning post (page 52)11 Jump seat (page 52)12 Courtesy light (page 48)13 Speaker14 Cleat15 Front port seat (page 52)16 Bow light (page 48)17 Anchor storage compartment (page 53) 18 Bow eye24]]></page><page Index="31" isMAC="true"><![CDATA[Description8 746 453 2192 810 4111213 41615 14 241 Swim platform (page 66)2 Cleat3 Wet storage compartment (page 59)4 Rod holder (page 60)5 Ski tow hook6 Engine hood (page 53)7 Enclosed storage compartment (page 57)8 Handgrip9 Bow light (page 48)10 Speaker11 Courtesy light (page 48)12 Cooling water pilot outlet (page 90)13 Bilge pump outlet (page 78)14 Jump seat (page 52)15 Livewell (page 61)16 Reboarding grip25]]></page><page Index="32" isMAC="true"><![CDATA[Description Stern components1234156657117988 101 Cleat2 Reboarding grip3 Ski tow hook4 Ladder (page 66)5 Stern eye6 Shift gate (page 32)7 Jet thrust nozzle8 Intake grate9 Speed sensor10 Hull drain plug (page 78)11 Articulating keel (page 33)26]]></page><page Index="33" isMAC="true"><![CDATA[DescriptionHelm components12131211810 9 74561 Tachometer (page 35)2 Multi-function display unit (page 35)3 Compass4 Stereo receiver (page 51)5 Handgrip6 Storage pocket (page 59)7 Remote control lever (page 32)8 Jet wash switch (page 47)9 No-wake mode/cruise assist switch (page 47)10 Tilt lever (page 34)11 Glove compartment (page 58)12 Steering wheel (page 33)27]]></page><page Index="34" isMAC="true"><![CDATA[Description123 422NAV/ ANCCTSY ACC ACC LIGHTSMNLAERATORAUTOLIVEWELLBILGE HORNBLOWER6 7 8 9 10111213512VAUDIO AUX-USB1615 141 Main switch (page 31)2 Switch circuit breaker (page 50)3 Engine shut-off switch (page 30)4 Engine shut-off cord (lanyard) (page 30)5 Blower switch (page 47)6 Navigation and anchor lights switch (page 48)7 Courtesy light switch (page 48)8 Accessory switch 1 (page 47)9 Accessory switch 2 (page 47)10 Aerator switch (page 47)11 Livewell switch (page 47)12 Bilge pump switch (page 47)13 Horn switch (page 47)14 Aux input (page 51)15 12 V DC outlet (page 51)16 Switch circuit breaker (page 51)28]]></page><page Index="35" isMAC="true"><![CDATA[DescriptionEngine components12 31243 451 Blower (page 88)2 Oil tank filler cap/Dipstick (page 75)3 Spark plug/Ignition coil4 Air filter case5 Fuse box (cover) (page 124)29]]></page><page Index="36" isMAC="true"><![CDATA[Control function operationBoat control functions Engine shut-off switch● Always attach the engine shut-off cord (lanyard) to your PFD before starting the engine. Failure to attach the cord could result in a runaway boat if the operator is ejected.● Do not attach the cord to clothing that could tear loose. Do not route the cord in such a way that it could become entan- gled, preventing it from functioning.● Avoid accidentally pulling the cord dur- ing normal operation. Once the engine has stopped, you have no steering con- trol of the boat which could result in an accident. Also, without engine power, the boat could slow rapidly from planing speed. This could cause people and ob- jects in the boat to be thrown forward, which could cause injury.The clip on the end of the engine shut-off cord (lanyard) must be attached to the engine shut- off switch for the engine to run. The cord must be attached to a secure place on the opera- tor’s PFD. Should the operator fall overboard or leave the helm, the cord will pull out the clip, stopping the ignition to the engine. This will prevent the boat from running away under power.1 Engine shut-off switch2 Clip3 Engine shut-off cord (lanyard)Battery switchesThe batteries and switch assembly are locat- ed in the battery compartment.This boat uses two marine batteries. One bat- tery is designated as the start battery. The start battery is connected to the starter circuit on the engine to provide current for the starter motor.The other battery is designated as the house battery. The house battery provides power for the various accessory circuits on the boat, such as the circuits for the lighting, bilge pump, blowers and audio system.123WARNING123301 Battery switch assembly2 Start battery3 House battery]]></page><page Index="37" isMAC="true"><![CDATA[There are three switches on the battery switch assembly: the “START” switch, “HOUSE” switch, and “EMERG PARALLEL” switch.tion to start the engine. Once the engine is started or the start battery is charged, turn the “EMERG PARALLEL” switch to the OFF posi- tion.Main switchesThere is a main switch for each engine.The main switch controls the ignition and electrical circuits as follows:1 “HOUSE” switch (red)2 “EMERG PARALLEL” switch (yellow)3 “START” switch (red)Control function operation1231 2OFF START ONBLOWER121 ON position (green)2 OFF position (red)In normal operation, keep the “START” and “HOUSE” switches in the ON position. Keep the “EMERG PARALLEL” switch in the OFF position. This setting allows both batteries to be charged automatically while the engine is running. NOTICE: Do not turn the “HOUSE” switch to the OFF position if the boat is moored in the water as it will prevent the bilge pump and anchor light from func- tioning.If the start battery is discharged, turn the “EMERG PARALLEL” switch to the ON posi-1 Main switch (port engine)2 Main switch (starboard engine)OFF:Ignition circuit is switched off. The engine can- not be started, but other switches will operate. (The main switch key can be removed.)ON:Ignition circuit is switched on. (The main switch key cannot be removed.)START:The starter motor will turn to start the engine. (When the main switch key is released, it re- turns automatically to “ON”.)TIP:● Theenginewillnotstartwhentheclipisre- moved from the engine shut-off switch. The starter motor will turn over without the cord attached.● Themainswitchwillnotoperate(thestarter motor will not turn over) if the “START” switch in the battery compartment is turned31]]></page><page Index="38" isMAC="true"><![CDATA[Control function operationto the OFF position. (See page 30 for more information.)Remote control levers● Before shifting, make sure there are no swimmers or obstacles in the water near you.● When operating in reverse, go slowly. Do not open the throttle more than half. Otherwise, the boat may become unsta- ble, which could result in loss of control and an accident.● Do not shift into reverse while traveling at planing speeds. Loss of control, boat swamping, or damage to the boat could occur.The remote control lever for each engine con- trols both throttle and shifting. In normal oper- ation, the levers are moved together.Moving the remote control levers forward from the neutral position shifts into the forward po- sition, and then as the levers are moved far- ther, accelerates the engines for more thrust. Moving the levers back from the neutral posi- tion shifts into the reverse position, and then as the levers are moved farther, accelerates the engines for more thrust.For cruising, adjust the remote control levers so both engines are running at the same en- gine speed.TIP:Because of the mechanical throttle linkage, the remote control levers may not be exactly even with one another when the engines are running at the same engine speed.1 Neutral position2 TDE position3 Forward position4 Reverse position5 Shift6 Fully closed7 Throttle8 Fully openTIP:This boat is equipped with a “start-in-gear” protection. The engines will not start unless the levers are in the neutral position.This boat uses a direct-drive propulsion sys- tem. Therefore, jet thrust is always being pro- duced while the engines are running. The direction of the boat is controlled by the shift gates, which direct the flow of the jet thrust as follows:NeutralThe shift gates are dropped down part way over the jet thrust nozzles. The neutral posi- tion balances forward and reverse thrust to help keep the boat from moving, although some movement may occur.F2 N1 R 55347667 88WARNING32]]></page><page Index="39" isMAC="true"><![CDATA[Control function operation1 21 212121 Shift gate2 Jet thrust nozzleForwardWhen the remote control levers are initially moved to the forward position and the boat is operating at a slow speed, the shift gates are lifted up slightly from the neutral position and jet thrust is directed downward at an angle. This function, which is called the thrust direc- tional enhancer (TDE), helps to provide good handling response when the steering wheel is turned, even though there is less thrust avail- able at low engine speeds.1 Shift gate2 Jet thrust nozzleReverseThe shift gates are dropped all the way down over the jet thrust nozzles. Jet thrust is redi- rected toward the bow of the boat, which moves the boat backward.1N F1R1 TDE positionWhen the remote control levers are moved farther forward, the shift gates are lifted all the way up. All jet thrust is to the rear, which moves the boat forward.1 Shift gateSteeringYour boat can be steered by turning the steer- ing wheel the same direction you wish to trav- el, to the right or left. When the steering wheel is turned, the angle of the jet thrust nozzles at the rear of the craft is changed, and the change in direction of the jet thrust nozzles changes the direction of the boat accordingly. In addition, the direction of the articulating keel changes according to the movement of the jet thrust nozzles.33]]></page><page Index="40" isMAC="true"><![CDATA[Control function operationTilt leverWARNING●●Never touch the tilt lever during opera- tion, otherwise the steering wheel could suddenly change position, which may lead to an accident.Be sure the steering wheel is locked in position after adjustment. If the steering wheel is not locked in position, it may suddenly change position during opera- tion, which may lead to an accident.11 Steering wheelThe tilt lever is located under the steering wheel and is used to adjust the tilt of the steer- ing wheel. There are 5 positions.12111 Jet thrust nozzle2 Articulating keelSince the strength of the jet thrust determines the speed and direction of a turn, the throttle must always be opened above idle when at- tempting a turn, except at trolling speed. Because boats steer from the stern, the stern of the boat swings out in the opposite direction of your turn. If you turn to starboard, for exam- ple, the stern of the boat will swing to the left. Keep this in mind when navigating near a per- son in the water, such as a down wakeboard- er or water-skier, or an obstacle, such as a dock.1 Tilt leverTo adjust the tilt:(1) Pushtheleverdown,andthenmovethesteering wheel up or down to the desiredposition.(2) The lever will lock into place when thesteering wheel is moved into one of the 5available positions.(3) Makesurethatthetiltleverreturnstoitsoriginal position and that the steering wheel is securely locked in place.34]]></page><page Index="41" isMAC="true"><![CDATA[TachometersThe boat is equipped with two tachometers. The tachometer on the left is for the port en- gine. The one on the right is for the starboard engine.The analog tachometers show the engine speed. The numbers on the meters show the engine speed × 1000 rpm (r/min).12Instrument operation Multi-function display elements1210:15 am50% FuelPORT 1.5 Hrs- Float Mode -12.4 VSTBD 1.6 HrsWater77˚FSTBD 1.6 Hrs6543PORT 1.5 HrsSTBD 1.6 Hrs7NameFunction1Screen tab barShows the 3 tabs for the screens that can be displayed on the multi- function display. (See page 36.)2Center displayShows various infor- mation and settings for each screen.3Title barShows the title of the currently selected screen. This bar will appear only if there are no current warnings.4Right arrowTap this arrow to change the informa- tion displayed in the data bar.5Data barShows various types of data. This bar will ap- pear only if there are no current warnings. The displayed data can be changed by tapping the left arrow or right arrow. (See the “Data bar”.)1 Port tachometer2 Starboard tachometerMulti-function display unit operationBecause the multi-function display unit is equipped with a touch screen, you can touch the display directly to operate the display functions.Touching the multi-function display35]]></page><page Index="42" isMAC="true"><![CDATA[Instrument operationNameFunction6Left arrowTap this arrow to change the informa- tion displayed in the data bar.7Warning barShows current warn- ings. This bar will ap- pear only if there are current warnings. If there are no current warnings to display, it will be replaced by the data bar and the title bar.Screen tabs (screen tab bar)1 Home screen tab2 Trip screen tab3 Setting screen tabThe tab for the currently displayed screen is shown in green.Data bar1 Data bar2 Right arrow3 Left arrowThe data bar can display the following infor- mation.TIP:To change the information displayed in the data bar, tap the left arrow or right arrow. Theinformation displayed in the data bar changes in the following order:Average fuel consumption → Trip distance → Fuel rate → Fuel used → Port engine hours → Starboard engine hours → Water temperatureAverage fuel consumptionThis display shows the average distance that can be traveled on 1.0 gallon or 1.0 liter of fu- el.Trip distanceThis display shows the distance traveled by the boat in miles or kilometers.Fuel rateThis display shows the total fuel consumption of the port and starboard engines in gallons per hour or liters per hour.Fuel usedThis display shows the total fuel that has been consumed by the port and starboard engines in gallons or liters.Engine hours (port and starboard)This display shows the total number of hours that the port and starboard engines have been running since the boat was new.Water temperatureThis display shows the ambient water temper- ature in degrees Fahrenheit or degrees Cel- sius.Information display (home screen tab)The home screen can display various types of information.The information that can be displayed varies depending on whether one of the engines is running.12310:15 amPORT - Settings - STBD 1.5 Hrs 1.6 HrsSTBD 1.6 Hrs36312]]></page><page Index="43" isMAC="true"><![CDATA[When both engines are not running:The screen displays the fuel level, water tem- perature, engine hours, and other information.Instrument operationNameFunction7Port engine hoursShows the total num- ber of hours that the port engine has been running since the boat was new.1234510:15 am77˚F50% FuelPORT 1.5 HrsWater12.4 VSTBD 1.6 Hrs- Float Mode - STBD 1.6 Hrs76When one engine or both engines are run- ning:The screen displays the boat speed, engine speed, and operating status of the cruise as- sist, no-wake mode and jet wash system.1210:15 am50% FuelPORT15 X100 RPM3.0 MPHNo Wake Mode- Running Mode - STBD 1.6 Hrs12.4VSTBD15 X100 RPM43NameFunction1ClockShows the time.2Fuel level bar graphShows the amount of fuel remaining in the fuel tank. Depending on the amount of re- maining fuel, the bar graph is displayed in 3 colors: green, orange, and red.3Water tempera- tureShows the ambient wa- ter temperature in de- grees Fahrenheit or degrees Celsius.4Voltage level bar graphShows the battery volt- age of the boat bat- tery. Depending on the battery voltage level, the bar graph is dis- played in 3 colors: green, orange, and red.5MuteMutes the sound of the buzzer for a specific time depending on the warnings present.6Starboard en- gine hoursShows the total num- ber of hours that the starboard engine has been running since the boat was new.NameFunction1Boat speedShows the boat speed in miles per hour or ki- lometers per hour.2Cruise assist and no-wake mode and jet wash system statusShows the operating status of the cruise as- sist and no-wake mode and jet wash system.3Starboard en- gine speedShows the engine speed of the starboard engine.4Port engine speedShows the engine speed of the port en- gine.Cruising information display (trip screen tab)The trip screen can display 4 types of trip-re- lated information at the same time.37]]></page><page Index="44" isMAC="true"><![CDATA[Instrument operation123410:15 am502.1 AVG mpg 26.3 Miles0.0 GpH12.5 Gal - Trip Info - STBD 1.6 Hrs12STBD 1.6 Hrs% Fuel.4VPORT 1.5 Hrs12110:15 am50% FuelPORT 1.5 HrsTime UnitPort WellnessBrightness LanguageStbd Wellness12.4 VSTBD 1.6 Hrs- Settings - STBD 1.6 HrsNameFunction1Average fuel consumptionShows the average dis- tance that was trav- eled on 1.0 gallon or 1.0 liter of fuel since the item was last reset.2TripShows the distance traveled by the boat in miles or kilometers since the item was last reset.3Total fuel rate*Shows the total fuel consumption of the port and starboard en- gines in gallons per hour or liters per hour.4Total fuel usedShows the total fuel that has been con- sumed by the port and starboard engines in gallons or liters since the item was last reset.* This item cannot be reset.1 Menu2 “ ”buttonUse this screen to change the following set- tings:● Time● Unit● PortWellness ● Brightness● Language● StbdWellness ● Aerator● ResetTIP:The menu displays 6 items at one time. Tap the “ ” button on the screen to scroll through the menu items.Setting the timeTap the “ Time ” button to set the time. Tap the time unit that you want to set and flick up or down.To reset an item on the cruising information display:Touch and hold the item that you want to reset for several seconds.Multi-function display unit settings (setting screen tab)The setting screen can be used to change the settings of the multi-function display unit.38]]></page><page Index="45" isMAC="true"><![CDATA[Instrument operation123410:15 am50% FuelPORT 1.5 Hrs- Time - STBD 1.6 Hrs12.4 VSTBD 1.6 Hrs9 10 : 11Set Time012456pm am pmStarboard/port engine wellness displayTap the “ Stbd Wellness ” button or “ Port Wellness ” button to display the total num- ber of hours that the engine has been running since the last maintenance.1210:15 am50% FuelPORT 1.5 HrsTime Since Last MaintenanceRESET- Stbd Wellness - STBD 1.6 Hrs12.4 VSTBD 1.6 Hrs1.5 Hrs1 Hours2 Ten minutes3 Minutes4 AM/PM (Imperial mode only)TIP:When “IMPERIAL” is selected, the time is dis- played in the 12-hour format. When “METRIC” is selected, the time is displayed in the 24-hour format.Selecting the display unitsTap the “ Unit ” button to select “ IMPERIAL ” or “ METRIC ” for the display units.1 Hours of engine operation2 “RESET” buttonTo reset the engine hours: (1) T ap the“ ” button. (2) Tap the “confirmation screen.” button on theRESETARE YOU SURE?1210:15 am50% FuelPORT 1.5 HrsUnit METRICIMPERIAL- Unit - STBD 1.6 Hrs12.4 VSTBD 1.6 Hrs110:15 am50% FuelPORT 1.5 HrsTime Since Last Maintenance12.4 V ARE YOU SURE?1.5 Hrs- Stbd Wellness - STBD 1.6 HrsSTBD 1.6 Hrs1 “METRIC” button2 “IMPERIAL” buttonTapthe“IMPERIAL ”buttonor“METRIC ”button to select the desired display unit setting. TIP:The default setting is “IMPERIAL”.1 “ARE YOU SURE?” buttonSetting the day mode and night modeThe multi-function display has a day mode and a night mode.When the bow light or anchor light is turned on, the multi-function display will enter the39]]></page><page Index="46" isMAC="true"><![CDATA[Instrument operationnight mode and the display brightness will de- crease.Tap the “ Brightness ” button to adjust the brightness of the display. The brightness can be set separately for the day mode and for the night mode.To adjust the brightness:(1) Tap the “ DAY ” button or “ NIGHT ” button110:15 am50% FuelPORT 1.5 HrsLanguage- Language - STBD 1.6 Hrs12.4 VSTBD 1.6 Hrsto select the desired mode.12310:15 am50% FuelPORT 1.5 HrsBrightness DAY 100% NIGHT- Brightness - STBD 1.6 Hrs12.4 VSTBD 1.6 Hrs1 Display languagesTIP:The available display languages are English, French, and Spanish.Setting the aeration time (aerator button)Tap the “ Aerator ” button to set the on and off time settings for the aerator.1 “DAY” button2 “NIGHT” button3 Slider control31210:15 am50% FuelPORT 1.5 HrsAerator12.4 VSTBD 1.6 HrsTime ON 2 Time OFF min- Auto Aerator Sett - STBD 1.6 Hrs(2) To make the display darker, drag the slid- er to the left. To make the display bright- er, drag the slider to the right.TIP:● The default settings are 100% for the day mode and 50% for the night mode.● When the brightness of the multi-function display is adjusted, the brightness of the ta- chometers is also adjusted accordingly.Setting the display languageTap the “ Language ” button to change the se- lected display language.1 “Time ON” button 2 “Time OFF” button 3 Slider control● When the “ Time ON ” button is tapped, the slider moves to the current on time setting. Default: 2 minutes● When the “ Time OFF ” button is tapped, the slider moves to the current off time setting. Default: 1 minutes40]]></page><page Index="47" isMAC="true"><![CDATA[Instrument operationTIP:To increase the time setting, drag the slider to the right. To decrease the time setting, drag the slider to the left.Resetting the settings to the default settingsTap the “ RESET ” button to reset the settings to their factory default settings.The default settings are as follows:● Aerator: ON 2 minutesOFF 1 minutes● Day mode brightness: 100%● Night mode brightness: 50%● Unit: IMPERIAL● Language:English1 “YES” buttonNo-wake mode/cruise assist switchThis switch activates and sets the no-wake mode, cruise assist, and reverse RPM con- trol.110:15 am50% FuelPORT 1.5 HrsAre you sure?YES- Reset to Factory - STBD 1.6 Hrs12.4 VSTBD 1.6 Hrs(1)Tap the “ RESET” button.110:15 am50% FuelPORT 1.5 HrsReset To Factory? RESET- Reset to Factory - STBD 1.6 Hrs12.4 VSTBD 1.6 HrsJET WASH11(2)“RESET” buttonTap the “ YES screen.” button on the confirmationTo operate the no-wake mode and cruise as- sist, see the following sections. To activate the reverse RPM control, see “Reverse RPM control” on page 43.Operating the boat with a minimal wake (no-wake mode)The no-wake mode is useful for operating the boat at a steady speed with a minimal wake. This is especially convenient when traveling in harbors, channels, or other areas posted with low speed limits as “no wake zones”.1 No-wake mode/cruise assist switch41]]></page><page Index="48" isMAC="true"><![CDATA[Instrument operationThe no-wake mode can be used only when the engines are operating at idle speed.To activate the no-wake mode:(1) Put the remote control levers in the TDEposition or forward position so that bothengines are operating at idle speed.(2) Push the plus side of the no-wake mode/cruise assist switch. Once “No Wake Mode” is displayed in the multi- function meter, the no-wake mode is acti-vated.available for use whenever the engines are running above 4000 rpm and below 7000 rpm.T o (1)(2)activate the cruise assist:Push the remote control levers forward to open the throttle until the desired engine speed is reached and both engines are operating at the same engine speed. Push the plus side or minus side of the no-wake mode/cruise assist switch. Once “Cruise” is displayed in the multi- function meter, the cruise assist is acti- vated.10:15 am50% FuelPORT15 X100 RPM3.0 MPH- Running Mode - STBD 1.6 Hrs12.4VSTBD15 X100 RPMNo Wake Mode10:15 am50% FuelPORT35 X100 RPM5.8 MPHCruise +1 - Running Mode -STBD 1.6 Hrs12.4VSTBD35 X100 RPMTIP:The no-wake mode can be set to 3 engine speeds. To adjust the engine speed while the no-wake mode is activated, push the plus side or minus side of the no-wake mode/cruise as- sist switch.To deactivate the no-wake mode: Perform one of the following operations.● Push the minus side of the no-wakemode/cruise assist switch until “No WakeMode” disappears.● Push the remote control levers forward toopen the throttle.Operating the boat at a steady speed (cruise assist)The cruise assist feature is for steady engine speed operation when the boat is traveling above no-wake speeds. The cruise assist isTIP:● Once the cruise assist is activated, the set engine speed can be increased by pushing the plus side of the switch or decreased by pushing the minus side. However, the ad- justment is limited to a maximum of 8 incre- ments above or below the initial cruise assist setting. Each time the switch is pushed, the engine speed will increase or decrease approximately 100–200 rpm.● While the cruise assist is activated, the en- gine speed can also be adjusted by operat- ing the remote control levers.T o deactivate the cruise assist:Operate the remote control levers to decrease the engine speed to 3000 rpm or less. Once42]]></page><page Index="49" isMAC="true"><![CDATA[“Cruise” disappears, the cruise assist is deac- tivated.Operating the boat in reverse with more thrust (reverse RPM control) Engine speed in reverse is limited to approxi- mately 4500 rpm. If more thrust is required when the boat is traveling in reverse, use the reverse RPM control. WARNING! Be pre- pared to reduce throttle as soon as the boat moves as desired. Otherwise, the boat may become unstable, which could result in loss of control and an accident. To activate the reverse RPM control:(1) Movetheremotecontrolleversbackward so that the throttle is opened in reverse and both engines are operating at the same engine speed.(2) Increase the engine speed to 4500 rpm, and then push the plus side of the no- wake mode/cruise assist switch.TIP:Once the reverse RPM control is activated, pushing the plus side of the no-wake mode/cruise assist switch will increase the available engine speed by approximately 500 rpm in 3 stages up to a maximum of 6000 rpm, and pushing the minus side will de- crease the available engine speed. However, the adjustment is limited to these 3 incre- ments.To deactivate the reverse RPM control: Operate the remote control levers to decrease the engine speed to less than 4500 rpm.WarningsIf a malfunction or fault occurs, a warning buzzer will sound and a warning icon and warning message will be displayed on the center display.Instrument operationThe check engine warning indicator is also displayed on the tachometer for the engine with the warning.12310:15 am50% FuelPORT 1.5 HrsPort Engine: Over Temperature Stbd Engine: Over Temperature12.4 VSTBD 1.6 Hrs1 Warning message2 Warning icon3 Mute button11MNLNAV/ CTSY ACC ACC AERATOR LIVEWELL B ANC LIGHTSAUTO1 Check engine warning indicatorWarning definition tableThe warnings that are displayed on the multi- function display are listed in the following ta- ble.Warning iconWarning messagePort Engine Check EngineCheck engine warningStbd Engine Check EnginePort Engine Low Oil PressureLow oil pressure warn- ingStbd Engine Low Oil Pressure43]]></page><page Index="50" isMAC="true"><![CDATA[Instrument operationCheck engine warningIf an engine sensor malfunction or a short cir- cuit is detected, a warning will appear on the multi-function display and the buzzer will sound. If a fault is detected for the port engine, “Port Engine Check Engine” will be displayed and if a fault is detected for the starboard en- gine, “Stbd Engine Check Engine” will be dis- played. If this occurs, reduce the engine speed, return to shore, and have a Yamaha Boat Dealer check the engine.Low oil pressure warningIf the oil pressure does not rise to specifica- tion, a warning will appear on the multi-func- tion display and the buzzer will sound. If a fault is detected for the port engine, “Port En- gine Low Oil Pressure” will be displayed and if a fault is detected for the starboard engine, “Stbd Engine Low Oil Pressure” will be dis- played. At the same time, the engine speed is automatically limited to help prevent damage. If this occurs, reduce the engine speed, return to shore or maneuver to a safe location, and check the engine oil level. (See page 75 for engine oil level checking procedures.)If the oil level is low, add enough engine oil to raise it to the proper level. If the oil level is suf- ficient, have a Yamaha Boat Dealer check the engine.Over temperature warningThis model is equipped with an over tempera- ture warning system. If the engines start to overheat, a warning will appear on the multi- function display and the buzzer will sound. If the port engine is overheating, “Port Engine Over Temperature” will be displayed and if the starboard engine is overheating, “Stbd En- gine Over Temperature” will be displayed. At the same time, the engine speed is automati-Warning iconWarning messageOver temperature warningPort Engine Over TemperatureStbd Engine Over TemperatureGeneric WarningPort Engine Commu- nication ErrorStbd Engine Commu- nication ErrorEngine CAN Commu- nication ErrorPort Gauge Communi- cation ErrorStbd Gauge Commu- nication ErrorLIN Communication ErrorLow FuelStbd Engine time since last mainte- nancePort Engine time since last maintenanceHigh Battery VoltageLow Battery Voltage44]]></page><page Index="51" isMAC="true"><![CDATA[cally limited to help prevent damage. If this oc- curs, immediately reduce the engine speed, return to shore or maneuver to a safe location, and check for water discharge at the cooling water pilot outlets. There are cooling water pi- lot outlets on the starboard side of the hull. Check that water comes out of the outlets while the engines are running, particularly while applying throttle. If you do not see any water at the outlets, cooling water may not be circulating in the engines.1 Intake grate NOTICEIf the cause of overheating cannot be found and corrected, take special precau- tions to avoid major engine damage while you return to shore.Single engine overheating — Shut off the overheating engine and use the properly running engine to return to shore. Operate at no-wake speed (8 km/h, 5 mph) to pre- vent water from flooding the non-operat- ing engine through the water intake. See page 41 for information on the no-wake mode.Both engines overheating — If getting a tow from another vessel is not possible, operate both engines just slightly above idle while you return to shore. If you can be towed, refer to “Towing the boat” on page 126.Instrument operation1121 Cooling water pilot outlet (starboard engine)2 Cooling water pilot outlet (port engine)TIP:If the cooling water passages in the engines are dry, it will take about 20 seconds for water to reach the pilot outlets after starting.If water is not circulating, something may be clogging the intake grates. Refer to “Jet pump clean-out procedure” on page 122.45]]></page><page Index="52" isMAC="true"><![CDATA[Instrument operationGeneric warningIf a generic error is detected, a warning will appear on the multi-function display and the buzzer will sound. If this occurs, reduce the engine speed, return to shore, and have a Yamaha Boat Dealer check the boat.When a generic error is detected, the follow- ing warning messages are displayed.● PortEngineCommunicationError● StbdEngineCommunicationError● EngineCANCommunicationError ● PortGaugeCommunicationError ● StbdGaugeCommunicationError ● LINCommunicationError● LowFuel● StbdEnginetimesincelastmaintenance ● PortEnginetimesincelastmaintenance ● HighBatteryVoltage● LowBatteryVoltage46]]></page><page Index="53" isMAC="true"><![CDATA[Instrument operation SwitchesMNLNAV/ CTSY ACC ACC AERATOR LIVEWELL BILGE HORN ANC LIGHTSAUTO1234567811BLOWERJET 9 WASH10NameFunctionPage1Navigation and anchor lights switchTurns the anchor light and bow light on or off.482Courtesy light switchTurns the 2 courtesy lights and livewell light on or off.483Accessory switch 1These switches can be used to operate a fish finder or oth- er electronic device that is installed later as an accessory. For more information, contact a Yamaha Boat Dealer.—4Accessory switch 2—5Aerator switchCirculates the water in the livewell.496Livewell switchTurns the livewell pump on or off.617Bilge pump switchTurns the bilge pump on or off.788Horn switchActivates the horn. The horn can be used to signal other boats as required by the “Rules of the road”.179Jet wash switchTurns the jet wash system on or off.6710No-wake mode/cruise as- sist switchActivates and sets the cruise assist, no-wake mode, and reverse RPM control.4111Blower switchTurns the blower on or off to ventilate the engine compart- ment.8847]]></page><page Index="54" isMAC="true"><![CDATA[Instrument operationCourtesy light switchPush this switch to turn on the 2 courtesy lights on the sides of the console and the livewell light.Navigation and anchor lights switchThis toggle switch controls the bow light and anchor light. Push the upper side of the switch to turn on both the bow light and anchor light for night running (“NAV”). Push the lower side of the switch to operate the anchor light alone when anchored at night (“ANC”). Put the switch in the middle position to turn off all lights. (See page 64 for more information.)111 Courtesy light11 Bow light210 FSH Deluxe/210 FSH11 Courtesy light11 Livewell light481 Anchor light]]></page><page Index="55" isMAC="true"><![CDATA[Instrument operation210 FSH Sport11 Anchor lightAerator switchUse this switch to circulate the water in the livewell. Push the “MNL” side of the switch to circulate water continuously in the livewell. Push the “AUTO” side of the switch to circu- late water in the livewell according to the on and off operation settings. Put the switch in the middle position to stop circulating water. (See page 40 for information on setting the automatic operation settings.)49]]></page><page Index="56" isMAC="true"><![CDATA[Instrument operationSwitch circuit breakersThe electrical circuit for each switch is protected by a circuit breaker. If the button pops out, push it back in with your finger. If it pops out again, ask a Yamaha Boat Dealer to inspect the electrical system.11NAV/ ANCCTSY ACC ACC LIGHTSMNLAERATORAUTOLIVEWELLBILGE HORNJET WASHBLOWER11 Switch circuit breaker50]]></page><page Index="57" isMAC="true"><![CDATA[Accessory outletThere is a 12 V DC outlet with a circuit break- er located in the storage pocket.NOTICEDo not use an automotive cigarette lighter or other accessories that get hot because the outlet can be damaged.Instrument operationStereo systemA stereo receiver is standard. The stereo sys- tem consists of the receiver, speakers, auxil- iary input jack, USB terminal, and Bluetooth. Refer to the stereo system Operation Manual included with your boat.11212VAUDIO AUX-USB12V1 21 Circuit breaker2 12 V DC outlet1 Stereo receiver1 Auxiliary input jack2 USB terminal51]]></page><page Index="58" isMAC="true"><![CDATA[Equipment operation SeatsPassengers must always sit in a designat- ed seating area, place feet on the deck, and hold on to the handgrips when the boat is in motion.This boat is equipped with the following seats.Leaning postThe leaning post is a seat that is located in the center of the boat.There is a cooler box under the leaning post.WARNING12 32 131 Front starboard seat2 Front console seat3 Front port seat1 Strap2 Leaning post3 Cooler box210 FSH Sport/210 FSH Deluxe: The leaning post for these models is equipped with a backrest. The position of the backrest can be changed by pulling the strap toward the bow or toward the stern. By moving the backrest, you can change the seating position of the leaning post to face the bow or face the stern.Jump seatsThe 2 jump seats are located on the port and starboard sides of the boat near the stern.123121 Jump seat (starboard)2 Leaning post3 Jump seat (port)521 Jump seat (starboard)2 Jump seat (port)]]></page><page Index="59" isMAC="true"><![CDATA[Engine hoodThe engine hood can be opened to access the engine.The engine hood latches are located under the front of the leaning post.To open the engine hood, pull the engine hood latches up and lift the engine hood. NOTICE: Do not open the engine hood while the anchor light is installed. (210 FSH Deluxe/210 FSH) Otherwise, the an- chor light could be damaged.Equipment operationStorage compartmentsThis boat is equipped with the following con- venient on-board storage compartments. Make sure that the storage compartments are securely closed before getting underway.Anchor storage compartmentThe anchor storage compartment is located at the bow.T o open the anchor storage compartment: (1) Pull the lock handle up.(2) Turn the lock handle and then open the anchor storage compartment lid.21211 Engine hood latch2 Engine hoodTo close the engine hood, push the leaning post to securely lock it in place.1 Lock handle2 Anchor storage compartment lid11 Anchor storage compartmentWhen storing the anchor, place some cush- ioning material or the anchor line under the anchor.53]]></page><page Index="60" isMAC="true"><![CDATA[Equipment operationTo close the anchor storage compartment:(1) Close the anchor storage compartmentlid.(2) Turn the lock handle and make sure thatthe lid is securely closed.(3) Push the lock handle down.Bow storage compartmentThe bow storage compartment is located un- der the front port seat.To open a bow storage compartment: Unhook the latch, and then open the front port seat.To close the bow storage compartment: Close the front port seat, and then hook the latch on to the deck.Insulated fish boxThe fish box is located under the front star- board seat. It is insulated, and can be filled with some ice to help keep fish cold while boating. The box is self-draining.To open the fish box:Unhook the latch, and then open the front starboard seat.12121 Front port seat 2 Latch1 Front starboard seat 2 Latch111 Bow storage compartment1 Fish boxTo close the fish box:Close the front starboard seat, and then hook the latch onto the deck.54]]></page><page Index="61" isMAC="true"><![CDATA[Stern storage compartmentThe stern storage compartment is located un- der the jump seat (starboard).To open the stern storage compartment: Unhook the latch, and then open the stern storage compartment lid.Equipment operationLockable storage compartmentThe lockable storage compartment is located on the bow side of the console.The lockable storage compartment has a large compartment suitable for use as an on- board changing room and can also accommo- date a portable toilet (not included). WARNING! Do not open the lockable stor- age compartment while the boat is mov- ing. The lockable storage compartment lid could block your vision of others. In addi- tion, the lockable storage compartment lid could close unexpectedly due to the movement of the boat and you could be pinched. Carbon monoxide (CO) can cause brain damage or death. Carbon monoxide can be present in this compart- ment. Signs of carbon monoxide poison- ing include nausea, headache, dizziness, drowsiness, and lack of consciousness. Get fresh air if anyone shows signs of car- bon monoxide poisoning.To open the lockable storage compartment: While pulling the lockable storage compart- ment latch, lift the lockable storage compart- ment lid.121 Stern storage compartment lid 2 Latch1121 Stern storage compartmentTo close the stern storage compartment: Close the stern storage compartment lid, and then hook the latch on to the deck.1 Lockable storage compartment lid2 Lockable storage compartment latch55]]></page><page Index="62" isMAC="true"><![CDATA[Equipment operation1compartment11 Lockable storage compartment T o use the lockable storagelight:1 Drain plug(1)To turn on the lockable storage compart- ment light, push the light.1Lockable storage compartment light(2) Securely install the drain plug in its origi- nal position.T o close the lockable storage compartment: Push the lockable storage compartment lid down to securely lock it in place.To lock the lockable storage compartment:(1) Closethelockablestoragecompartment.(2) Insertthelockablestoragecompartmentkey into the keyhole of the lockable stor- age compartment latch, and then turn the key 90° clockwise.121(2)To drain water from the lockable storage com- partment:(1) Remove the drain plug on the bottom ofthe lockable storage compartment to drain the water.To turn off the light, push the light again.561 Lockable storage compartment key 2 KeyholeTIP:Store the lockable storage compartment key so that it is not lost.]]></page><page Index="63" isMAC="true"><![CDATA[T o unlock the lockable storage compartment: Insert the lockable storage compartment key into the keyhole of the lockable storage com- partment latch, and then turn the key 90° counterclockwise.Curtain/curtain rails (210 FSH Sport/210 FSH Deluxe)The curtain can be installed when the lock- able storage compartment is open.To install the curtain:(1) Insertthecurtainintothecurtainrails.Equipment operationT o remove the curtain:(1) Unsnap the buttons on the curtain fromthe button bases.(2) Remove the curtain from the curtain rails.Enclosed storage compartment (port)The enclosed storage compartment is a large storage compartment that is located on the port side of the boat.T o open the enclosed storage compartment: Pull the enclosed storage compartment door latch to open the door.12121 Curtain rail 2 Curtain(2) Snapthebuttonsonthecurtainontothe button bases on the lockable storage compartment.1 Enclosed storage compartment door latch 2 Enclosed storage compartment door1111 Button base1 Enclosed storage compartmentTo close the enclosed storage compartment: Close the enclosed storage compartment door, and then push it to securely lock it in place.57]]></page><page Index="64" isMAC="true"><![CDATA[Equipment operationEnclosed storage compartment (star- board)The enclosed storage compartment is a large storage compartment that is located on the starboard side of the boat.To open the enclosed storage compartment: Pull the enclosed storage compartment door latch to open the door.Glove compartmentThe glove compartment is located under the steering wheel.To open the glove compartment:Pull the glove compartment latch to open the glove compartment lid.12121 Enclosed storage compartment door latch2 Enclosed storage compartment door1 Glove compartment lid2 Glove compartment latch111 Enclosed storage compartmentTo close the enclosed storage compartment: Close the enclosed storage compartment door, and then push it to securely lock it in place.1 Glove compartmentT o close the glove compartment:Close the glove compartment lid, and then push it to securely lock it in place.To lock the glove compartment:(1) Closetheglovecompartment.(2) Inserttheglovecompartmentkeyintothekeyhole of the glove compartment latch, and then turn the key 90° clockwise.58]]></page><page Index="65" isMAC="true"><![CDATA[Equipment operationWet storage compartmentThe wet storage compartment is located un- der the swim platform.To open the wet storage compartment:(1) Pullthelockhandleup.(2) Turn the lock handle, and then open the rear platform hatch.1211 Keyhole2 Glove compartment keyTIP:Store the glove compartment key so that it is not lost.To unlock the glove compartment:Insert the glove compartment key into the keyhole of the glove compartment latch, and then turn the key 90° counterclockwise.Storage pocketThe storage pocket is located on the star- board side of the glove compartment.The storage pocket is equipped with an auxil- iary input jack and USB terminal for the stereo system, and a 12 V DC outlet.21 Rear platform hatch 2 Lock handle123412V11 Storage pocket2 12 V DC outlet3 Auxiliary input jack4 USB terminalTo close the wet storage compartment:(1) Closetherearplatformhatch.(2) Turn the lock handle and make sure thatthe hatch is securely closed. (3) Pushthelockhandledown. TIP:The engines will not start if the rear platform hatch is not securely closed.1 Wet storage compartment59]]></page><page Index="66" isMAC="true"><![CDATA[Equipment operationBucket storage compartmentThe bucket storage compartment is located in the center of the boat at the bow.To open the bucket storage compartment:(1) Pullthelockhandleup.(2) Turn the lock handle, and then open the bucket storage compartment lid.1121 Bucket storage compartment lid2 Lock handle1 Drain plug(2) Securelyinstallthedrainpluginitsorigi- nal position.To close the bucket storage compartment:(1) Closetherearplatformhatch.(2) Turn the lock handle and make sure thatthe hatch is securely closed.(3) Pushthelockhandledown.Rod holdersThis boat is equipped with rod holders on the port and starboard sides of the console.111 Bucket storage compartmentTo drain the bucket storage compartment: (1) Remove the drain plug on the bottom of the bucket storage compartment to drainthe water.1 Rod holder60]]></page><page Index="67" isMAC="true"><![CDATA[Equipment operation 210 FSH Sport1111 Rod holder1 Rod holderLivewellThe livewell for holding live bait and fish is lo- cated on the starboard side of the boat at the stern.To open the livewell:Pull the latch to open the livewell lid.111121 Rod holder1111 Rod holder1 Livewell lid 2 Latch61]]></page><page Index="68" isMAC="true"><![CDATA[Equipment operation111 LivewellTo supply water to the livewell:(1) Push the livewell switch to turn on the livewell pump and supply water.(2) When there is sufficient water in the livewell, push the livewell switch to turn off the livewell pump.(3) If necessary, push the aerator switch to aerate and circulate the water in the livewell. (See page 49.)1 Drain plug(2) Securely install the drain plug in its origi- nal position.T o close the livewell:Close the livewell lid, and then push it to se- curely lock it in place.Battery compartmentDo not carry any flammable substances in the compartment or any heavy or metal items that can damage the battery or cause a short circuit. Sparks or fire could result.The battery compartment is located on the port side of the boat at the stern.To open the battery compartment:Unhook the latch, and then open the battery compartment lid.WARNINGMNLAERATORAUTOLIVEWELL BILGE HORN121 Aerator switch2 Livewell switchTIP:Push the courtesy light switch to turn on the livewell light.To drain water from the livewell:(1) Remove the drain plug on the bottom ofthe livewell to drain the water.62]]></page><page Index="69" isMAC="true"><![CDATA[1 Battery compartment lid 2 LatchEquipment operationWindshieldThe windshield is removable. To remove the windshield:(1) Turn the lock knobs counterclockwiseand remove them.(2) Removethewindshield.12212211 1 Battery compartmentTo close the battery compartment:Close the battery compartment lid, and then hook the latch onto the deck.1 Windshield 2 Lock knobTo install the windshield:(1) Place the windshield in its original posi-tion.(2) Securelyinstallthelockknobsbyturningthem clockwise.63]]></page><page Index="70" isMAC="true"><![CDATA[Equipment operationAnchor light (210 FSH Sport)The anchor light is located at the top of the T- top. (See page 70 for information on the an- chor light on.)To use the anchor light:Pull the lock tab, raise the anchor light, and then move the lock tab to its original position to lock the anchor light in place.Anchor light(210 FSH Deluxe/210 FSH)The boat is equipped with a removable an- chor light.The anchor light is stored in the lockable stor- age compartment. (See page 48 for informa- tion on the anchor light on.)To set up the anchor light:(1) Openthelockablestoragecompartment.(See page 55.)11 Lockable storage compartment(2) Removetheanchorlightfromtheanchorlight holder.11 Lock tabTo store the anchor light:Pull the lock tab, lower the anchor light, and then move the lock tab to its original position to lock the anchor light in place.21641 Anchor light holder2 Anchor light]]></page><page Index="71" isMAC="true"><![CDATA[(3) SlideanchorlightstoppersAandBapart to disconnect them.Equipment operation(5) Open the cap of the anchor light socket, fit the protrusion on the anchor light into the slot in the socket, and then install the light into the socket.213211 Anchor light stopper A2 Anchor light stopper B(4) Extend the anchor light pole, and then screw anchor light stopper A onto the center section of the pole.1 Cap2 Slot3 Protrusion(6) FitanchorlightstopperBintotheanchor light socket.111 Anchor light stopper A1 Anchor light stopper B65]]></page><page Index="72" isMAC="true"><![CDATA[Equipment operationTo store the anchor light:(1) Pull anchor light stopper B upward, re-move the anchor light, and then close thecap of the anchor light socket.(2) Unscrew anchor light stopper A from the center section of the anchor light pole,and then fold the pole.(3) Connect the stoppers by fitting the protru-sion on anchor light stopper A into the slot in anchor light stopper B.Swim platform and ladderStay away from the swim platform area while the engine is running. Exhaust gas- es coming from underneath it contain car- bon monoxide, a colorless, odorless gas which may cause brain damage or death when inhaled. Symptoms include nausea, dizziness, and drowsiness.The swim platform area provides a place to stand or sit while putting on skis or a wake- board, and includes a ladder to make board- ing from the water easier.WARNING211 Anchor light stopper A2 Anchor light stopper B(4) Install the anchor light into the anchor light holder, and then close the lockable storage compartment.1661 Swim platform]]></page><page Index="73" isMAC="true"><![CDATA[To use the ladder:(1) Unhooktheladderstrap.Equipment operation Jet washThe jet wash system must be used only by a passenger who is not operating the boat. While the jet wash system is being used, the boat operator must attach the engine shut-off cord (lanyard) to their PFD and scan constantly for people, objects, and other watercraft.NOTICE● If the jet wash system will not be used for an extended period, turn the shut-off valve to the closed position. Before us- ing the jet wash system, make sure that the shut-off valve is in the open position. If water leaks from the hose fitting or coil hose or if you notice any other problem, turn the shut-off valve to the closed po- sition immediately.● Whilethejetwashsystemisbeingused, scan constantly for people, objects, and other watercraft. Otherwise, the boat could collide with another watercraft, a dock, or other obstacle.● 210 FSH Deluxe/210 FSH: Before using the jet wash system, make sure that the anchor light socket is closed. If the an- chor light socket is not closed and water enters the socket, the socket could mal- function.The hose fitting for the coil hose is located on the deck near the jump seat (starboard).WARNING11 Ladder strap(2) Pull the ladder out completely, and thenlower it.11 LadderTo stow the ladder:(1) Raise the ladder until it is horizontal, andthen push it forward completely.(2) Hook the ladder strap onto the ladder.67]]></page><page Index="74" isMAC="true"><![CDATA[Equipment operation(1) Connectthecoilhosetothehosefitting.(4) Move the jet wash handle lever to dis- charge water.TIP:The water supply will start 5 seconds after the jet wash switch is pushed.110:15 am50% Fuel27 X100 RPM3.0 MPH- Running Mode - 1.5 Hrs12.4V27 X100 RPMJet Wash Mode1 Hose fittingTo use the jet wash:2111 Coil hose2 Hose fitting(2) Starttheengines.(Seepage92.) (3) Pushthejetwashswitch.1 Jet wash handle leverTo stop using the jet wash:(1) Pushthejetwashswitch.(2) Stoptheengines.(Seepage94.)(3) Pushthecollaronthehosefittinginward,and then disconnect the coil hose from the fitting.JET 1 WASH1 Jet wash switch68]]></page><page Index="75" isMAC="true"><![CDATA[Equipment operation(5) To turn off the water supply, turn the shut- off valve 90° counterclockwise.(6) Installtheinspectioncover. (7) Closetherearplatformhatch.11 Hose fittingTo turn the water supply on or off:(1) Stoptheengines.(Seepage94.)(2) Opentherearplatformhatch.(Seepage59.)(3) Removetheinspectioncover.11 Inspection cover(4) To turn on the water supply, turn the shut-off valve 90° clockwise.11 Shut-off valve69]]></page><page Index="76" isMAC="true"><![CDATA[Equipment operationT-top (210 FSH Sport)The bimini top can be installed to use the T-top as a sunshade or rain cover for the leaning post. (See page 70 for bimini top removal and installation procedures.)11 T-topBimini top (210 FSH Sport)The T-top is equipped with a bimini top, which can be used as a sunshade or rain cover for the leaning post.The bimini top can be removed and installed.11 Bimini topTo remove the bimini top:(1) Opentheflaponthestarboardsideofthebimini top.1701 Flap]]></page><page Index="77" isMAC="true"><![CDATA[(2) Loosen the ratchet, and then loosen the strap securing the bimini top.Equipment operationBimini top (210 FSH Deluxe) Setting up the bimini topTo set up the bimini top:(1) Raisethebiminitop.111 Ratchet(3) Slowlypullthebiminitoptowardthebow and remove it.To install the bimini top:When installing the bimini top, simply reverse the removal steps.1 Bimini top(2) Secureeachforwardsupportpoletothe forward support pole mounting bracket using the lock pin.12311 Forward support pole2 Lock pin3 Forward support pole mounting bracket71]]></page><page Index="78" isMAC="true"><![CDATA[Equipment operation(3) Removethestoragecover,unfoldthebi- mini top, and pull it toward the stern.Storing the bimini top in the upright positionNOTICEDo not trailer the boat with the bimini top in the fully extended or upright storage po- sition. Put the bimini top in the fully col- lapsed position to avoid damage.To store the bimini top in the upright position: (1) Removethelockpins,andthenpushthecenter poles down.1121 Storage cover(4) Push each center pole up, and then in-stall the lock pin.121 Center pole2 Lock pin(2) Pullthebiminitoptowardthebow.11 Center pole2 Lock pinNOTICEDo not exceed 72 km/h (45 mph) with the bimini top in the up position.721 Bimini top(3) Installthestoragecover.]]></page><page Index="79" isMAC="true"><![CDATA[Storing the bimini top in the fully collapsed positionTo store the bimini top in the fully collapsed position:(1) Follow the above steps for “Storing the bi-mini top in the upright position”.(2) While supporting the bimini top, remove the lock pins securing the forward sup- port poles to the forward support polemounting brackets.Equipment operationTrailering with the bimini topThe bimini top must be secured to the boat when it is being trailered. When the boat is trailered with a genuine Yamaha boat cover, simply store the bimini top in the fully col- lapsed position and install the boat cover. If a boat cover is not used, wrap an elastic cord around the top and secure the ends to the ski tow hook to restrict movement.Removing the bimini topTo remove the bimini top:(1) Storethebiminitop.See“Storingthebi-mini top in the fully collapsed position”.(2) Removethemainpolemountingpinsse- curing the bimini top to the main polemounting brackets.123111 Forward support pole2 Lock pin3 Forward support pole mounting bracket(3) Lowerthebiminitopontothereardeck.1 Main pole mounting pin(3) Removethebiminitopfromtheboat.Installing the bimini topTo install the bimini top:When installing the bimini top, simply reverse the removal steps, and then make sure that the main pole mounting pins are securely in- stalled.73]]></page><page Index="80" isMAC="true"><![CDATA[Operation and handling requirementsFuelFuel requirementfuel meets minimum octane ratings. E-85 is a fuel blend containing 85% ethanol and there- fore must not be used in this boat. All ethanol blends containing more than 10% ethanol can cause fuel system damage or engine perfor- mance problems.Yamaha does not recommend gasohol con- taining methanol because it can cause fuel system damage and engine performance problems.To fill the fuel tank:(1) Before refueling, turn off the engine. Nev-er refuel while smoking, or while in the vi- cinity of sparks, open flames, or other sources of ignition.(2) Refuel the boat in a well-ventilated area. If the boat is in the water, be sure it is se- curely moored to the fueling dock. All passengers must be out of the boat dur- ing refueling.(3) Press the fuel tank filler cap button, and then open the fuel tank filler cap.WARNING● Gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions.● Gasoline is poisonous and can cause in- jury or death. Handle gasoline with care. Never siphon gasoline by mouth. If you should swallow some gasoline, inhale a lot of gasoline vapor, or get some gaso- line in your eyes, see your doctor imme- diately. If gasoline spills on your skin, wash with soap and water. If gasoline spills on your clothing, change your clothes.NOTICE● Donotuseleadedgasoline.Leadedgas- oline can seriously damage the engine.● Avoidgettingwaterandcontaminantsin the fuel tank. Contaminated fuel can cause poor performance and engine damage. Use only fresh gasoline that has been stored in clean containers.12Recommended fuel:Regular unleaded gasoline with a minimum octane rating of 86 (Pump octane number) = (R + M)/2 90 (Research octane number)GasoholThere are two types of gasohol: gasohol con- taining ethanol and that containing methanol. Gasohol containing ethanol can be used if ethanol content does not exceed 10% and the1 Fuel tank filler cap2 Fuel tank filler cap button(4) Slowlyaddfueltothefueltank.74Fuel tank capacity:197 L (52.0 US gal, 43.3 Imp.gal)]]></page><page Index="81" isMAC="true"><![CDATA[Operation and handling requirements(5) Stop filling when the fuel just becomes visible in the bottom of the filler tube. Do not “top off” the tank, because gasoline could spill out.(6) Wipe up any spilled fuel immediately.(7) Close the fuel tank filler cap by pushing it until it locks in place. Make sure that thefuel tank filler cap is securely closed.Engine Med RX Fuel AdditiveAs the fuel mixture burns in your engine’s combustion chambers, carbon deposits are left behind. Over time, these deposits can re- duce performance and even cause engine damage. Marine engines tend to run at lower operating temperatures than other engines, making them more likely to accumulate these harmful deposits.Engine Med RX, available from your Yamaha Boat Dealer, is formulated to remove existing deposits and, when used continuously, pre- vent new ones from forming, while also help- ing to keep fuel injectors and other fuel system components clean for proper perfor- mance and longer engine life.Engine oil requirement Engine oilNOTICEUse only 4-stroke engine oil. Usage of 2- stroke engine oil could result in severe en- gine damage.Select an oil grade according to the average temperatures in the area where the boat will be used.Recommended engine oil: YAMALUBE 4WRecommended engine oil type:SAE 10W-30, 10W-40, 20W-40, 20W- 50Recommended engine oil grade: API SG, SH, SJ, SLTIP:When the engine is operated at high speeds, some engine oil may be consumed. Be sure to check the engine oil level.Checking the engine oil levelEngine oil is extremely hot immediately af- ter the engines are turned off. Coming in contact with or getting any engine oil on your clothes could result in burns.WARNING75]]></page><page Index="82" isMAC="true"><![CDATA[Operation and handling requirementsNOTICE● Do not run the engine with too much or not enough oil in the oil tank, otherwise the engine could be damaged.● Make sure that debris and water do not enter the oil tank filler hole. Debris and water in the engine oil can cause serious engine damage.TIP:● Whencheckingtheengineoillevelonland, the engine must be running while water is being supplied to the cooling water passag- es. (See “Flushing the cooling system” on page 107 for information on supplying wa- ter.)● When checking the engine oil level on wa- ter, moor the boat so that it will not drift away.To check the engine oil level:(1) With the engine stopped, place the boatin a precisely level position on land orlaunch the boat.(2) Look in all directions, and then start theengine. (See page 92 for information onstarting the engine.)(3) Run the engine at idling speed for 6 min-utes or more. Run the engine an addition- al 5 minutes if the ambient temperature is 20 °C (68 °F) or less.(4) Stoptheengine.(5) Opentheenginehood.(Seepage53.)(6) Loosentheoiltankfillercapandremoveit, and then wipe the attached dipstick clean.1 Oil tank filler cap/Dipstick(7) Screw the oil tank filler cap into the filler hole until it stops. Remove the oil tank fill- er cap again and make sure that the en- gine oil level is between the minimum and maximum level marks.1FL123761 Dipstick2 Maximum level mark3 Minimum level mark(8) Iftheengineoillevelissignificantlyabove the maximum level mark, consult a Yamaha Boat dealer. If the engine oil lev- el is below the minimum level mark, slow- ly add engine oil.(9) Repeatsteps(6)–(8)untiltheengineoilis at the proper level.(10) Securely install the oil tank filler cap and turn it until it stops.]]></page><page Index="83" isMAC="true"><![CDATA[Operation and handling requirements(11)Repeat the checking oil level procedure for the other engine.(12) Close the engine hood.Draining the bilge waterNOTICE● Do not run the engines at full throttle when bilge water remains in the engine compartment. The bilge water can splash into the engines, which can re- sult in severe damage.● Besurealldrainplugsaretightenedbe- fore operating your boat. Otherwise, wa- ter may flood the boat and cause it to submerge.Draining the bilge water on landThis model is equipped with a fuel tank com- partment drain plug and hull drain plug.To drain the bilge water from the various com- partments, see the following sections.Draining the bilge water from the fuel tank compartmentIf there is fuel or a fuel/water mixture in the fuel tank compartment, wipe it up immediately with dry rags. WARNING! This indicates a fuel leak. Do not operate the boat until the source of the fuel leak is found and cor- rected. Gasoline and its vapors are highly flammable and explosive.(1) Opentheenginehood.77]]></page><page Index="84" isMAC="true"><![CDATA[Operation and handling requirements(2) Remove the fuel tank compartment drain plug to drain the water.1Draining the bilge water on waterThis model is equipped with a self-draining deck and bilge pump to drain the bilge water on water.Self-draining deckMost water that enters the deck area drains automatically out the stern through the large drain holes in the deck.A one-way check valve in each drain prevents water from traveling back to the deck while the boat is moored or moving in reverse.Bilge pumpYour boat is equipped with a drainage system that channels water that enters the boat from the storage compartments to the bilge under the engine compartment. When the bilge pump switch and the battery switch are turned on, the bilge pump will detect when there is excessive water in the bilge and will automat- ically drain most of it through the bilge pump outlet. For normal operation, turn the bilge pump switch on during boat use and turn it off when leaving the boat. NOTICE: If the boat is to be left in the water after use, leave the bilge pump switch and the battery switch in the on position. The pump will activate if needed to drain any water accumulating in the bilge.1 Fuel tank compartment drain plug(3) If the boat was operated in salt water, wash down the compartment with fresh water.(4) Securelyinstallthedrainpluginitsorigi- nal position.(5) Closetheenginehood.Draining the bilge water from the hullRemove the hull drain plug at the stern to drain the water. Check the condition of the O-ring on the hull drain plug, and then secure- ly install the drain plug.1 Hull drain plug781MNLAERATORAUTOLIVEWELLBILGE HORN11 Bilge pump switch]]></page><page Index="85" isMAC="true"><![CDATA[Operation and handling requirements11 Bilge pump outlet79]]></page><page Index="86" isMAC="true"><![CDATA[First-time operation Engine break-inNOTICEFailure to perform the engine break-in could result in reduced engine life or even severe engine damage.The engine break-in period is essential to al- low the various components of the engines to wear and polish themselves to the correct op- erating clearances. This ensures proper per- formance and promotes longer component life.(1) Checktheengineoillevel.(Seepage75 for information on checking the engine oil level.)(2) Launch the boat and start the engines. (See page 92 for information on starting the engines.)(3) For the first 5 minutes, operate with the engines at idling speed.(4) Forthenext30minutes,operatewiththe engines speed below 5000 r/min.(5) Forthenext1hour,operatewiththeen- gines speed below 6500 r/min.After the engine break-in is complete, the boat can be operated normally.80]]></page><page Index="87" isMAC="true"><![CDATA[Pre-operation checksWARNINGFailure to inspect or maintain the boat properly increases the possibility of an accident or damage to the boat. Do not operate the boat if you find any problem.If a problem cannot be corrected by the procedures provided in this manual, have the boat inspected by a Yamaha Boat Dealer.Pre-operation checklistBefore operating this boat, perform the checks in the following checklist. Always follow the inspec- tion and maintenance procedures and schedules described in this owner’s/operator’s manual. Pre-operation checks should be made each time the boat is used. These checks can be com- pleted in a short time. It is worth the time spent to ensure safety and reliability.ITEMCHECKPAGEPRE-LAUNCH CHECKSSteering systemCheck for proper steering operation.83Remote control leversCheck for proper throttle operation. Check for proper shift operation.83Fire extinguisherCheck readiness of the extinguisher.84HullCheck hull for damage and cracks before launching.—Access port capCheck for proper installation.85Jet intakesCheck that no debris is in the intake before launching.86Fuel systemCheck fuel system for leaks.86Engine oil levelCheck engine oil level; add as necessary.75BatteryCheck battery condition, mounting, and connection.87Bilge waterCheck the engine compartment and fuel tank compart- ment for bilge water.87Drain plugsCheck the drain plugs for damage and foreign material and check that they are securely installed.87Engine compartment and blowersOpen the engine hood and check to be sure no gasoline, gasoline vapors, or loose electrical connections are pres- ent. Operate the blowers for at least 4 minutes.88Engine hoodCheck that the hood latches are secure.53Lights and hornCheck lights to be sure they operate. Push the horn switch to be sure it operates.88, 89Bimini top (210 FSH Sport/ 210 FSH Deluxe)Check that the top is secure.70, 71Engine shut-off cord (lan- yard)Check the engine shut-off cord (lanyard) for damage.89T-top (210 FSH Sport)Check that the T-top screws and nuts are secured.7081]]></page><page Index="88" isMAC="true"><![CDATA[Pre-operation checksITEMCHECKPAGEPOST-LAUNCH CHECKSSwitchesCheck operation of the main switches and engine shut- off switch.90Cooling water pilot outletsCheck that water comes out while the engines are run- ning.90Fuel levelCheck fuel level; add as necessary.90The steering and shifting pre-operation checks will require two persons: one person to operate the controls and one person to observe the proper operation at the stern.82]]></page><page Index="89" isMAC="true"><![CDATA[Pre-operation checksPre-operation check points Pre-launch checksPerform the pre-launch checks in the pre-op- eration checklist while the boat is on land.Steering system checksMake sure the steering wheel is not loose. There should not be any free play, either in- and-out or in rotation. Turn the steering wheel fully to the right and left to make sure opera- tion is smooth and unrestricted throughout the whole range.1 Jet thrust nozzle 2 Articulating keelRemote control lever checksDo not touch the shift gates while the re- mote control levers are being operated, otherwise, you could be pinched.Operate the remote control levers several times to make sure that operation is smooth throughout the whole range.121WARNINGMake sure both the jet thrust nozzles change directions as the steering wheel is turned. The jet thrust nozzles should point to starboard (right) when the wheel is turned to the right. The jet thrust nozzles should point to port (left) when the wheel is turned to the left. There should not be free play between the steering wheel and the jet thrust nozzles. In addition, check that the direction of the articulating keel changes according to the movement of the jet thrust nozzles.1 Neutral position 2 TDE position3 Forward position 4 Reverse position 5 Shift6 Fully closed 7 Throttle8 Fully openF2 N1 R 55347667 8883]]></page><page Index="90" isMAC="true"><![CDATA[Pre-operation checksCheck that the shift gates are slightly above the shift gate neutral position when the re- mote control levers are in the forward posi- tion, and that the shift gates are in the fully open position when the remote control levers are moved farther forward.Fully open positionthe craft carry a USCG-approved fire extin- guisher whenever the boat is operated. Make sure at least one fire extinguisher is aboard and full; two fire extinguishers are rec- ommended. See the instructions supplied by the extinguisher manufacturer to determine the indication of the condition.A fire extinguisher is not standard equipment with this boat. If you do not have a fire extin- guisher, contact your local Yamaha Boat Dealer or fire extinguisher dealer for one meeting the proper specifications.Storing the fire extinguisherOne fire extinguisher is to be mounted in the lockable storage compartment. The fire extin- guisher recommended for this location is a chemical-type extinguisher with a capacity of two pounds or more.111 Shift gateCheck that the shift gates are in the fully closed position when the remote control le- vers are in the reverse position.Fully closed position11 Shift gateFire extinguisher checkAs an inboard boat less than 26 feet in length, your boat must be fitted with one B-1 type fire extinguisher when navigating waters con- trolled by the U.S. Coast Guard. In addition, most state and local boating laws require thatIf you choose to have two fire extinguishers, the other fire extinguisher is to be mounted in the battery compartment. There is a location label outside the compartment. This fire extin- guisher located near the engine compartment should be a “clean agent” type designed to displace oxygen, with an inert gas, such as CO2, or FE-36TM, and have a capacity of five pounds or more.84]]></page><page Index="91" isMAC="true"><![CDATA[Operating the fire extinguisherA chemical-type fire extinguisher may not help when sprayed into the engine compart- ment through the FIRE-PORTTM because that type needs to be aimed directly at the base of the flames to be effective. See below for FIRE-PORTTM information.Pre-operation checksA FIRE-PORTTM is mounted below the lean- ing post. Use this port to spray the contents of a fire extinguisher into the engine compart- ment if a fire breaks out in the engine area. WARNING! If there is a fire in the engine compartment, opening the hatch will add more oxygen to the fire, increasing the risk of a larger fire or an explosion.If you see smoke or otherwise suspect a fire, you can look through the transparent flaps of the FIRE-PORTTM to look for signs of flames. If there is a fire, push the nozzle of the fire ex- tinguisher through the FIRE-PORTTM and fol- low the manufacturer’s instructions to empty the contents of the fire extinguisher into the engine compartment.A “clean agent” type fire extinguisher is rec- ommended; a chemical-type fire extinguisher may not be adequate in this application.Access port cap checkMake sure that the access port caps are se- curely installed.To check the access port caps:(1) Opentherearplatformhatch.(Seepage59 for information on the rear platformhatch.)(2) Makesurethattheaccessportcapsaresecurely installed. If they are removed or are not locked, securely install them. (See page 122 for information on the ac- cess port caps.)11 FIRE-PORTTM85]]></page><page Index="92" isMAC="true"><![CDATA[Pre-operation checks1 Access port cap(3) Closetherearplatformhatch.Jet intake checksCarefully check the jet intakes under the boat for weeds, debris, or anything else that might restrict the intake of water. If the intakes are clogged, cavitation could occur, reducing jet thrust, and possibly damaging jet pump parts.11 Jet intakeIn some cases, the engines may overheat be- cause of a lack of cooling water, and damage could result. If the jet intakes are clogged, clean them. (See page 122 for information on the jet intakes.) WARNING! Rotating parts could cause severe injury or death. Before attempting to remove weeds or debris from the jet intakes or impeller areas; shut off the engines, remove the main switch861key, and then remove the engine shut-offcord (lanyard) from the engine shut-offswitch.Fuel system checksCheck the fuel filler hoses and joints in the en- gine compartment for damage, looseness, and signs of leaking. At least annually, or if a problem is suspected, check the fuel tank and fuel filler hoses and clamps. Have a Yamaha Boat Dealer check the fuel tank and fuel filler hoses and clamps.Engine oil level checkMake sure that the engine oil level is between the minimum level mark and maximum level mark on the dipstick. (See page 75 for infor- mation on checking the engine oil level.)11 Oil tank filler cap/Dipstick]]></page><page Index="93" isMAC="true"><![CDATA[FL1231 Dipstick2 Maximum level mark3 Minimum level markBattery checkMake sure that the battery terminals are not damaged and that the battery leads are con- nected properly. WARNING! The battery must always be fully charged and in good condition. Loss of battery power may leave you stranded. Never operate the boat if the battery does not have sufficient power to start the engines or if it shows any other signs of decreased power.Pre-operation checksthe engine compartment and the fuel tank compartment, drain it. (See page 77 for infor- mation on draining the bilge water.)Drain plug checkLoosen the drain plugs and remove them, and then make sure that the plugs and the O-rings on the hull drain plugs are not damaged and that there is no foreign material on the threads or the O-rings on the hull drain plugs. NOTICE: Before installing the drain plugs, clean the drain plug threads and the O-rings on the hull drain plugs to remove any foreign materials, such as dirt or sand. Otherwise, the drain plugs could be dam- aged, allowing water to enter the engine compartment or the fuel tank compart- ment. Make sure that the drain plugs are tightened securely before launching the boat. Otherwise, water may flood the boat and cause it to submerge.Securely install the drain plugs by tightening them until they stop.12111 Negative (–) battery terminal: Black lead2 Positive (+) battery terminal: Red leadBilge water checkMake sure that no bilge water has collected in the engine compartment and the fuel tank compartment. If bilge water has collected in1 Hull drain plug87]]></page><page Index="94" isMAC="true"><![CDATA[Pre-operation checks1 Fuel tank compartment drain plugBlower switch checkWARNING1 BlowerPush the blower switch to operate the blower and ventilate the engine compartment for at least 4 minutes.Navigation and anchor lights switch checkPush the navigation and anchor lights switch and check that the bow light and anchor light come on.(1) 210FSHDeluxe/210FSH:Installthean- chor light. (See page 64 for information on the anchor light.)(2) Pushtheuppersideofthenavigationand anchor lights switch and check that the bow light and anchor light come on.Gasoline vapors can explode. Before starting the engine, check the engine com- partment for gasoline, gasoline vapors, and loose electrical connections, and then operate the blower for at least 4 minutes. Do not start the engine or operate the blower if you can smell gasoline vapors in the engine compartment or if there are any loose electrical connections.Contact a Yamaha Boat Dealer if there is a problem you cannot locate or correct.Make sure that the blower operates properly when the blower switch is pushed.11 Blower switchBLOWER88111NAV/ANC CTSYLIGHTS11 Navigation and anchor lights switchACC ACC]]></page><page Index="95" isMAC="true"><![CDATA[1Pre-operation checks(4) Put the navigation and anchor lights switch in the middle position and check that the bow light and anchor light are off.(5) 210 FSH Deluxe/210 FSH: Remove the anchor light.Horn switch checkPush the horn switch and check that the horn sounds.MNLAERATORAUTOLIVEWELL BILGE HORN11 Bow light210 FSH Deluxe/210 FSH11 Anchor light 210 FSH Sport1 Horn switchEngine shut-off cord (lanyard) checkMake sure that the engine shut-off cord (lan- yard) is not damaged. If the cord is damaged, replace it. WARNING! Never try to repair the engine shut-off cord (lanyard) or tie it together. The engine shut-off cord (lan- yard) may not pull free when the operator falls off, allowing the boat to continue to run and cause an accident.11 Anchor light(3) Pushthelowersideofthenavigationand anchor lights switch and check that only the anchor light comes on.89]]></page><page Index="96" isMAC="true"><![CDATA[Pre-operation checksPost-launch checksPerform the post-launch checks in the pre-op- eration checklist while the boat is in the water and the engines are running.Engine shut-off switch checkCheck the engine shut-off switch for proper operation.(1) Starttheengines.(Seepage92forinfor-mation on starting the engines.)(2) Pulltheengineshut-offcord(lanyard)to remove the clip from the engine shut-off switch to make sure that the engines stopimmediately.(3) Make sure that the engines cannot bestarted with the clip removed from the en- gine shut-off switch.TIP:It may take up to 20 seconds for water to reach the pilot outlets when first launching the boat. The amount and force of the exiting wa- ter will vary with engine speed.NOTICEA continuous flow of water from the pilot outlets shows that water is flowing through the engine cooling water passag- es. If water is not flowing out of the pilot outlets during operation, do not continue to run the engines. Overheating and seri- ous damage could occur. (See “Engine overheat warning system” on page 43 for more information.)Fuel level checkCheck the amount of fuel remaining in the fuel tank using the fuel level bar graph on the multi-function display.121 Engine shut-off switch 2 ClipCooling water pilot outlet checkCheck that water comes out from the pilot out- lets while the engines are running in the wa- ter. If water is not circulating, something may be clogging the intake grates. Refer to “Jet pump clean-out procedure” on page 122.90]]></page><page Index="97" isMAC="true"><![CDATA[Pre-operation checks110:15 am77˚F50% FuelPORT 1.5 HrsWater12.4 VSTBD 1.6 Hrs- Float Mode - STBD 1.6 Hrs1 Fuel level bar graphAdd fuel if necessary. (See page 74 for infor- mation on filling the fuel tank.)91]]></page><page Index="98" isMAC="true"><![CDATA[OperationDriving your boat Getting to know your boatcles. Do not operate where people are swim-ming. Operating your boat requires skills acquiredthrough practice over a period of time. Takethe time to learn the basic techniques well be-fore attempting more difficult maneuvers. Boating with your new boat can be a very en- joyable activity, providing you with hours of pleasure. But it is essential to familiarize your- self with the operation of the boat to achieve the skill necessary to enjoy boating safely. Before operating this boat, read this own- er’s/operator’s manual, the Operation Instruc- tion card, and all labels on the boat. Pay particular attention to the safety information beginning on page 10. Also, watch the Basic Orientation Video provided with your boat. These materials should give you an under- standing of the boat and its operation. This boat is designed to carry one operator and up to 9 passengers.Always attach the engine shut-off cord (lan- yard) to your PFD before operating.You and all other passengers must always wear a USCG-approved PFD when riding in the boat. You should consider wearing water shoes, eye protection, and other protective apparel. Water sports increase your risk of in- jury from contact with your boat, other ves- sels, docks, rocks, or coral.Grip the steering wheel firmly and keep both feet on the deck when driving the boat.Starting the engineSevere injury or death may result if you ig- nore any of the following:● Before operating your boat, become fa-miliar with all controls. Consult a Yamaha Boat Dealer about any control or function you do not fully understand. Failure to understand how the controls work could cause an accident or prevent you from avoiding an accident.● Gasoline vapors can explode. Before starting the engines, check the engine compartment for gasoline, gasoline va- pors, and loose electrical connections, and then operate the blowers for at least 4 minutes. Do not start the engines or operate the blowers if you can smellMaximum load:Total weight of cargo, operator, and passengers:1021 kg (2250 lb)Total weight of operator and passen- gers:844 kg (1860 lb)WARNINGLearning to operate your boatBefore boating, always perform the pre-oper- ation checks listed on page 81. The short time spent checking the boat will reward you with added safety and reliability.Know and follow U.S. Coast Guard, state, and local laws when operating your boat.Select a wide area to learn in, where visibility is good and other boat traffic is light. Keep the proper distance from other boats and vehi-92]]></page><page Index="99" isMAC="true"><![CDATA[gasoline vapors in the engine compart- ment or if there are any loose electrical connections. Contact a Yamaha Boat Dealer if there is a problem you cannot locate or correct.● Attachtheengineshut-offcord(lanyard) to your PFD before operating. Failure to attach the cord could result in a runaway boat if the operator is ejected.● Do not apply throttle when anyone is at the rear of the boat. Turn the engines off or keep it at idle. Water and debris exit- ing the jet thrust nozzle can cause se- vere injury.(1) Always make sure the boat is launched and used in waters that are free from weeds and debris, and at least 90 cm (3 ft) deep from the bottom of the boat. WARNING! Never operate in water that is less than 90 cm (3 ft) deep from the bottom of the boat. You increase your chance of hitting an underwater ob- stacle. You could be injured. Pebbles or sand can also be sucked into the jet intakes, damaging the impellers.NOTICEThere is a hull drain plug at the bottom of the stern. Check the O-ring on the hull drain plug and make sure that the plug is tightened securely before launching theOperationboat. Otherwise, water may flood the boat and cause it to submerge.11 Hull drain plug(2) Turn the battery switch to the ON posi- tion.(3) Push the blower switch to operate the blowers and ventilate the engine com- partment for at least 4 minutes.1BLOWER90 cm (3 ft)1 Blower switch(4) Attach the engine shut-off cord (lanyard) to your PFD. Install the clip onto the en- gine shut-off switch by pushing the clip groove over the nut beneath the knob. Be sure the cord is not wrapped around the steering wheel or tangled in the controls. WARNING! Check that the engine shut-off cord (lanyard) is attached cor- rectly. If the engine shut-off cord (lan- yard) is not attached correctly, it may93]]></page><page Index="100" isMAC="true"><![CDATA[Operationnot pull free when the operator falls off, allowing the boat to continue to run and cause an accident.BLOWER1231 Engine shut-off switch2 Clip3 Engine shut-off cord (lanyard)TIP:The engines will not start when the clip is re- moved from the engine shut-off switch. The starter motors will turn over without the cord attached.(5) Put the remote control levers in the neu- tral position. The starter motors will not operate unless the remote control levers are in neutral.(6) Turn the main switch keys to the start po- sition and release it when the engines start. If the engines do not start after 5 seconds of cranking, release the keys. Wait at least 15 seconds before trying to start the engines again.NOTICE● Never turn the main switch keys to the start position while the engines are run- ning. The starter mechanism could be damaged.● Ifthestartermotorsareengagedcontin- uously for more than 5 seconds, the bat- tery will become quickly discharged and it will be impossible to start the engines. The starter motors may also be dam- aged if they are engaged continuously for more than 5 seconds.On this boat, the engines are connected di- rectly to the drive units. Starting either engine generates some thrust immediately. Only enough throttle should be applied to keep the engine at a fast enough idle to stay running.Stopping the enginesOnce the engines has stopped, you have NO STEERING CONTROL over the boat. You could collide with another boat, a dock, or other obstacle.Stopping the engines immediately after oper- ating at high engine speeds is not recom- mended. Let the engines cool off at idle or low speed for a few minutes first.WARNING94]]></page><page Index="101" isMAC="true"><![CDATA[To stop the engines:(1) Return the remote control levers to theneutral position.(2) Turn the main switch key to the off posi-tion.(2)Operationor forward position will start to move the stern of the boat away from the dock. When the stern is out a few feet, release the bow mooring, and then turn the steer- ing wheel to the center position or away from the dock. Move the remote control levers into the reverse position and move away from the dock.BLOWERWARNINGTIP:The engines can also be stopped by pulling the engine shut-off cord (lanyard).(3) Remove the main switch keys and theengine shut-off cord (lanyard) if the boat will be left unattended.Leaving a dockBecause boats steer from the stern, the stern first moves in the direction opposite your de- sired turn. It is especially important to under- stand this characteristic when leaving a dock. If you move the remote control levers to the forward position and simply turn the steering wheel to steer the bow away from the dock, as you would when driving a car out of a parking space, you will drive the stern of the boat into the dock.The following steps are basic maneuvering techniques which can be used in most circum- stances:(1) With the engines idling and the bow stillmoored to the dock, turn the steering wheel toward the dock. Moving the re- mote control levers into the TDE positionTurning the boat● Do not pull the remote control levers back to idle when trying to steer away from objects — you need throttle to steer.● Be sure passengers are holding on be- fore making turns. An unprepared pas- senger could lose balance and fall.Steering control depends on the combination of steering wheel position and the amount of throttle.Water sucked in through the intake grate is pressurized by the impeller in the jet pumps. As the pressurized water is expelled from the pumps through the jet thrust nozzles, it cre- ates thrust to move and steer the boat. The higher the engine speed, the more thrust is produced.The amount of jet thrust, in addition to the po- sition of the steering wheel, determines how sharply you turn.A. More throttle produces high thrust, so theboat will turn more sharply.95]]></page><page Index="102" isMAC="true"><![CDATA[OperationACB. Less throttle produces low thrust, so the boat will turn more gradually.D. If the boat is moving and the remote con- trol levers are in neutral position, or if there is no thrust because the engines are stopped, the boat will go straight even though the steering wheel is turned. You need throttle to steer.BDC. Pulling the remote control levers back to idle or neutral position produces only minimum thrust. If you are traveling at speeds above trolling, you will have rap- idly decreasing ability to steer without throttle. You may still have some turning ability immediately after pulling the re- mote control levers back to idle, but when the engines slows down, the boat will no longer respond to steering wheel input until you apply throttle again or you reach a trolling speed.At trolling speed, the boat can be turned gradually by steering wheel position alone using just the amount of thrust available at engine idle.Turning left96]]></page><page Index="103" isMAC="true"><![CDATA[Turning rightStopping the boatOperationWARNINGBoating with passengersWhen passengers are on board, make sure they are seated and holding onto the handgrips before you start to accelerate. An unprepared passenger could lose bal- ance and fall.Your boat is designed for one operator and up to 9 passengers only. Never have more than 10 people in the boat. Passengers must sit in one of the seats and hold onto the handgrips. Passengers should sit so the weight in the boat is balanced from side-to-side and bow- to-stern as much as possible. If the passenger seat in front of the helm is used, be sure the operator’s view ahead is not obstructed.● Allowadequatestoppingdistance.● Takeearlyactiontoavoidcollisions.Re-member, boats do not have brakes.● Operate defensively at safe speeds and keep a safe distance away from people, objects, and other boats to give you timeto stop.● Donotshuttheengineoffwhenslowingdown in case you need engine power to steer away from a boat or other obstacle that comes into your path.● You will lose steering control if you completely pull the throttle back to idle. You need throttle to steer.● Do not use the reverse function to slow down or stop the boat from planing speed as it could cause you to lose con- trol, be ejected, or impact the steering wheel or other parts of the boat. This could increase the risk of serious injury.The boat is not equipped with a separate braking system. It is stopped by water resis- tance after the remote control levers are moved back to idle. From full speed, the boat stops in approximately 107 m (350 ft) after the remote control levers are moved back to idle. The stopping distance varies depending on gross weight, water surface conditions, and wind direction. The stated straight-line stop- ping distance should be used for a reference. The boat slows down as soon as the remote control levers are returned to idle but will coast for a distance before fully stopping. If you are not sure you can stop in time before hitting an obstacle, apply throttle and turn in another direction.WARNINGMaximum load:Total weight of cargo, operator, and passengers:1021 kg (2250 lb)Total weight of operator and passen- gers:844 kg (1860 lb)97]]></page><page Index="104" isMAC="true"><![CDATA[Operation115 m (377 ft)Boarding from the waterTo avoid severe injury or death, do not board from the rear, use swim platform, or swim behind boat if engines are running.● Severe internal injuries can occur if wa-ter is forced into body cavities as a re-sult of being near the jet thrust nozzles.● Exhaustgasescomingfromunderneath the swim platform contain carbon mon- oxide, a colorless, odorless gas which may cause brain damage or death when inhaled. Symptoms include nausea, diz-ziness, and drowsiness.(1) Be sure the engines are off, and then move to the stern of the boat.(2) Pullouttheladderandclimbupontothe swim platform. (See page 66 for informa- tion on ladder.)(3) Returntheladdertothestowedposition, and then sit in one of the seats provided.Boarding from a dock or landing jetty(1) Boardtheboatfromtheside.Oneperson should board at a time by stepping into the boat. Never jump in. Avoid stepping on slick gelcoat surfaces on the boat’s gunwales, especially if wet.(2) Sit in one of the seats provided and put both feet on the deck.Docking(1) Make sure no obstructions, boats, or swimmers are close to the boat. Come to a stop before you reach the dock.(2) Notice how wind and water currents are affecting boat movement as you attach your mooring lines and fenders.(3) Approach the dock at idle speed. Use re- verse as necessary during slow-speed maneuvering to help control speed and direction. Position the boat according to wind and water conditions. WARNING! Do not use your hand, arm, or other parts of your body to try to keep the boat from hitting the dock. You could be injured if the boat pushes against the dock.Wind or current pushing boat away from dock:Slowly approach the dock at about a 45° an- gle. Secure the bow to the dock, and then use engine thrust or a boat hook to gently move the stern to the dock.WARNING98]]></page><page Index="105" isMAC="true"><![CDATA[Wind or currentWind or current pushing boat toward dock:Slowly maneuver to a shallow angle and allow the boat to move toward the dock.Operation● Do not beach the boat on rocky beach- es. The hull gelcoat and exposed pump housings can be damaged.● Payattentiontoshiftsintides.Beaching at high tide may make it impossible to re-launch the boat if the tide recedes.(1) Make sure no obstructions, boats, or swimmers are near the beach.(2) Approach the beach slowly and stop the engines when the water is about 90 cm (3 ft) deep from the bottom of the boat. Remember: turning is impossible with the engines stopped.(3) Getoutoftheboatandpullthebowupon the beach.(4) When leaving the beach, push the boat out into water that is at least 90 cm (3 ft) deep from the bottom of the boat before starting the engines.AnchoringAlways anchor from the bow. Anchoring from the stern will make the boat un- steady. A strong current can pull a stern- anchored boat underwater.Select an anchor appropriate for your boat and water conditions. A “Danforth” (or fluke) type anchor is suitable for most applications; your Yamaha Boat Dealer can help you choose an anchor.(1) Makesuretheanchorlineissecurelytied to the anchor and to the bow eye or a bow cleat.(2) Movetheboattothespotwhereyouwant to lower the anchor, heading the boat into the wind or current. Stop the boat, and then lower the anchor until it hits bottom.Wind or currentWARNINGNo wind or current:Approach the dock at a shallow angle. Secure the bow to the dock, and then use engine thrust or a boat hook to gently move the stern to the dock.BeachingNOTICE● Smallpebbles,sand,seaweed,andoth- er debris can be sucked into the jet in- takes and impair or damage the impellers. Always stop the engines be- fore beaching the boat. Be sure the boat is in water 90 cm (3 ft) deep from the bot- tom of the boat before starting the en- gines again.99]]></page><page Index="106" isMAC="true"><![CDATA[Operation(3) Whilekeepingtensionontheline,slowly back up the boat until you have let out line that is 4–6 times the depth of the water. For example, if you are anchoring in 10 feet of water, let out 40–60 feet of line. Secure the line.(4) Pull on the line to be sure the anchor is holding. Also, periodically check your boat’s position against the shoreline to make sure it is not drifting and dragging the anchor. Reset if necessary.(5) To pull in (“weigh”) the anchor, start the engines and move forward, keeping ten- sion on the line as you pull it in. When the anchor line is straight up and down, pull hard to lift the anchor from the bottom material.(6) If the anchor is stuck on the bottom, try this: Let out a few feet of anchor line and secure the line to the boat, again. Slowly maneuver the boat around the anchor until the anchor pulls loose. Keep the line taut during this procedure.Crossing wakes and swellsYou will not always have flat, smooth water. There will be swells and wakes from other boats, etc.The best way to cross wakes and swells is with the least jolt to you and the boat. Small swells are not as difficult to cross as larger swells or wakes. Crossing a sharp wake gives more of a jolt than a broad swell.To cross a wake or swell, change your speed and choose the angle at which you cross the wake or swell. Usually, a slower speed and “quartering” the wake (crossing at an angle) will reduce the jolt.Two other things you may notice. The first is that crossing a group of wakes or swells is not as easy or smooth as crossing just one wake. The second is that when you quarter the wake or swell, the boat will try to steer away from the wake or swell. When crossing at a 45° an- gle, you may not notice this, but at a smaller angle, say 10°, it can be very strong. Be pre- pared to steer and balance as necessary.Sharp wakesBroad swellWake90˚45˚10˚100]]></page><page Index="107" isMAC="true"><![CDATA[Post-operation checksThese post-operation procedures are devel- oped to help preserve the long-term appear- ance and reliability of your boat. Perform these procedures as soon as possible after the boat is loaded back on the trailer after the day’s use.Some owners prefer to moor their boat sea- sonally, rather than keeping it on the trailer between uses. Extended mooring is not recommended. Proper flushing of the cool- ing system is not possible with the boat in the water. In addition, conditions such as stray electrical voltage in the water, marine organ- isms, and saltwater corrosion can adversely affect the life of many boat components. NOTICE: Leaving the boat in the water for extended periods will accelerate the rate of normal deterioration of the jet pump components, sacrificial anodes, hull finish and other components.If you do decide to moor your boat, be sure to remove it from the water periodically to clean the hull and jet pump area. The frequency of maintenance required will depend upon whether the water is salt water or fresh water and other local water conditions.(1) After putting the boat on the trailer, flush the cooling system to prevent the cooling system from clogging up with salt, sand, or dirt. (See page 107 for the cooling sys- tem flushing procedure.)(2) Drain residual water from the exhaust system by starting the engine, and then alternately pushing the remote control le- ver up to half throttle and back to idle for 10 to 15 seconds. NOTICE: Do not run the engine over 4000 r/min on land. Al- so, do not run the engine for more than 15 seconds without supplyingOperationwater, otherwise, the engine couldoverheat and/or seize.(3) Stoptheengine.(4) Wash down the hull, helm, and jet driveunit with fresh water.(5) Opentherearplatformhatch.(Seepage59 for rear platform hatch opening andclosing procedures.)(6) Remove the access port cap to let anywater drain that has pooled on it. (See page 122 for access port cap removal and installation procedures.) If the boat will be stored on the trailer nearby, leave the cap out until you prepare to launch the boat again. If the boat will be trans- ported on the trailer any distance, tempo- rarily reinstall the cap and close the hatch until you get home. Open the hatch again when you arrive and remove the cap as before. Leave the cap loose until you plan to transport the boat on the trailer again. NOTICE: Leaving the access port cap out when you are not using or trans- porting the boat helps keep it from be- coming stuck in the access port.(7) Remove the hull drain plug and the fuel tank compartment drain plug. (See page 77.)(8) Rinse the engine compartment with a small amount of fresh water. Be careful not to get water on the air filter area or electrical components. Allow any water in the bilge to drain out. After the water has drained, wipe the engine compartment and bilge with dry rags.(9) Reinstallalldrainplugs.NOTICE:Tight- en the hull drain plug securely before launching the boat. Otherwise, water may flood the boat and cause it to sub- merge. Clean any foreign material, such as dirt or sand, from the threads101]]></page><page Index="108" isMAC="true"><![CDATA[Operationand the O-ring on the hull drain plugbefore installing the drain plugs.(10)Spray a rust inhibitor, such as Yamaha Silicone Protectant and Lubricant, on me- tallic parts to minimize corrosion.(11) Use the included boat cover, or store the boat in a building or under a canopy or carport in order to prevent rain from fall- ing onto the boat. Because all of the wa- ter will not be drained from the deck automatically, take sufficient measures to prevent rainwater from entering the boat. NOTICE: Make sure that the turnbuck- les on the boat cover do not contact the boat directly when using the cov- er. Otherwise, the boat could be dam- aged.(12)Turn the battery switch in the battery compartment to the OFF position. (See page 30 for more information.)102]]></page><page Index="109" isMAC="true"><![CDATA[Trailering the boatAvoid accident and injury from improper trailering:● The trailer must be matched for theboat’s weight and hull.● The towing vehicle must have the capac-ity of pulling the load. Pulling a load that exceeds the towing capacity may cause loss of control.● Be sure the boat is secured to the trailer and the trailer is properly hitched to the towing vehicle before towing.● Read the manuals supplied with the trailer by the manufacturer.A trailer is provided as standard equipment with your boat. If you need to obtain another trailer, choose one that is manufactured to carry a boat of the size and weight of your boat. Check the certification label on the left forward side of the trailer. This label is re- quired to show the Gross Vehicle Weight Rat- ing (GVWR), which is the load carrying capacity of the trailer plus the trailer’s weight. Be sure that the total weight of your boat, any cargo, and the trailer weight itself does not ex- ceed the GVWR.HitchThe trailer hitch ball must match the size of the socket on the trailer hitch coupler. Hitches are divided into classes that specify the Gross Trailer Weight (GTW) and the maximum tongue weight. Always use a hitch rated for the same or higher class. Use a bolted-on or welded-on hitch; clamp-on bumper hitches are not recommended. Be sure the trailer hitch’s release handle is latched with the lock pin installed before towing.TraileringUse safety chains between the towing vehicle and the trailer so the trailer will not detach completely from the towing vehicle if it acci- dentally comes loose from the hitch ball. Crisscross the chains under the trailer tongue so the tongue will not hit the road surface if it falls loose. Rig the chains as tightly as possi- ble while allowing just enough slack to permit tight turns.Be sure the tongue weight (vertical weight on the hitch point) is correct. Generally, 5% to 10% of the combined weight of the boat and trailer should be on the tongue. Too much or too little weight can cause difficult steering or trailer swaying.Trailering checklist● Checkyourstatelawstobesureyourtrailer meets all regulations, such as proper li- censing, brake, axle load, and safety chain requirements.● Check the trailer for any loose fasteners or damaged parts.● Checkthetiresforproperinflation.● Check the wheel bearings and wheel lugnuts before each trip.● Checkthetail,brake,andturnsignallightsfor proper operation.WARNING103]]></page><page Index="110" isMAC="true"><![CDATA[Trailering●Secure the bow of the boat to the trailer with the winch line and also with the chain. Se- cure the stern eyes to the trailer with tie- downs.● While traveling, check the wheel hubs on the trailer whenever you park. If a hub feels abnormally hot, have the bearing inspected before continuing your trip. On longer trips, it is a good idea to carry a set of spare wheel bearings, seals, and races.● When making a turn, do not cut corners. The trailer has a smaller turning circle, so it turns more sharply around the corner than the towing vehicle.Backing your trailerIt takes practice to back a trailer successfully. If you are not familiar backing up with a trailer, practice first in an open area away from ob- stacles.11Bow eye111Stern eyeTIP:During transport, use a boat cover to prevent any items from blowing out of the boat, or make sure to store any items inside the stor- age compartments and securely close the compartments.● Be sure the access port cap is properly in- stalled (see page 122 for more information) and the rear platform hatch is closed se- curely.● Be sure any cargo that must be carried in the boat as well as the all hatches are se- cured.Keep the following points in mind when backing up● Back slowly. Make steering adjustments insmall steps.● Turn the towing vehicle’s wheels oppositethe direction you want the trailer to go.● Afterthetrailerbeginsmoving,turnthetow-ing vehicle to follow it.● Have a second person stand by to help di-rect you with hand signals.LaunchingAs a courtesy to other boaters, prepare your boat for launching before using the ramp.104]]></page><page Index="111" isMAC="true"><![CDATA[such as ramp angle, prevailing wind, waves, and water currents. If possible, watch a cou- ple of boaters launch their boats first to notice any problems. While every boater develops a preferred launch procedure, here is a recom- mended general procedure:(1) Disconnect the trailer lights from the tow- ing vehicle.(2) Back the trailer down the ramp as close to 90° to the shoreline as you can. If pos- sible, have a second person act as an ob- server while standing to the side of the trailer. Stop when the tops of the trailer’s fenders are about 3 inches above the wa- terline.(3) With the boat moving at the slowest idle speed, guide the boat onto the support rails. Use throttle only if necessary for steering ability. WARNING! Using too much throttle can cause the boat to jump over the front of the trailer, which can result in injury to the boat operator and bystanders.(4) Make sure the boat is centered on the support rails and is headed straight for the bow stop (bumper board). Ease the boat forward until the bow rests against the bow stop. NOTICE: The winch line is not designed to pull the boat onto the trailer.(5) Attach and tighten the winch line.NOTICE: The winch line should not be the only line securing the bow during trailering. Use the chain along with the winch to secure the boat to the trailer.(1) Performthepre-operationchecksshown on page 81 that can be performed on land.(2) Remove all trailering tie-down lines from the boat and attach your docking lines and fenders, if used.(3) Disconnectthetrailerlightsfromthetow- ing vehicle.(4) Back the trailer down the ramp as close to 90° to the shoreline as you can. If pos- sible, have a second person stand aside as an observer. Stop when the wheels are at least halfway submerged. Set the parking brake.(5) Removethebowlinefromtheboweye.(6) Backthetrailerfartherintothewateruntil just the tops of the fenders show, and then reset the parking brake. Board the boat and start it. If possible, remain on the trailer until the engines are warm and areresponding to throttle.(7) Back the boat out into the water, watch-ing carefully for people, other boats, or obstacles.1 Bow eyeTraileringEach launch may have particular differences, Loading1105]]></page><page Index="112" isMAC="true"><![CDATA[Trailering(6)Pull the trailer up the ramp out of the way of other boaters. Attach the bow and stern tie-downs. Reconnect the trailer lights.● Remove all people and all cargo from the boat. Drain any excess water from the bilge using the bilge pump.● Be sure all people are standing clear, and then lift the boat slowly and just far enough to verify that the boat is securely held and properly balanced. If necessary, lower the boat again and adjust the slings.● Whenready,lifttheboatslowlyandcareful- ly.111Stern eye(7) Perform the post-operation checks on page 101.LiftingNOTICEDo not attach lifting cables to the bow eye, cleats, stern eyes, ski tow hook, or hand- grips. Serious damage to the boat can oc- cur. Use only a sling designed specifically for lifting boats.If you need to remove the boat from the water without a trailer, use these guidelines:● Use a sling-type lifting mechanism de-signed for lifting boats. The sling should be covered with a protective material to pre- vent damage to the hull gelcoat.● Use spreader bars to avoid side stress to the hull that may cause cracks in the gel- coat and fiberglass.● Attachguidelinestotheboweyeandstern eyes to control movement of the boat dur- ing lifting.106]]></page><page Index="113" isMAC="true"><![CDATA[Post-operation care Flushing the cooling systemCooling system flushing is essential to pre- vent the cooling system from clogging up with salt, sand, or dirt.(1) Connect the garden hose adapter to agarden hose.Care and storage(4) Makesurethattheareaaroundtheboat is clear, and then start the engine. Imme- diately after the engine starts, fully turn the water supply on so that water flows out continually from the jet thrust nozzle and cooling water pilot outlet. NOTICE: Never turn on the water before starting the engine. The water could flow back through the muffler into the crankcase causing severe engine damage. Be sure to turn on the water immediately after starting the engine to prevent en- gine overheating.(5) Run the engine at a fast idle for 3 to 5 minutes. If the engine stops while flush- ing, turn the water supply off immediately and perform the procedure again from step 4.(6) Turn off the water supply, and then drain residual water from the exhaust system by alternately pushing the remote control lever up to half throttle and back to idle for 10 to 15 seconds.(7) Stop the engine. NOTICE: Never have the water on when the engine is not running. The water could flow back through the muffler into the crankcase causing severe engine damage. Do not run the engine for more than 15 seconds after the water supply has been turned off to avoid engine over- heating.(8) Removethegardenhoseadapter.(9) Installandtightenthecapsecurely.121 Garden hose adapter2 Garden hose(2) Loosentheflushhoseconnectorcapand remove it. Insert the garden hose adapter into the flush hose connector by pushing and twisting it until it is securely connect- ed.1321 Flush hose connector2 Flush hose connector cap3 Garden hose adapter(3) Connectthegardenhosetoawatertap.107]]></page><page Index="114" isMAC="true"><![CDATA[Care and storageCleaning the boatWARNINGGasoline and its vapors are highly flam- mable and explosive. If there is fuel or a fu- el/water mixture in the engine compartment or the fuel tank compart- ment, wipe it up immediately with dry rags. Do not operate the boat until the source of the fuel leak is found and corrected.TIP:Quality Yamaclean®, YamashieldTM, and oth- er Yamalube care products are available from your Yamaha Boat Dealer.(1) Removethefueltankcompartmentdrainplug to drain the water. (See page 77 for fuel tank compartment drain plug removal and installation procedures.) Reinstall the fuel tank compartment drain plug.11 Fuel tank compartment drain plug(2) Removethehulldrainplug.(Seepage78 for hull drain plug removal and installation procedures.)(5) Opentherearplatformhatch.(Seepage 59 for rear platform hatch opening and closing procedures.)(6) Remove the access port cap to let any water drain that has pooled on it. (See page 122 for access port cap removal and installation procedures.) If the boat will be stored on the trailer nearby, leave the cap out until you prepare to launch the boat again. If the boat will be trans- ported on the trailer any distance, tempo-1081 (4)Clean the engine and bilge areas with Yamaclean Bilge CleanerTM or an equiv- alent and rinse with fresh water. Drain all water and wipe up any remaining mois- ture with clean, dry rags. NOTICE: Be careful not to get water on the air filter area or electrical components. Do not use high-pressure water when rinsing the engine or engine compartment as severe engine damage could result.1 Hull drain plug(3) Cleanthehull,boatinterior,anddriveunit with Yamaclean Wash & Wax Concen- trate, or a mild natural soap, and water. Rinse with fresh water. Scum on the hull can be removed with Yamaclean Hull CleanerTM. NOTICE: Incorrect cleaning can damage vinyl. See “Basic stain guide” on page 110.]]></page><page Index="115" isMAC="true"><![CDATA[rarily reinstall the cap and close the hatch until you get home. Open the hatch again when you arrive and remove the cap as before. Leave the cap loose until you plan to transport the boat on the trailer again. NOTICE: Leaving the access port cap out when you are not using or trans- porting the boat helps keep it from be- coming stuck in the access port. (See page 122 for more information.)(7) Securely install the hull drain plug by tightening them until they stop. NOTICE: Before installing the hull drain plug, clean the drain plug thread and O-ring to remove any foreign materials, such as dirt or sand. Otherwise, the hull drain plug could be damaged, allow- ing water to enter the hull. Check the O-ring on the hull drain plug and make sure that the hull drain plug is tight- ened securely before launching the boat. Otherwise, water may flood the boat and cause it to submerge.(8) Spray the exterior of the engine with Yamalube Silicone Protectant and Lubri- cant, or an equivalent. For areas requir- ing heavy protection, use YamashieldTM.(9) Wax the hull with Yamaclean Spray Wax® or other non-abrasive wax de- signed for marine gelcoat. WARNING! Slippery surfaces can cause falls and injury. Be careful not to apply too much wax on deck and gunwale step- ping surfaces. This will make them slippery.(10)Wipe all vinyl and rubber components, such as the seats and engine compart- ment seals, with Yamaclean Vinyl Dress- ingTM or other quality vinyl protectant. NOTICE: Some well-known “protec- tant” products on the market can actu-Care and storageally damage vinyl over time. Consult a Yamaha Boat Dealer if you want to use a product other than Yamaclean Vinyl Protectant.(11) Wash the fabric of the bimini top with a mild natural soap in lukewarm water, then rinse. Do not use detergents. Allow to air dry thoroughly before storage.109]]></page><page Index="116" isMAC="true"><![CDATA[Care and storageBasic stain guideHere are basic steps to remove common stains from boat upholstery. Consult a Yamaha Boat Dealer or upholstery-cleaning professional for difficult stains.TYPE OF STAINSTEPS(rinse with clean, warm water and then dry after application)123General care/DirtAB—Chewing gumEA—Coffee/T ea/ChocolateB——GreaseEB—Ink*CFDKetchupAB—LipstickCBAMustardABCMildew/Wet leaves*CBAMotor oilB——Permanent marker*CFDSuntan lotion*AB—Tar/AsphaltEB—* May cause permanent staining.AMedium-soft brush with warm, soapy waterBYamaclean All Purpose Cleaner or equivalentCIsopropyl alcohol (91% is best)DMixture of 1 tablespoon (15 ml) ammonia, 1/4 cup (60 ml) hydrogen peroxide, and 3/4 cup (177 ml) waterEWipe or scrape off excess (chill gum with ice first)FName brand ink remover110]]></page><page Index="117" isMAC="true"><![CDATA[Battery careIf the boat will not be used for more than a month, remove the battery and store it in a cool, dark place.The battery is located in the battery compart- ment.To remove the battery:(1) Turn the battery switch to the OFF posi-tion. (See page 30.)(2) Disconnect the ground lead (black) andthe negative (–) battery lead (black).(3) Disconnect the positive (+) battery lead(red).(4) Unfasten the battery strap, and then re-move the battery from the boat.Care and storageter) at least once a month and rechargethe battery if it gets too low.T o charge the battery:(1) Remove the caps from the cells. Add dis-tilled water if necessary to top up theelectrolyte to the proper level.(2) Follow the battery manufacturer’s instruc- tions for charging. WARNING! When charging a battery, keep it well away from sparks and open flames, as it gives off explosive gases. When using a battery charger, connect the battery to the charger before you turn on the charger. This will prevent sparking at the terminals that could ignite batterygases.To install the battery:(1) Place the battery in the battery holder,and then fasten the battery using the bat-tery strap.(2) Connectthepositive(+)batterylead(red)to the positive (+) battery terminal.NOTICE: Reversal of the battery leadswill damage the electrical parts.(3) Connect the negative (–) battery lead (black) and the ground lead (black) to the negative (–) battery terminal.(4) Make sure that the battery is securely held in place.231421 Positive (+) battery lead (red)2 Battery strap3 Negative (–) battery lead (black)4 Ground lead (black)To store the battery:(1) Clean the battery casing and terminalsusing a mixture of baking soda and water (one tablespoon of baking soda to one cup of water).(2) Apply dielectric grease or petroleum jelly to the battery terminals and to all ex- posed connectors.(3) If the battery will be stored for a longer period, check its state of charge (use a hydrometer or a voltmeter and load tes-111]]></page><page Index="118" isMAC="true"><![CDATA[Care and storageLong-term storageStoring your boat for prolonged periods of time, such as winter storage, requires preven- tative maintenance to ensure against deterio- ration. It is advisable to have the boat serviced by an authorized Yamaha Boat Dealer before storage. However, the following procedures can be performed by the owner with a mini- mum of tools.Fuel systemFill the fuel tank with fresh fuel, adding one ounce of Fuel Med RX, available from your Yamaha Boat Dealer, to each gallon of fuel or use an equivalent according to the manufac- turer’s instructions. (See page 74 for informa- tion on filling the fuel tank.) Do not “top off” the tank, because fuel could spill. A full fuel tank is less likely to allow condensation to collect in the tank, reducing the chance of contaminat- ed fuel. Running the engine with treated fuel during cooling system flushing will also help protect the fuel system.TIP:Use of Fuel Med RX eliminates the need to drain the fuel system. Consult a Yamaha Boat Dealer or other qualified mechanic if the fuel system is to be drained instead.LubricationIt is advisable to take the boat to a Yamaha Boat Dealer to have the engine fogged for long-term storage.Grease pointsTo keep moving parts sliding or rotating smoothly, coat them with water-resistant grease.Recommended water-resistant grease: YAMALUBE MARINE GREASE or Yamaha Grease A● Throttle cableGrease the throttle-cable inner wires at the pulley wheel of the APS.112● Steeringcableballjointsandinnerwire Grease the steering cable and shift cable ball joints at the jet thrust nozzles. Extend the steering cable and shift cable inner wires and apply a thin coat of grease to them.]]></page><page Index="119" isMAC="true"><![CDATA[● PivotpointsGrease all pivot points of the steering and shift mechanism at the pump end.1● BearinghousingsGrease the bearing housing through the grease nipples. NOTICE: Fill the grease slowly and carefully, because it can dam- age the hoses and the joints.The first service should be done after 10 hours or 1 month by a Yamaha Boat Dealer. Fill the bearing housings with water-resistant grease through the grease nipples.Grease capacity:33.0–35.0 cc (1.11–1.18 oz)After first service: Every 100 hours or 6 months (you may do this yourself).Grease capacity:6.0–8.0 cc (0.20–0.27 oz)1Bearing housing grease nippleCare and storage113]]></page><page Index="120" isMAC="true"><![CDATA[Maintenance MaintenanceBe sure to turn off the engines when you perform maintenance unless otherwise specified. If you are not familiar with ma- chine servicing, this work should be done by a Yamaha Boat Dealer or other qualified mechanic.Maintenance, replacement, or repair of the emission control devices and system may be performed by any marine SI engine repair es- tablishment or individual. Warranty repair, however, must be performed at an authorized Yamaha Boat Dealer. A service manual is available for purchase through a Yamaha Boat Dealer for owners who have the me- chanical skills, tools, and other equipment necessary to perform maintenance not cov- ered by this owner’s/operator’s manual.Owner’s/operator’s manual and tool kitIt is advisable to always carry the owner’s/op- erator’s manual and tool kit with you whenev- er you use the boat.To protect these materials from water dam- age, it would be a good idea to put them in a waterproof bag. If your owner’s/operator’s manual is damaged, order a replacement from a Yamaha Boat Dealer.The service information included in this man- ual is intended to provide you, the owner, with the necessary information for completing your own preventive maintenance and minor re- pairs. The tools provided in the owner’s tool kit are sufficient for this purpose, except that a torque wrench is also necessary for tightening nuts and bolts properly.1 Tool bag2 Screwdriver3 Garden hose adapter4 10/12 mm box wrench5 Pliers6 10/12 mm open-end wrench7 Hexagon wrench1234567WARNING114]]></page><page Index="121" isMAC="true"><![CDATA[Periodic maintenance chartThe periodic maintenance chart gives general guidelines for periodic maintenance. Have a Yamaha dealer perform the checks in the following chart. However, maintenance may need to be performed more frequently depending on your operating conditions. If you have any ques- tions, consult a Yamaha dealer.This “ √ ” mark indicates items to be checked and serviced by a Yamaha dealer.MaintenanceItemOperationInitialThereafter every10 hours50 hours or 12 months *1100 hours or 12 months *1200 hours or 24 months *1Fuel hoses, clamps, canister, and check valveCheck for damage, and check con- nections and tightening of clamps√Fuel filler capCheck cap for damage, and check seal for cracks and deformation√Fuel tankCheck installation√√Main switch and en- gine shut-off switchCheck operation√√BatteriesCheck state of charge and termi- nals, and check for broken battery straps√Battery leadsCheck terminals√Battery switchesCheck operation√√Meters (after com- pleting the pre-opera- tion checks)Check lighting√√Neutral switchesCheck operation√√Hatch interlock switches (wet storage compartment)Check operation√√BlowerCheck operation√√HornCheck operation√√Navigation lightsCheck lighting√√Electric bilge pumpCheck for water discharge by auto- matic operation, clean filter, check hoses for damage, and check tight- ening of clamps√Other electrical com- ponentsCheck operation of livewell, jet wash, stereo, and other components√√Steering master ASSYCheck operation and tilting mecha- nism, and check for looseness√√Steering cablesCheck connections and exterior, and lubricate√Articulating keelCheck operation, and check link rod for bends and damage√115]]></page><page Index="122" isMAC="true"><![CDATA[MaintenanceItemOperationInitialThereafter every10 hours50 hours or 12 months *1100 hours or 12 months *1200 hours or 24 months *1Remote control le- versCheck exterior and operation, check shift operation, and check for loose- ness√√Throttle cablesCheck connections and exterior, and lubricate√Shift cablesCheck connections and exterior, and lubricate (shift gate end)√Exhaust hoses, wa- ter locks, and resona- torsCheck for exhaust leakage, and check clamps at connections√Drain passagesRemove clogs√Drain plugsCheck O-rings√√Hull and deckCheck for damage√√Windshield and seatsCheck installation and operation, and check for damage√√T-top (210 FSH Sport) and bimini top(210 FSH Sport/210 FSH Deluxe)Check installation, and check for damage√√Hatches, hinges, and packing sealsCheck installation√√LadderCheck installation√√Access port capsCheck exterior and installation√Spark plugsCheck√√High-pressure fuel hosesCheck connections and exterior, and check for leakage√Engine oilReplace√√√Engine oil filtersReplace√Air filter elementsCheck for damage and dirt√Intake hoses and breather hosesCheck for damage, and check con- nections√Throttle bodiesLubricate throttle valves√Anodes (engines)Check for corrosion√ *2Valve clearanceCheck and adjust√ *2Rubber couplingsCheck for looseness and noise√Engine mountsCheck for damage and peeling√Cooling water hoses and cooling water pi- lot outlet hosesCheck for damage, and check con- nections√Water inlet strainersCheck for damage√√Intake gratesCheck for damage√√ImpellersCheck for bends, damage, and for- eign material√√Impeller ductsCheck and lubricate√116]]></page><page Index="123" isMAC="true"><![CDATA[MaintenanceItemOperationInitialThereafter every10 hours50 hours or 12 months *1100 hours or 12 months *1200 hours or 24 months *1Jet thrust nozzlesCheck movement, and lubricate√Intermediate hous- ingsLubricate√Anodes (jet pump units)Check for corrosion√*1: Whichever comes first.*2: Check every 200 hours.Perform the pre-operation checks and post-operation checks before performing periodic main- tenance.117]]></page><page Index="124" isMAC="true"><![CDATA[SpecificationsSpecificationsITEMSpecificationBoat capacityMaximum people on board10 personMaximum load capacity1021 kg (2250 lb)Dimensions and weightLength6480 mm (255.1 in)Beam2600 mm (102.4 in)Height210 FSH Sport 2860 mm (112.6 in)210 FSH Deluxe/210 FSH 2160 mm (85.0 in)Draft210 FSH Sport 240 mm (9.4 in)210 FSH Deluxe/210 FSH 173 mm (6.8 in)Dry weight210 FSH Sport 1362 kg (3003 lb)210 FSH Deluxe 1323 kg (2917 lb)210 FSH 1285 kg (2833 lb)PerformanceMaximum fuel consumption67.0 L/h (17.7 US gal/h, 14.7 Imp.gal/h)Cruising range at full throttle2.94 hourTrolling speed1500 ±100 r/minEngineNumber of engines2Engine typeLiquid cooled 4-stroke, DOHCNumber of cylinders3Engine displacement1049 cm3Bore × stroke82.0 × 66.2 mm (3.23 × 2.61 in)Compression ratio11.0 : 1Valve clearance-intake (cold)0.15–0.22 mm (0.0059–0.0087 in)Valve clearance-exhaust (cold)0.26–0.32 mm (0.0102–0.0126 in)Lubrication systemDry sumpCooling systemWaterStarting systemElectricIgnition systemT.C.I.Spark plug (NGK)CR9EBSpark plug gap0.7–0.8 mm (0.028–0.031 in)Battery capacity12 V, 85 AhCharging systemFlywheel magneto118]]></page><page Index="125" isMAC="true"><![CDATA[SpecificationsITEMSpecificationDrive unitPropulsion systemJet pumpJet pump typeAxial flow, single stageImpeller rotationCounterclockwisePitch angle11.2°TransmissionDirect drive from engineJet thrust nozzle angle23.0+23.0°Fuel and oilRecommended fuelRegular unleaded gasolineMinimum octane rating (PON)86Minimum octane rating (RON)90Fuel tank total capacity197 L (52.0 US gal, 43.3 Imp.gal)Recommended engine oilYAMALUBE 4W or 4-stroke motor oilRecommended engine oil type SAESAE 10W-30, 10W-40, 20W-40, 20W-50Recommended engine oil grade APIAPI SG, SH, SJ, SLEngine oil total quantity3.7 L (3.91 US qt, 3.26 Imp.qt)Engine oil quantity without oil filter replacement3.4 L (3.59 US qt, 2.99 Imp.qt)Engine oil quantity with oil filter replacement3.2 L (3.38 US qt, 2.82 Imp.qt)Fuse amperageElectronic throttle valve fuse10 AFuel pump fuse10 AMain relay drive fuse10 AMain fuse20 ABattery fuse30 AAccessory fuse20 ABilge pump fuse3A119]]></page><page Index="126" isMAC="true"><![CDATA[Trouble recoveryTroubleshootingIf you have any trouble with your boat, use this section to check for the possible cause. If you cannot find the cause or if the procedure for replacement or repair is not described in this own- er’s/operator’s manual, ask your Yamaha Boat Dealer or a qualified mechanic for the proper service.Troubleshooting chartThe Troubleshooting chart contains: “TROUBLE,” “POSSIBLE CAUSE,” “REMEDY,” and “PAGE.”Check the possible cause and remedy, and also the referred page for the maintenance steps to solve the trouble.TROUBLEPOSSIBLE CAUSEREMEDYPAGEStarter mo- tor does not turn overFuseBurned outReplace fuse and check wiring124BatteryRun downRecharge111Poor terminal con- nectionsTighten as required111Battery switch offTurn on switch30Rear platform hatchNot latchedLatch securely59Starter compo- nentFaultyHave serviced by Yamaha Boat Dealer—Remote control leverNot in neutral posi- tionMove remote control lever to neutral position32Starter mo- tor turns over/engine does not startEngine shut-off switchClip on cord is not in placeInstall clip in engine shut-off switch30FuelEmptyRefill as soon as possible74Stale or contaminat- edHave serviced by Yamaha Boat Dealer—Fuel tankWater or dust collect- edHave serviced by Yamaha Boat Dealer—Spark plugFouled or defectiveHave serviced by Yamaha Boat Dealer—CrankcaseFilled with fuelHave serviced by Yamaha Boat Dealer—Filled with waterHave serviced by Yamaha Boat Dealer—Fuel filterClogged or water col- lectedHave serviced by Yamaha Boat Dealer—120]]></page><page Index="127" isMAC="true"><![CDATA[Trouble recoveryTROUBLEPOSSIBLE CAUSEREMEDYPAGEWarning is displayedOver temperature warning*Jet intake cloggedClean122Cooling system cloggedClean90Low oil pressure warning*Oil pressure droppedHave serviced by Yamaha Boat Dealer—FuelEmptyRefill as soon as possible74Check engine warningFaulty sensorsHave serviced by Yamaha Boat Dealer—Engine runs irregularly or stallsFuelEmptyRefill as soon as possible74Stale or contaminat- edHave serviced by Yamaha Boat Dealer—Fuel filterWater or dust collect- edHave serviced by Yamaha Boat Dealer—Fuel tankWater or dirt presentHave serviced by Yamaha Boat Dealer—Spark plugFouled or defectiveHave serviced by Yamaha Boat Dealer—Incorrect heat rangeHave serviced by Yamaha Boat Dealer—Gap incorrectHave serviced by Yamaha Boat Dealer—Boat speed too slow or loses powerCavitationJet intake cloggedClean122Engine overheat*Jet intake cloggedClean122Cooling system cloggedClean90Fuel filterCloggedHave serviced by Yamaha Boat Dealer—Spark plugFouled or defectiveHave serviced by Yamaha Boat Dealer—Incorrect heat rangeHave serviced by Yamaha Boat Dealer—Gap incorrectHave serviced by Yamaha Boat Dealer—FuelStale or contaminat- edHave serviced by Yamaha Boat Dealer—*Engine speed will be limited to 3500 rpm.121]]></page><page Index="128" isMAC="true"><![CDATA[Trouble recoveryEmergency procedures Jet pump clean-out procedureSevere injury or death may result if you ig- nore any of the following:● Turn off and remove both main switchkeys, remove the clip from the engine shut-off switch, and wait for all move- ment to stop before removing the ac- cess port caps.● Never override the interlocks to run the engines with the rear platform hatch open.● The impellers have sharp edges. Be careful when reaching into jet pump ar- eas.If weeds or debris get caught in the intakes or impellers, cavitation can occur, and though the engine speed rises, forward thrust will de- crease. If this condition is allowed to continue, jet pump damage can occur and the engines may overheat and seize. If there is any sign that a jet intake or impeller is clogged with weeds or debris, follow this clean-out proce- dure.(1) Turn off and remove the main switch key, remove the clip from the engine shut-off switch, and wait for all movement to stop.(2) Opentherearplatformhatch.(Seepage 59.)(3) Checkthattheretainingcordissecurely attached to the access port cap and strap eye.1 2(4)Retaining cord Strap eyeWhile holding the handle and pushing down, turn the access port cap counter- clockwise until the “SET” mark is aligned with the slot, and then lift the cap by the handle.2112WARNINGNOTICE● Donotliftorpullthecapwiththeretain- ing cord.● Set the cap where it cannot be acciden- tally knocked overboard.1212212 Slot“SET” mark]]></page><page Index="129" isMAC="true"><![CDATA[Trouble recovery13121 Access port cap(5) Remove any weeds or debris from the drive shaft, impeller, pump housing, and jet thrust nozzle. If you cannot remove the debris, consult a Yamaha Boat Deal- er.(6) To reinstall the access port cap, first clean off any sand or other foreign matter from the cap or port surfaces. Apply a light coat of Yamalube Waterproof Ma- rine Grease (P/N: ACC-GREAS-10-CT), if available, to the seal of the access port cap. If grease is not available, apply the grease during the post-operation checks.(7) Insert the cap so that the “SET” mark is aligned with the slot, and then while pushing the handle turn the cap clock- wise until the “SET” mark is aligned with the edge of the access port.1 “SET” mark2 Slot3 Edge of the access port(8) Checkthatthecapisperpendiculartothe centerline of the boat. Pull the handle forcefully to make sure that the cap is locked securely. If a strong pull will move the access port cap, it is not locked se- curely—the cap could be forced out by water pressure during operation.11 Perpendicular to the centerline of the boat(9) Closetherearplatformhatch.NOTICE● Besuretheaccessportcapsarelocked securely in place. Otherwise, the caps could be forced out of the access ports by water pressure, causing loss of per- formance and possible damage.123]]></page><page Index="130" isMAC="true"><![CDATA[Trouble recovery● Therearplatformhatchhasinterlocksto shut off the engines should the hatch be accidentally opened during operation. The engines will not restart unless the hatch is closed and latched.Jump-startingSevere injury or death may result if you ig- nore any of the following:● If the blower will not operate, ventilatethe engine compartment by opening the engine hood for several minutes before attempting a jump-start.● Do not connect the negative (–) jumper cable to the negative (–) terminal of the dead battery. Sparks could ignite battery or fuel vapors, which could cause an ex- plosion.If the boat battery runs down, the engine can be started in an emergency using a 12-volt booster battery and jumper cables.To connect the jumper cables:(1) Connect the positive (+) terminal of the dead battery to the positive (+) terminal of the booster battery with the positive (+) jumper cable.(2) Connect one end of the negative (–) jumper cable to the negative (–) terminal of the booster battery.(3) Connecttheotherendofthenegative(–) jumper cable to an engine hanger. NOTICE: Be sure all connections are secure and correct before attempting to start the engine. Any wrong con- nection may damage the electrical system.1 Negative (–) jumper cable 2 Positive (+) jumper cable 3 Engine hanger4 Booster battery(4) Starttheengine,andthendisconnectthe jumper cables by reversing the above steps. NOTICE: Do not turn the main switch key for more than 5 seconds. If the engine does not start in 5 seconds, release the main switch key and try again after 15 seconds. Continuous cranking for more than 5 seconds will discharge the battery and the engine will not start. The starter motor may also be damaged if it is engaged con- tinuously for more than 5 seconds.Fuse replacementDo not use fuses of a higher amperage than recommended. Substitution with a fuse that has an improper rating can cause extensive electrical system damage and possible fire.If a fuse is blown, replace it with the proper fuse.To replace a fuse:(1) Opentheenginehood.(Seepage53.) (2) Unfastentheband.1243WARNINGWARNING124]]></page><page Index="131" isMAC="true"><![CDATA[1 Band871 Electronic throttle valve fuse 2 Fuel pump fuse3 Main relay drive fuse4 Main fuse5 Fuse puller 6 Battery fuse 7 Spare fuse 8 Unused fuse(5) When replacing the accessory fuse and bilge fuse, remove the fuse holder. (Open the battery compartment to access the accessory fuse and bilge fuse. [See page 62.])2311 Fuse holder2 Accessary fuse 3 Bilge fuse(6) Replace the blown fuse with the spare fuse of the correct amperage by using the fuse puller.1(3) Remove the fuse box from the air filter case by pulling the fuse box toward the bow.(4) Whilepushingbothsidesofthefusebox cover inward, pull the cover toward the bow and remove it.11 Fuse box coverTrouble recovery123456125]]></page><page Index="132" isMAC="true"><![CDATA[Trouble recoveryTowing the boatFuse amperage:Electronic throttle valve fuse:10 AFuel pump fuse:10 AMain relay drive fuse:10 A Main fuse: 20 ABattery fuse: 30 AAccessory fuse: 20 ABilge fuse: 3AWARNING(7) Installthefuseboxcover.(8) Iftheaccessoryfuseorbilgefusewasre-placed, install the fuse holder.(9) Installthefuseboxtotheairfiltercase.(10) Fasten the band.(11) Close the engine hood.● The operator of the towing boat must keep speed to a minimum and avoid traf- fic or obstacles which could be a hazard to either boat.● The towing line should be long enough so the towed boat will not collide with the towing boat when slowing down.The boat should be towed only if it becomes inoperative.The towing rope should be long enough so that the boat will not collide with the towing boat when slowing down. A good rule of thumb is a tow rope which is three times the combined length of the towing boat and the boat.Tow the boat using the bow eye only. Tow the boat at a no-wake speed. NOTICE: Do not tow the boat at speed fast enough to leave a wake (8 km/h, 5 mph). Severe engine damage could result because water can flood the non-operating engine through the water intake.11261 Bow eye]]></page><page Index="133" isMAC="true"><![CDATA[Consumer information Limited warrantyYAMAHA MOTOR CORPORATION, U.S.A. YAMAHA BOAT LIMITED WARRANTYYamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha Boats will be free from defects in materials or workmanship for the period of time stated herein, subject to certain stated limitations.PERIOD OF WARRANTY: The hull and deck on any new Yamaha Boat purchased for pleasure use from an authorized Yamaha Boat dealer in the United States will be warranted against major structural defects for a period of five (5) years in pleasure use, or for one (1) year in commercial applications. All other Yamaha Boat components will be warranted against defects in material or workmanship, subject to exclusions noted herein, for a period of one (1) year from date of purchase in pleasure use, or ninety (90) days from the date of purchase in commercial applications.Replacement parts used in warranty repairs will be warranted for the balance of the applicable warranty period.The warranty described here applies to boats purchased and registered for use in the United States only. For warranty provisions outside the United States, contact that particular country’s local Yamaha distributor.OBTAINING REPAIRS UNDER WARRANTY: During the period of warranty, any authorized Yamaha Boat dealer will, free of charge, repair or replace, at Yamaha’s option, any parts adjudged defective by Yamaha due to faulty workmanship or material from the factory. All parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A.CUSTOMER’S RESPONSIBILITY: Under the terms of this warranty, the customer will be respon- sible for ensuring that the boat is properly operated, maintained, and stored as specified in the applicable Owner’s Manual.The owner of the boat shall give notice to an authorized Yamaha Boat dealer of any and all appar- ent defects within ten (10) days of discovery and make the boat available at that time for inspection and repairs at the dealer’s place of business.GENERAL EXCLUSIONS FROM WARRANTY: This warranty will not cover the repair of damage if the damage is a result of abuse or neglect of the product. Examples of abuse and neglect include, but are not limited to:1. Racing or competition use, modification of original parts, abnormal strain.2. Lack of proper maintenance and off season storage as described in the Owner’s Manual, installation of parts or accessories that are not equivalent in design and quality to genuine Yamaha parts.3. Use of lubricants, oils, and fuel/oil mixtures that are not suitable for boat motor use.4. Damage as a result of accidents, collisions, contact with foreign materials, or submersion.5. Growth of marine organisms on motor or hull surfaces.6. Normal deterioration.7. Gel coat stress cracks.127]]></page><page Index="134" isMAC="true"><![CDATA[Consumer informationSPECIFIC PARTS EXCLUDED FROM WARRANTY; Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not covered by warranty. Charges for transporting the boat to and from an authorized Yamaha Boat dealer are excluded from warranty coverage.EMISSION CONTROL WARRANTY: Yamaha warrants to the ultimate purchaser and any subsequent owner, that the exhaust emission control components on this engine are designed, built and equipped so as to conform at the time of sale with applicable regulations under section 213 of the Clean Air Act and that this engine is free from defects in materials and workmanship which cause said engine to fail to conform with applicable regulations for thirty (30) months from the date of purchase or 175 hours of operation, whichever comes first. For evaporative emission components, for a failure that will increase evaporative emissions, the warranty coverage is two (2) years from the date of purchase. Some states may have different emission control warranty provisions. As these vary from state to state, consult your Yamaha dealer or contact Yamaha Customer Relations at 1-800-962-7926 for more information.TRANSFER OF WARRANTY: Transfer of the warranty from the original purchaser to any subse- quent purchaser is possible by having the boat inspected by an authorized Yamaha Boat dealer and requesting the dealer to submit a change of registration to Yamaha Motor Corporation, USA within ten (10) days of the transfer.YAMAHA MOTOR CORPORATION, USA MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, USA AND EXCLUDED FROM THIS WARRANTY.SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.YAMAHA MOTOR CORPORATION, U.S.A. Post Office Box 6555 Cypress, California 90630WARRANTY QUESTIONS AND ANSWERSQ. What costs are my responsibility during the warranty period?A. The customer’s responsibility includes all costs of normal maintenance services, non-warrantyrepairs, accident, and collision damages.Q. What are some examples of “abnormal” strain, neglect, or abuse?A. These terms are general and overlap each other in areas. Specific examples include:Running the boat out of oil, operating the boat with a broken or damaged part which causes another part to fail, and so on. If you have any specific questions on operation or maintenance, please contact your Yamaha Boat dealer for advice.Q. Does the warranty cover incidental costs such as transportation due to a failure? A. No. The warranty is limited to repair of the boat itself.128]]></page><page Index="135" isMAC="true"><![CDATA[Consumer informationQ. May I perform any or all of the recommended maintenance shown in the Owner’s Manual instead of having the dealer do them?A. Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s and Service Manual. We do recommend, however, that items requiring special tools or equipment be done by a Yamaha Boat dealer.Q. Will the warranty be void or cancelled if I do not operate or maintain my new boat exactly as specified in the Owner’s Manual?A. No. The warranty on a new boat cannot be “voided” or “cancelled.” However, if a particular failure is caused by operation or maintenance other than as shown in the Owner’s Manual, that failure may not be covered under warranty.Q. What responsibility does my dealer have under this warranty? A. Each Yamaha Boat dealer is expected to:1. Completely set up each new boat before sale.2. Explain the operation, maintenance, and warranty requirements to your satisfaction at thetime of sale, and upon your request at any later date. In addition, each Yamaha Boat dealer is held responsible for his setup, service and warranty repair work.Q. Is the warranty transferable to second owners?A. Yes. The remainder of the existing warranty can be transferred upon request. The unit hasto be inspected and re-registered by an authorized Yamaha Boat dealer for the policy to remain effective.CUSTOMER SERVICEIf your boat requires warranty service, you must take it to any authorized Yamaha Boat dealer within the United States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regarding warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. If you are still not satisfied and require additional assistance, please write:YAMAHA MOTOR CORPORATION, U.S.A. CUSTOMER RELATIONS DEPARTMENT P.O. Box 6555Cypress, California 90630CHANGE OF ADDRESSThe federal government requires each manufacturer to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is compiled from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.If you should move after you have purchased your new boat, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number [or deal- er’s name] as it is shown on your warranty card, your name and new mailing address.Mail to:YAMAHA MOTOR CORPORATION, U.S.A. WARRANTY DEPARTMENT1270 Chastain RoadKennesaw, Georgia 30144This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.129]]></page><page Index="136" isMAC="true"><![CDATA[Consumer informationYAMAHA EXTENDED SERVICE (Y.E.S.)Keep your Yamaha Boat protected even after the 1-year warranty coverage provisions expire with genuine Yamaha Extended Service (Y.E.S.).Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maxi- mum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.• Y.E.S. is flexible. You choose the plan that’s right for you: 12 months, 24 months, or 36 months beyond the 1-year warranty cover- age period. That means you can get up to 5 years of coverage on the power train, controls, and other components to match the comforting 5-year standard protection on the hull.• Y.E.S. is designed and administered by the same Yamaha people who handle your war- ranty–and it shows in the comprehensive coverage benefits. There are no limitations on hours of use. Coverage isn’t limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufactur- ing defects just like the warranty. See the sample contract at your Yamaha dealer to see how comforting uninterrupted factory- backed protection can be.• You don’t have to pay anything for cov- ered repairs. There’s no deductible to pay, and repairs aren’t “prorated.” You don’t have any “out-of-pocket” expenses for covered repairs.• In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $250 reimbursement per occurrence for any rea-sonable expenses you incur because your Yamaha needs covered service: replace- ment vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb cov- erage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.• Y.E.S. coverage is honored at any autho- rized Yamaha dealer nationwide.• Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make your Yamaha Boat much more valuable!This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the first year of the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service. We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires. See your dealer today!A special note:If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number or Hull Identification Number. We’ll be happy to help you get the Y.E.S. coverage you need.Yamaha Service Marketing P.O. Box 6555Cypress, CA 90630 1-(866)-YES-EXTD (1-866-937-3983)130]]></page><page Index="137" isMAC="true"><![CDATA[Consumer informationSample float planLeave a float plan with a responsible person on shore before boating. The example below can be copied and used.FLOAT PLANVESSEL INFORMATIONBOAT MAKE: Yamaha MOTOR TYPE: JetMODEL:LENGTH: REGISTRATION NO:DECK COLOR: HULL COLOR:PASSENGEROPERATOR EMERGENCY PHONE: ADDRESS:PASSENGER #1: EMERGENCY PHONE: ADDRESS:PASSENGER #2: EMERGENCY PHONE: ADDRESS:PASSENGER #3: EMERGENCY PHONE: ADDRESS:PASSENGER #4: EMERGENCY PHONE: ADDRESS:DEPARTURE INFORMATIONPOINT OF DEPARTURE: DATE/TIME:TOW VEHICLE LICENSE: TRAILER LICENSE: MAKE / MODELDESTINATION INFORMATIONDESTINATION:LORAN OR GPS COORDINATES:INTENDED ACTIVITY:EXPECTED RETURNDATE:TIME:LOCAL U.S. COAST GUARD PHONE #:NOTES: HULL COLOR:OPERATOR EMERGENCY PHONE: ADDRESS:PASSENGER #1: EMERGENCY PHONE: ADDRESS:131]]></page><page Index="138" isMAC="true"><![CDATA[IndexAAccess port cap check ............................. 85 Accessory outlet....................................... 51 Additional equipmentrecommendations ................................. 13 Anchor lightDData bar ................................................... 36 Docking .................................................... 98 Drain plug check ...................................... 87 Driving your boat ...................................... 92EEmergency procedures .......................... 122 Emission control information ...................... 2 Engine break-in ........................................ 80 Engine hood ............................................. 53 Engine oil ................................................. 75 Engine oil level check............................... 86 Engine oil requirement ............................. 75 Engine serial number ................................. 1 Engine shut-off cord (lanyard) check ....... 89 Engine shut-off switch .............................. 30 Engine shut-off switch check.................... 90 Enjoy your boat responsibly ..................... 21FFire extinguisher check ............................ 84 Flushing the cooling system ................... 107 Fuel .......................................................... 74 Fuel level check ....................................... 90 Fuel requirement ...................................... 74 Fuel system ............................................ 112 Fuel system checks.................................. 86 Fuse replacement .................................. 124GGeneric warning ....................................... 46 Getting to know your boat ........................ 92 Glossary, boat .......................................... 22 Glove compartment .................................. 58 Grease points ......................................... 112HHazard information ................................... 14 Hitch ....................................................... 103(210 FSH Deluxe/210 FSH).................. 64 Anchor light (210 FSH Sport) ................... 64 Anchor storage compartment ................... 53 Anchoring ................................................. 99 Approval label of emission controlcertificate ................................................ 2BBacking your trailer ................................ 104 Basic stain guide .................................... 110 Battery care............................................ 111 Battery check ........................................... 87 Beaching .................................................. 99 Bilge water check ..................................... 87 Bilge water, draining................................. 77 Bilge water, draining on land.................... 77 Bilge water, draining on water .................. 78 Bimini top (210 FSH Deluxe).................... 71 Bimini top (210 FSH Sport) ...................... 70 Bimini top, installing (210 FSH Deluxe).... 73 Bimini top, removing (210 FSH Deluxe) ... 73 Bimini top, setting up(210 FSH Deluxe) ................................. 71 Bimini top, storing in the fully collapsedposition (210 FSH Deluxe).................... 73 Bimini top, storing in the upright position(210 FSH Deluxe) ................................. 72 Bimini top, trailering (210 FSH Deluxe) .... 73 Blower switch check................................. 88 Boarding from a dock or landing jetty....... 98 Boarding from the water ........................... 98 Boat characteristics.................................. 14 Boat control functions............................... 30 Boating with passengers .......................... 97CCheck engine warning.............................. 44 Cleaning the boat ................................... 108 Cooling water pilot outlet check ............... 90 Courtesy light switch ................................ 48132Crossing wakes and swells .................... 100 Cruise assist............................................. 42 Cruising information display(trip screen tab)..................................... 37 Cruising limitations ................................... 11]]></page><page Index="139" isMAC="true"><![CDATA[Horn switch check .................................... 89 Hull Identification Number (HIN) ................ 1IIdentification number records ..................... 1 Information display (home screen tab) ..... 36JJet intake checks...................................... 86 Jet pump clean-out procedure ............... 122 Jump-starting ......................................... 124LIndexOver temperature warning ....................... 44 Owner’s/operator’s manual and toolkit ........................................................ 114Periodic maintenance chart.................... 115 Post-launch checks .................................. 90 Post-operation care ................................ 107 Post-operation checks............................ 101 Pre-launch checks.................................... 83 Pre-operation check points ...................... 83 Pre-operation checklist............................. 81 Primary Identification (PRI-ID) number ...... 1RRemote control lever checks .................... 83 Remote control levers .............................. 32 Required equipment ................................. 13 Resetting the settings to the defaultsettings ................................................. 41 Reverse RPM control ............................... 43 Rules of the road ...................................... 17SSample float plan ................................... 131 Screen tabs (screen tab bar).................... 36 Seats ........................................................ 52 Selecting the display units........................ 39 Setting the aeration time(aerator button) ..................................... 40 Setting the day mode and night mode ..... 39 Setting the display language .................... 40 Setting the time ........................................ 38 Specifications ......................................... 118 Starboard/port engine wellness alarmdisplay ................................................... 39 Starting the engine ................................... 92 Steering .................................................... 33 Steering system checks ........................... 83 Stereo system .......................................... 51 Stopping the boat ..................................... 97 Stopping the engines ............................... 94 Storage compartments ............................. 53 Swim platform and ladder ........................ 66 Switch circuit breakers ............................. 50 Switches ................................................... 47Labels, important........................................ 4 Labels, other .............................................. 9 Labels, warning .......................................... 6 Launching............................................... 104 Learning to operate your boat .................. 92 Leaving a dock ......................................... 95 Lifting...................................................... 106 Limitations on who may operate theboat....................................................... 10 Limited warranty ..................................... 127 Loading .................................................. 105 Long-term storage .................................. 112 Low oil pressure warning ......................... 44 Lubrication.............................................. 112MMain components, location ...................... 23 Main switches........................................... 31 Maintenance........................................... 114 Manufactured date label............................. 3 Multi-function display elements ................ 35 Multi-function display unit operation......... 35 Multi-function display unit settings(setting screen tab) ............................... 38NNavigation and anchor lights switch......... 48 Navigation and anchor lights switchcheck .................................................... 88 Night operation......................................... 15 No-wake mode ......................................... 41 No-wake mode/cruise assist switch ......... 41OOperational requirements......................... 12P133]]></page><page Index="140" isMAC="true"><![CDATA[IndexTTachometers ............................................ 35 Tilt lever.................................................... 34 To get more boating safety information.... 21 Towing the boat...................................... 126 Trailering checklist ................................. 103 Trailering the boat .................................. 103 Troubleshooting ..................................... 120 Troubleshooting chart ............................ 120 T-top (210 FSH Sport).............................. 70 Turning the boat ....................................... 95WWakeboarding and water-skiing............... 16 Warning definition table............................ 43 Warnings .................................................. 43 Wet storage compartment........................ 59 Windshield................................................ 63YYAMAHA EXTENDED SERVICE(Y.E.S.) ............................................... 130134]]></page><page Index="141" isMAC="true"><![CDATA[For your best ownership experience, think Genuine Yamaha!Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for aftermarket parts that may not provide full confidence and satisfaction?Genuine Yamaha Accessories – Yamaha only offers accessories that meet our high standards for quality and performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and perform right – right out of the box.Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products. They’re formulated and approved by the toughest judges we know: the Yamaha engineering teams that know your Yamaha from the inside out.Genuine Yamaha Service Manuals – Get the same factory manual for your vehicle that the technicians at your authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you can order them directly through yamahapubs.com.Genuine Yamaha products are available only from your Yamaha dealer. Find out more at yamaha-motor.com]]></page><page Index="142" isMAC="true"><![CDATA[Printed in USAJuly 2017–0.3 × 1 CR]]></page></pages></Search>